Learn with Anil · JKSSB JE Civil PYQsPractise online →Subscribe ₹149

JKSSB JE Civil 2025 question paper with answers

JKSSB Junior Engineer (Civil) OMR Exam 2025 (2 November) Question Paper. JKSSB JE (Civil) OMR test: 120 Civil Engineering questions in 120 minutes, 1 mark each, ¼ mark cut for each wrong answer, in English. Held on 2 November 2025 (JKSSB Advt. No. 03 of 2025, Series A). All four options with the answer from JKSSB's final answer key (24 November 2025), plus a short explanation for every question (the first 10 here, all of them in the app). Each question is shown in English and Hindi, as printed in the booklet.

यूपीएससी सीएपीएफ (असिस्टेंट कमांडेंट) 2025 प्रश्न पत्र, उत्तर कुंजी सहित

Attempt this paper · 120 min timerMake a topic-wise quiz

The correct answer to every question is free on this page, and so are the explanations of the first 10. For all 120 explanations, practise the paper in the app with the ₹149 All-in-One Pass, one payment for every exam on the site.

Subjects in this paper

All 120 questions

  1. Q1 · Surveying · Surveying

    Which of the following set of terms does not relate to operation of a theodolite?

    1. Transiting and inverting
    2. Face left and face right
    3. Right swing and left swing
    4. Gauging and sounding
    Show answer

    Answer: (4) Gauging and sounding

    Transiting (plunging) the telescope, face left/face right observations and swinging the telescope right or left are all theodolite operations. Gauging (measuring stream discharge) and sounding (measuring water depth) belong to hydrographic surveying, not to theodolite work.

  2. Q2 · Surveying · Surveying

    If the whole circle bearing is 315°20′, its quadrantal bearing would be

    1. S 36°30′ W
    2. N 44°40′ W
    3. N 57°24′ W
    4. S 60°40′ W
    Show answer

    Answer: (2) N 44°40′ W

    A WCB between 270° and 360° lies in the NW quadrant, so QB = N (360° − WCB) W = N (360° − 315°20′) W = N 44°40′ W.

  3. Q3 · Surveying · Surveying

    Error due to inclination of line of collimation in levelling across a river can be eliminated by

    1. Reversion
    2. Reciprocal ranging
    3. Reciprocal levelling
    4. Keeping level in middle
    Show answer

    Answer: (3) Reciprocal levelling

    Across a river the level cannot be set up midway between the two points, so reciprocal levelling is used: readings are taken with the level near each bank in turn and the mean of the two apparent differences of level cancels the collimation error (and curvature and refraction).

  4. Q4 · Surveying · Surveying

    The length of a survey line when measured with a chain of 20 m nominal length was found to be 841.5m. If the chain used is 0.1 m too long, the correct length of the measured line is

    1. 845.7 m
    2. 837.3 m
    3. 841.6 m
    4. 839.4 m
    Show answer

    Answer: (1) 845.7 m

    True length = (L′/L) × measured length = (20.1/20) × 841.5 = 845.7 m. A chain that is too long gives a measured length that is too short, so the correction is positive.

  5. Q5 · Surveying · Surveying

    In any closed traverse, if the survey work is error free, then I. The algebraic sum of all the latitudes should be equal to zero II. The algebraic sum of all the departures should be equal to zero III. The sum of the northings should be equal to the sum of the southings Which of the above statements are correct?

    1. I and II
    2. I and III
    3. II and III
    4. I, II and III
    Show answer

    Answer: (4) I, II and III

    For an error-free closed traverse the closing error is zero, so ΣL = 0 and ΣD = 0. ΣL = 0 simply means the sum of northings (+ latitudes) equals the sum of southings (− latitudes), so all three statements hold.

  6. Q6 · Surveying · Surveying

    Consider the following statements: Reciprocal leveling eliminates the effect of I. Errors due to earth's curvature II. Errors due to atmospheric refraction III. Mistakes in taking levelling staff readings IV. Error due to line of collimation Which of these statements are correct?

    1. I, II and III
    2. I, III and IV
    3. II, III and IV
    4. I, II and IV
    Show answer

    Answer: (4) I, II and IV

    In reciprocal levelling the true difference of level is the mean of the two apparent differences, so the errors of curvature, refraction (assumed equal in both observations) and collimation cancel out. Mistakes in reading the staff are blunders and are not eliminated by any method.

  7. Q7 · Surveying · Surveying

    Consider the following statements about the characteristics of contours: I. Closed contour lines with higher values inside show a lake II. Contour is an imaginary line joining points of equal elevations III. Closely spaced contours indicate steep slope IV. Contour lines can cross each other in case an overhanging cliff Which of these statements are correct?

    1. II, III and IV
    2. I and II
    3. I and IV
    4. I, II and III
    Show answer

    Answer: (1) II, III and IV

    Closed contours with higher values inside indicate a hill; a lake or depression has lower values inside, so I is wrong. A contour joins points of equal elevation, close spacing means a steep slope, and contours cross only at an overhanging cliff (or cave), so II, III and IV are correct.

  8. Q8 · Surveying · Surveying

    Match List - I with List-II and select the correct answer using the codes given below the lists: List - I (Type of survey) — List - II (Purpose) i. Topographical survey — 1. To determine boundaries of fields, houses, etc. ii. Reconnaissance survey — 2. To find relics of antiquity iii. Cadastral survey — 3. To determine natural features of a country iv. Archaeological survey — 4. To determine possibility and rough cost of the surveying system to be adopted Choose the correct option:

    1. (i) - 3, (ii) - 4, (iii) - 1, (iv) - 2
    2. (i) - 3, (ii) - 1, (iii) - 4, (iv) - 2
    3. (i) - 2, (ii) - 4, (iii) - 1, (iv) - 3
    4. (i) - 2, (ii) - 1, (iii) - 4, (iv) - 3
    Show answer

    Answer: (1) (i) - 3, (ii) - 4, (iii) - 1, (iv) - 2

    A topographical survey maps natural features (hills, rivers, forests); a reconnaissance survey is a preliminary look to judge feasibility and rough cost; a cadastral survey fixes property boundaries of fields and houses; an archaeological survey traces relics of antiquity. So i-3, ii-4, iii-1, iv-2.

  9. Q9 · Surveying · Surveying

    Match List - I with List-II and select the correct answer using the codes given below the lists: List - I (Statement) — List - II (Situation) i. Accurate centering in plane table surveying is necessary for — 1. Inaccessible points ii. Exact orientation is more important than accurate centering for — 2. Open country with good intervisibility iii. The intersection method of plane table surveying is particularly employed for — 3. Large scale maps iv. Plane table survey is useful for — 4. Small scale maps Choose the correct option:

    1. (i) - 3, (ii) - 4, (iii) - 1, (iv) - 2
    2. (i) - 4, (ii) - 3, (iii) - 2, (iv) - 1
    3. (i) - 1, (ii) - 2, (iii) - 4, (iv) - 3
    4. (i) - 3, (ii) - 2, (iii) - 1, (iv) - 4
    Show answer

    Answer: (1) (i) - 3, (ii) - 4, (iii) - 1, (iv) - 2

    A centring error shows up on paper only at large scales, so accurate centring matters for large-scale maps, while at small scales orientation matters more. Intersection locates points by rays from two stations without measuring distance, so it suits inaccessible points; plane tabling suits open country with good intervisibility. Hence i-3, ii-4, iii-1, iv-2.

  10. Q10 · Surveying · Surveying

    The following steps are necessary to obtain sufficient accuracy with the tape: I. Keeping uniform tension on tape for each measurement II. "Breaking" tape on slopes are necessary to keep the tape level III. Keeping accurate count of the stations IV. Keeping the tape on the line being measured The correct sequence of these steps is:

    1. IV, II, I, III
    2. II, III, IV, I
    3. IV, I, II, III
    4. III, II, I, IV
    Show answer

    Answer: (1) IV, II, I, III / (3) IV, I, II, III

    Taping starts by holding the tape on the line being measured (IV); it is then pulled with uniform tension (I), held level by breaking the tape on slopes (II), and each tape length is tallied so the count of stations is not lost (III), giving IV, I, II, III. JKSSB's final key accepts both A and C, the two sequences that begin with keeping the tape on line.

  11. Q11 · Mechanics & Structural Analysis · Strength of Materials

    Robert Hooke discovered experimentally that within elastic limit

    1. Stress = strain
    2. Stress × strain = 1
    3. Stress / Strain = a constant
    4. None of the above
    Show answer

    Answer: (3) Stress / Strain = a constant

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  12. Q12 · Mechanics & Structural Analysis · Strength of Materials

    A circular bar is subjected to an axial pull of 100 kN. If the maximum intensity of shear stress on any oblique plane is not to exceed 60 MN/m², determine the diameter of the bar.

    1. 21.6 mm
    2. 32.6 mm
    3. 45.6 mm
    4. 48.6 mm
    Show answer

    Answer: (2) 32.6 mm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  13. Q13 · Mechanics & Structural Analysis · Strength of Materials

    In case of a circular section, the maximum shear stress is ______ percent more than the mean shear stress.

    1. 10
    2. 20
    3. 33.33
    4. 66.66
    Show answer

    Answer: (3) 33.33

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  14. Q14 · Mechanics & Structural Analysis · Strength of Materials

    In a rectangular section, the stress will be of the same sign throughout the section if the load lies within the ______ of the section.

    1. Middle third
    2. Middle half
    3. Both (A) and (B)
    4. None of the above
    Show answer

    Answer: (1) Middle third

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  15. Q15 · Mechanics & Structural Analysis · Strength of Materials

    A cantilever 1.5 m long carries a uniformly distributed load over the entire length. Find the deflection at the free end if the slope at the free end is 1.5°.

    1. 21.88 mm
    2. 29.45 mm
    3. 36.48 mm
    4. 41.54 mm
    Show answer

    Answer: (2) 29.45 mm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  16. Q16 · Mechanics & Structural Analysis · Strength of Materials

    The slope and deflection at a section in a loaded beam can be found out by which of the following methods?

    1. Double integration method
    2. Moment area method
    3. Macaulay's method
    4. Any of the above
    Show answer

    Answer: (4) Any of the above

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  17. Q17 · Mechanics & Structural Analysis · Strength of Materials

    The material that exhibits the same elastic properties in all directions at a point is said to be ______

    1. homogeneous
    2. orthotropic
    3. viscoelastic
    4. isotropic
    Show answer

    Answer: (4) isotropic

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  18. Q18 · Mechanics & Structural Analysis · Strength of Materials

    If principal stresses in a two-dimensional case are −10 MPa and 20 MPa respectively, then maximum shear stress at the point is

    1. 10 MPa
    2. 15 MPa
    3. 20 MPa
    4. 30 MPa
    Show answer

    Answer: (2) 15 MPa

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  19. Q19 · Mechanics & Structural Analysis · Structural Analysis

    All the members of the planar truss (see figure), have the same properties in terms of area of cross-section (A) and modulus of elasticity (E), For the loads shown on the truss, the statements that correctly represents the nature of forces in the members of the truss is:

    Figure for question 19
    1. There are 3 members in tension, and 2 members in compression
    2. There are 2 members in tension, and 2 members in compression, 1 zero-force member
    3. There are 2 members in tension, 1 member in compression, and 2 zero-force members
    4. There are 2 members in tension, and 3 zero-force members
    Show answer

    Answer: (4) There are 2 members in tension, and 3 zero-force members

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  20. Q20 · Mechanics & Structural Analysis · Strength of Materials

    The following statement are related to bending of beams I. The slope of the bending moment diagram is equal to the shear force II. The slope of the shear force diagram is equal to the load intensity III. The slope of the curvature is equal to the flexural rotation IV. The second derivative of the deflection is equal to the curvature The only FALSE statement is

    1. I
    2. II
    3. III
    4. IV
    Show answer

    Answer: (3) III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  21. Q21 · Mechanics & Structural Analysis · Strength of Materials

    A circular solid shaft of span L = 5 m is fixed at one end and free at the other end. A twisting moment T = 100 kN-m is applied at the free end. The torsional rigidity GJ is 50000 kN-m²/rad. Following statements are made for this shaft: 1. The maximum rotation is 0.01 rad 2. The torsional strain energy is 1 kN-m With reference to the above statements, which of the following applies?

    1. Both statements are true
    2. Statement 1 is true but 2 is false
    3. Statement 2 is true but 1 is false
    4. Both statements are false
    Show answer

    Answer: (2) Statement 1 is true but 2 is false

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  22. Q22 · Mechanics & Structural Analysis · Strength of Materials

    Consider the following statements: I. On a principal plane, only normal stress acts II. On a principal plane, both normal and shear stresses act III. On a principal plane, only shear stress acts IV. Isotropic state of stress is independent of frame of reference Which of these statements is/are correct?

    1. I and IV
    2. II only
    3. II and IV
    4. II and III
    Show answer

    Answer: (1) I and IV

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  23. Q23 · Mechanics & Structural Analysis · Strength of Materials

    The "Plane section remain plane" assumption in bending theory implies

    1. Stress profile is linear
    2. Strain profile is linear
    3. Both profiles are linear
    4. Shear deformation is neglected
    Show answer

    Answer: (2) Strain profile is linear

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  24. Q24 · Mechanics & Structural Analysis · Strength of Materials

    List-I shows different loads acting on a beam and List-II shows different bending moment distributions. Match the load with the corresponding bending moment diagram.

    Figure for question 24
    1. A - 4, B - 2, C - 1, D - 3
    2. A - 4, B - 3, C - 1, D - 2
    3. A - 2, B - 3, C - 4, D - 1
    4. None of the above
    Show answer

    Answer: (4) None of the above

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  25. Q25 · Mechanics & Structural Analysis · Strength of Materials

    Four columns of the same material and having identical geometric properties are supported in different ways as shown below: It is required to arrange these four columns in the increasing order of their respective first buckling loads. The correct order is given by

    Figure for question 25
    1. I, II, III, IV
    2. III, IV, I, II
    3. II, I, IV, III
    4. I, II, IV, III
    Show answer

    Answer: (4) I, II, IV, III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  26. Q26 · Hydraulics & Irrigation · Irrigation & Water Resources

    Find the delta for a crop when its duty is 864 hectares/cumec on the field, the base period of this crop is 120 days.

    1. 104 cm
    2. 120 cm
    3. 138 cm
    4. 720 cm
    Show answer

    Answer: (2) 120 cm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  27. Q27 · Hydraulics & Irrigation · Irrigation & Water Resources

    The depth of penetration along the length of a boarder strip at points 30 meters apart were probed. Their observed values are 2.0, 1.9, 1.8, 1.6 and 1.5 meters. Compute the water distribution efficiency.

    1. 0.168
    2. 0.905
    3. 1.760
    4. 2.105
    Show answer

    Answer: (2) 0.905

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  28. Q28 · Hydraulics & Irrigation · Irrigation & Water Resources

    A tile drainage system draining 12 hectares, flows at a design capacity for two days, following a storm. If the system is designed using a drainage coefficient of 1.25 cm, how many cubic meters of water will be removed during this period?

    1. 1000 m³
    2. 2000 m³
    3. 3000 m³
    4. 4000 m³
    Show answer

    Answer: (3) 3000 m³

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  29. Q29 · Hydraulics & Irrigation · Irrigation & Water Resources

    The recharging rate of ground water depends upon ______ and on the depth of water stored, and is generally less.

    1. the permeability of the spread area
    2. Renney type wells
    3. Infiltration tube springs
    4. None of the above
    Show answer

    Answer: (1) the permeability of the spread area

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  30. Q30 · Hydraulics & Irrigation · Irrigation & Water Resources

    The lake of water which is formed upstream is often called a ______

    1. creep
    2. reservoir
    3. side flanks
    4. swift trinity
    Show answer

    Answer: (2) reservoir

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  31. Q31 · Hydraulics & Irrigation · Irrigation & Water Resources

    The following statements are related to cross drainage works and their types. Statement - 1: The culvert length or width of aqueduct is maximum in Type I and minimum in Type III. An intermediate value exists in Type II. Statement - 2: In Type III, earthen section of the canal is discontinued and the canal water is carried in a masonry or a flumed in this case. Choose the correct option:

    1. Statement 1 is correct and Statement 2 is incorrect
    2. Statement 2 is correct and Statement 1 is incorrect
    3. Statement 1 and 2 are correct
    4. Statement 1 and 2 are incorrect
    Show answer

    Answer: (3) Statement 1 and 2 are correct

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  32. Q32 · Hydraulics & Irrigation · Irrigation & Water Resources

    Consider the following Statements: Statement - 1: The length of the guide bank on the downstream side should be between 0.1 L to 0.2 L. L indicates the length of structure between the abutments. Statement - 2: The top level of guide banks is governed by HFL, afflux, velocity head and freeboard. It can be obtained by adding all these four values. Choose the correct option:

    1. Statement 1 is correct and Statement 2 is incorrect
    2. Statement 2 is correct and Statement 1 is incorrect
    3. Statement 1 and 2 are correct
    4. Statement 1 and 2 are incorrect
    Show answer

    Answer: (3) Statement 1 and 2 are correct

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  33. Q33 · Hydraulics & Irrigation · Irrigation & Water Resources

    The drainage water intercepting the canal can be disposed in different ways. And the type of cross-drainage works with their function is given below. Match List - I with List-II and select the correct answer using the codes given below the lists: List - I (Function/Places) — List - II (Accomplished) 1. By passing the canal over the drainage — i. Either through a level crossing or through inlets and outlets 2. By passing the canal below the drainage — ii. Either through a super-passage or through a canal syphon 3. By passing the drain through a canal — iii. Either through an aqueduct or through a syphon-aqueduct Choose the correct option:

    1. (1)-i, (2)-ii, (3)-iii
    2. (1)-ii, (2)-iii, (3)-i
    3. (1)-iii, (2)-i, (3)-ii
    4. (1)-iii, (2)-ii, (3)-i
    Show answer

    Answer: (4) (1)-iii, (2)-ii, (3)-i

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  34. Q34 · Hydraulics & Irrigation · Irrigation & Water Resources

    Match List - I with List-II and select the correct answer using the codes given below the lists: List-I (Classification of River Training) — List - II (Purpose) 1. High water training — i. Sediment (efficient disposal of suspended load and bed load) 2. Low water training — ii. Discharge (flood control) 3. Mean water training — iii. Depth (provide sufficient water depth) Choose the correct option:

    1. (1)-i, (2)-ii, (3)-iii
    2. (1)-ii, (2)-iii, (3)-i
    3. (1)-iii, (2)-i, (3)-ii
    4. (1)-iii, (2)-ii, (3)-i
    Show answer

    Answer: (2) (1)-ii, (2)-iii, (3)-i

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  35. Q35 · Hydraulics & Irrigation · Irrigation & Water Resources

    ______(i)______ evaporates water, and ______(ii)______, by causing and controlling winds, circulates the evaporated water vapour, and thus, helping in its ______(iii)______ at different places. Choose the correct option to fill out i, ii, iii in order.

    1. Sun, hydro cycle, filtration
    2. Sun, Coriolis force, filtration
    3. Sun, cycle, precipitation
    4. Sun, Coriolis force, reprecipitation
    Show answer

    Answer: (4) Sun, Coriolis force, reprecipitation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  36. Q36 · Environmental Engineering · Water Supply & Sanitary Engineering

    In a domestic wastewater sample, COD and BOD were measured. Generally, which of the following statement is true for their relative magnitude?

    1. COD = BOD
    2. COD > BOD
    3. COD < BOD
    4. None of the above
    Show answer

    Answer: (2) COD > BOD

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  37. Q37 · Environmental Engineering · Water Supply & Sanitary Engineering

    The portable water is prepared from turban surface water by adopting the following treatment sequence.

    1. Turbid surface water - Coagulation - Flocculation - Sedimentation - Filtration - Disinfection - Storage and Supply
    2. Turbid surface water - Sedimentation - Coagulation - Flocculation - Filtration - Disinfection - Storage and Supply
    3. Turbid surface water - Flocculation - Coagulation - Filtration - Disinfection - Sedimentation - Storage and Supply
    4. Turbid surface water - Coagulation - Flocculation - Filtration - Disinfection - Sedimentation - Storage and Supply
    Show answer

    Answer: (1) Turbid surface water - Coagulation - Flocculation - Sedimentation - Filtration - Disinfection - Storage and Supply

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  38. Q38 · Environmental Engineering · Water Supply & Sanitary Engineering

    A 1% solution of sewage sample is incubated for 5 days at 20°C. The depletion of oxygen was found to be 3ppm. Determine the BOD of raw sewage.

    1. 60 ppm
    2. 150 ppm
    3. 300 ppm
    4. 600 ppm
    Show answer

    Answer: (3) 300 ppm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  39. Q39 · Environmental Engineering · Water Supply & Sanitary Engineering

    As per Noise Pollution (Regulation and Control) Rules 2000 of India, the day time noise limit for a residential zone, expressed in dB (A) Leq, is

    1. 45
    2. 55
    3. 65
    4. 75
    Show answer

    Answer: (2) 55

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  40. Q40 · Building Materials & Construction · Building Construction

    When the depth of trench exceeds 1.5 to 2m, and when excavations is made with side vertical, it becomes necessary to support the side by sheeting and bracing. This operation is known as ______

    1. shafts of trench
    2. electro-osmosis
    3. boning of trench
    4. timbering of trench
    Show answer

    Answer: (4) timbering of trench

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  41. Q41 · Environmental Engineering · Water Supply & Sanitary Engineering

    The following two statements are relevant to method of sewage disposal. Statement - 1: The three principal processes of land treatment of wastewater are (i) Broad irrigation or sewage farming, (ii) Rapid infiltration, and (iii) Overland runoff. Statement - 2: The ratio of quantity of receiving water to that of wastewater or effluent discharge is called the dilution factor. Choose the correct option:

    1. Statement 1 is correct and Statement 2 is incorrect
    2. Statement 2 is correct and Statement 1 is incorrect
    3. Statement 1 and 2 are correct
    4. Statement 1 and 2 are incorrect
    Show answer

    Answer: (3) Statement 1 and 2 are correct

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  42. Q42 · Environmental Engineering · Water Supply & Sanitary Engineering

    Match List - I with List-II and select the correct answer using the codes given below the lists: List - I (Water properties) — List - II (Titrants) i. Alkalinity — 1. N/35.5 AgNO₃ ii. Hardness — 2. N/40 Na₂S₂O₃ iii. Chlorine — 3. N/50 H₂SO₄ iv. Dissolved Oxygen — 4. N/50 EDTA Choose the correct option:

    1. (i) - 2, (ii) - 4, (iii) - 3, (iv) - 1
    2. (i) - 3, (ii) - 4, (iii) - 1, (iv) - 2
    3. (i) - 1, (ii) - 2, (iii) - 4, (iv) - 3
    4. (i) - 4, (ii) - 3, (iii) - 2, (iv) - 1
    Show answer

    Answer: (2) (i) - 3, (ii) - 4, (iii) - 1, (iv) - 2

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  43. Q43 · Environmental Engineering · Water Supply & Sanitary Engineering

    Match List - I with List-II and select the correct answer using the codes given below the lists: List - I (Materials and Air pollutants) — List - II (Effects) 1. Materials: Metals; and Pollutants: SO₂ — i. Embrittlement 2. Materials: Paper; and Pollutants: SO₂ — ii. Reduction in tensile strength 3. Materials: Textiles; and Pollutants: SO₂ — iii. Tarnishing of surfaces Choose the correct option:

    1. (1)-i, (2)-ii, (3)-iii
    2. (1)-ii, (2)-iii, (3)-i
    3. (1)-iii, (2)-i, (3)-ii
    4. (1)-iii, (2)-ii, (3)-i
    Show answer

    Answer: (3) (1)-iii, (2)-i, (3)-ii

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  44. Q44 · Environmental Engineering · Water Supply & Sanitary Engineering

    Match List - I with List-II and select the correct answer using the codes given below the lists: List - I (Type of water impurity) — List - II (Method of treatment) i. Hardness — 1. Reverse Osmosis ii. Brackish water from sea — 2. Chlorination iii. Residual MPN from filters — 3. Zeolite treatment iv. Turbidity — 4. Coagulation, Flocculation and Filtration Choose the correct option:

    1. (i) - 1, (ii) - 4, (iii) - 3, (iv) - 2
    2. (i) - 4, (ii) - 3, (iii) - 1, (iv) - 2
    3. (i) - 2, (ii) - 1, (iii) - 4, (iv) - 3
    4. (i) - 3, (ii) - 1, (iii) - 2, (iv) - 4
    Show answer

    Answer: (4) (i) - 3, (ii) - 1, (iii) - 2, (iv) - 4

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  45. Q45 · Environmental Engineering · Water Supply & Sanitary Engineering

    Particles may settle out of a suspension in four ways, depending upon the concentration of the suspension and the flocculating properties of the particles. Arrange the four types in order with respect to decreasing of settling depth vs increasing of settling time. Choose the correct order.

    1. Discreate settling, Flocculant settling, Zone settling, Compression settling
    2. Compression settling, Flocculant settling, Discreate settling, Zone settling
    3. Zone settling, Flocculant settling, Discreate settling, Compression settling
    4. Discreate settling, Zone settling, Flocculant settling, Compression settling
    Show answer

    Answer: (1) Discreate settling, Flocculant settling, Zone settling, Compression settling

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  46. Q46 · Building Materials & Construction · Building Materials

    Gap grading of aggregate is one, in which

    1. At least one intermediate aggregate fraction is absent
    2. % passing fall within a narrow limit of size fractions
    3. Combines different fractions of fine and coarse aggregates
    4. All the aggregate are of same size
    Show answer

    Answer: (1) At least one intermediate aggregate fraction is absent

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  47. Q47 · RCC & Steel Design · RCC Design

    As per limit state design method the ultimate strain in the outermost compression fiber of concrete in bending is taken as

    1. 0.0020
    2. 0.0120
    3. 0.0035
    4. 0.0520
    Show answer

    Answer: (3) 0.0035

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  48. Q48 · Mechanics & Structural Analysis · Engineering Mechanics

    A frame having (M) number of member and joints (J) is said to be perfect frame if it follows the equation as given below

    1. J = 2M − 3
    2. M = 2J − 3
    3. M = 3J − 2
    4. J = M + 3
    Show answer

    Answer: (2) M = 2J − 3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  49. Q49 · Mechanics & Structural Analysis · Strength of Materials

    Consider the following pairs, for a cantilever beam of length (l), loaded by point load (w) and flexural rigidity (EI). i. Maximum Bending Moment — 1. wl ii. Strain Energy — 2. wl²/2EI iii. Maximum slop — 3. wl³/3EI iv. Maximum deflection — 4. w²l³/6EI Which of the pair given below is correctly matched?

    1. (i)-(1), (ii)-(4), (iii)-(3), (iv)-(2)
    2. (i)-(1), (ii)-(4), (iii)-(2), (iv)-(3)
    3. (i)-(4), (ii)-(2), (iii)-(1), (iv)-(3)
    4. (i)-(4), (ii)-(3), (iii)-(1), (iv)-(2)
    Show answer

    Answer: (2) (i)-(1), (ii)-(4), (iii)-(2), (iv)-(3)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  50. Q50 · Building Materials & Construction · Building Materials

    The constituent compounds of cement in decreasing order of rate of hydration are

    1. C₂S, C₃S and C₃A
    2. C₃S, C₃A and C₂S
    3. C₃A, C₂S and C₃S
    4. C₃A, C₃S and C₂S
    Show answer

    Answer: (4) C₃A, C₃S and C₂S

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  51. Q51 · Mechanics & Structural Analysis · Structural Analysis

    Which of the following Indian Standard (IS) code used for wind load analysis for designing building structure

    1. IS 456
    2. IS 800
    3. IS 875
    4. IS 1893
    Show answer

    Answer: (3) IS 875

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  52. Q52 · RCC & Steel Design · RCC Design

    In a cantilever RCC beam design, tensile reinforcement is provided

    1. On the top of the beam
    2. On the bottom of the beam
    3. In the middle of the beam
    4. On the top and bottom of the beam
    Show answer

    Answer: (1) On the top of the beam

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  53. Q53 · Building Materials & Construction · Building Materials

    For construction of structure under water the type of lime used is

    1. Hydraulic lime
    2. Fat lime
    3. Quick lime
    4. Pure lime
    Show answer

    Answer: (1) Hydraulic lime

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  54. Q54 · Building Materials & Construction · Building Materials

    The standard size of the brick as per IS standard is

    1. 10 × 9 × 9 cm
    2. 18 × 9 × 9 cm
    3. 19 × 9 × 9 cm
    4. 23 × 12 × 8 cm
    Show answer

    Answer: (3) 19 × 9 × 9 cm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  55. Q55 · Building Materials & Construction · Building Materials

    Inadequate compaction during concrete casting results in

    1. Segregation
    2. Rutting
    3. Bleeding
    4. Honey combing
    Show answer

    Answer: (4) Honey combing

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  56. Q56 · RCC & Steel Design · RCC Design

    Side face reinforcement is required when the depth of the web of a beam is

    1. Greater than 750 mm
    2. Greater than 900 mm
    3. Greater than 950 mm
    4. Greater than 1000 mm
    Show answer

    Answer: (1) Greater than 750 mm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  57. Q57 · Mechanics & Structural Analysis · Strength of Materials

    Distribution of shear stress intensity over a rectangular section of a loaded beam follows diagrammatically

    1. A circular curve
    2. A straight line
    3. A parabolic curve
    4. An elliptical curve
    Show answer

    Answer: (3) A parabolic curve

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  58. Q58 · Building Materials & Construction · Building Materials

    The compressive strength of 100 mm cube as compared to 150 mm cube is always

    1. More
    2. Less
    3. Same
    4. Unpredictable
    Show answer

    Answer: (1) More

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  59. Q59 · Building Materials & Construction · Building Materials

    Which of the following is a tensile test of a cylindrical concrete sample,

    1. Compaction factor test
    2. Le Chatelier's test
    3. Splitting test
    4. Autoclave test
    Show answer

    Answer: (3) Splitting test

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  60. Q60 · RCC & Steel Design · RCC Design

    The main reinforcement of a RC slab consists of 6 mm bars at 10 cm spacing if it is desired to replace 6 mm bars by 12 mm bars, then spacing of 12 mm bars should be

    1. 10 cm
    2. 40 cm
    3. 60 cm
    4. 120 cm
    Show answer

    Answer: (2) 40 cm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  61. Q61 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    The void ratio of a fully saturated soil sample having a porosity of 0.3 is

    1. 0.26
    2. 0.66
    3. 0.43
    4. 1.0
    Show answer

    Answer: (3) 0.43

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  62. Q62 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    The soil has a bulk density of 55 kN/m³ and water content 10%. The dry density of soil is

    1. 5.5 kN/m³
    2. 10 kN/m³
    3. 50 kN/m³
    4. 55 kN/m³
    Show answer

    Answer: (3) 50 kN/m³

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  63. Q63 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    Lime stabilization is very effective in treating

    1. Sandy soil
    2. Silty soil
    3. Non-plastic soil
    4. Plastic clayey soil
    Show answer

    Answer: (4) Plastic clayey soil

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  64. Q64 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    Soil which contains finest grain particles

    1. Fine sand
    2. Sand
    3. Clay
    4. Silt
    Show answer

    Answer: (3) Clay

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  65. Q65 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    The minimum water content at which the soil just begins to crumble when rolled into threads of 3 mm in diameter, is known as

    1. Liquid limit
    2. Plastic limit
    3. Shrinkage limit
    4. Permeability limit
    Show answer

    Answer: (2) Plastic limit

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  66. Q66 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    Consider soil as a three-phase system, the ratio of (Liquid Limit − Natural water Content)/Plasticity index for the soil mass is called

    1. Liquidity index
    2. Shrinkage ratio
    3. Consistency index
    4. Toughness index
    Show answer

    Answer: (3) Consistency index

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  67. Q67 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    Which of the following is a measure of particle size range?

    1. Effective size
    2. Uniformity coefficient
    3. Effective diameter
    4. Elongation index
    Show answer

    Answer: (2) Uniformity coefficient

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  68. Q68 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    From a laboratory proctor compaction test data, the mass of the soil and water content is found to be 1100 g and 10% respectively. The volume of the proctor mould used is 1000 cm³, then the dry density (γd) of the soil is

    1. 1 g/cm³
    2. 1.10 g/cm³
    3. 1.50 g/cm³
    4. 1.15 g/cm³
    Show answer

    Answer: (1) 1 g/cm³

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  69. Q69 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    In an unconfined compression test, a saturated clay sample, fails under a load of 150N. Consider final cross-section area (Af) = 2250 mm². Then the shear resistance (cohesion) of the sample is

    1. 66.21 kPa
    2. 34.95 kPa
    3. 33.33 kPa
    4. 15 kPa
    Show answer

    Answer: (3) 33.33 kPa

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  70. Q70 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    Consider the following pairs i. Standard Proctor Test — 1. [C, φ], apparent cohesion and angle of internal friction ii. Modified Proctor Test — 2. 03 layers, 310 mm height of drop iii. Direct Shear Test — 3. 05 layers, 450 mm height of drop iv. Triaxial Test — 4. [C′, φ′], strength parameter Which of the pair given below is correctly matched?

    1. (i)-(1), (ii)-(2), (iii)-(4), (iv)-(3)
    2. (i)-(2), (ii)-(3), (iii)-(1), (iv)-(4)
    3. (i)-(3), (ii)-(2), (iii)-(1), (iv)-(4)
    4. (i)-(4), (ii)-(3), (iii)-(1), (iv)-(2)
    Show answer

    Answer: (2) (i)-(2), (ii)-(3), (iii)-(1), (iv)-(4)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  71. Q71 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    A fluid is said to be Newtonian fluid when its shear stress is

    1. Inversely proportional to the velocity gradient
    2. Proportional to the velocity gradient
    3. Independent to the velocity gradient
    4. Inversely proportional to the shear stress rate
    Show answer

    Answer: (2) Proportional to the velocity gradient

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  72. Q72 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    Pascal-second (Pa.s) is the unit of

    1. Pressure
    2. Specific gravity
    3. Dynamic viscosity
    4. Compressibility
    Show answer

    Answer: (3) Dynamic viscosity

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  73. Q73 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    If specific gravity of a fluid is 0.5, and dynamic viscosity is 0.5 poise, then the kinematic viscosity of that fluid is

    1. 0.25 stokes
    2. 0.50 stokes
    3. 1.0 stokes
    4. 25 stokes
    Show answer

    Answer: (3) 1.0 stokes

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  74. Q74 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    A uniformly tapering vessel is filled with liquid of density 900 kg/m³. Then the force that act on the base of the vessel due to the liquid (g = 10 m/sec²) is

    Figure for question 74
    1. 3.6 N
    2. 7.2 N
    3. 9.8 N
    4. 15.4 N
    Show answer

    Answer: (2) 7.2 N

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  75. Q75 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    The velocity of the upper layer of water in a river is 36 km h⁻¹. Shearing stress between horizontal layers of water is 10⁻³ Nm⁻². Consider co-efficient of viscosity of water is 10⁻² Pa-s. Then depth of the river is

    1. 100 m
    2. 200 m
    3. 360 m
    4. 3600 m
    Show answer

    Answer: (1) 100 m

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  76. Q76 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    Open tank contains 1 m deep water with 50 cm depth of oil of specific gravity 0.6 above it, then the intensity of pressure at the bottom of tank is (taken, g = 1000 cm s⁻²)

    1. 3 kN/m²
    2. 13 kN/m²
    3. 30 kN/m²
    4. 40 kN/m²
    Show answer

    Answer: (2) 13 kN/m²

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  77. Q77 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    The following figure shows a venturimeter, through which water is flowing. The speed of water at "X" is 2 cm s⁻¹ and height difference between "X" and "Y" is 5.1 mm. Then the speed of water at "Y" is (taken, g = 1000 cm s⁻²)

    Figure for question 77
    1. 23 cm s⁻¹
    2. 32 cm s⁻¹
    3. 101 cm s⁻¹
    4. 1024 cm s⁻¹
    Show answer

    Answer: (2) 32 cm s⁻¹

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  78. Q78 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    An open tank filled with water (density = ρ and g = 9.81 m/sec²) has a narrow hole at a depth of "h" below the water surface. Then the velocity of water flowing out is

    1. √(2gh)
    2. ρgh
    3. 2 gh
    4. gh
    Show answer

    Answer: (1) √(2gh)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  79. Q79 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    The Reynold's number for fluid flow in a pipe is independent of

    1. The viscosity of the fluid
    2. The velocity of the fluid
    3. The length of the pipe
    4. The diameter of the pipe
    Show answer

    Answer: (3) The length of the pipe

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  80. Q80 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    The point in the immerse body through which the resultant of the total pressure of the liquid be taken to act is known as

    1. Metacenter
    2. Centre of gravity
    3. Centre of buoyancy
    4. Centre of pressure
    Show answer

    Answer: (4) Centre of pressure

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  81. Q81 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    Bernouli's principle is derived from the law of conservation of

    1. Energy
    2. Mass
    3. Linear momentum
    4. Angular momentum
    Show answer

    Answer: (1) Energy

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  82. Q82 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    If a mercury droop is divided into 8 equal parts, then it’s total energy

    1. Remains same
    2. Becomes twice
    3. Decreases by a factor of 8
    4. Increases by a factor of 8
    Show answer

    Answer: (2) Becomes twice

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  83. Q83 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    The continuity equation is based on which of the following principle

    1. Conservation of mass
    2. Conservation of static energy
    3. Conservation of kinetic energy
    4. Conservation of momentum
    Show answer

    Answer: (1) Conservation of mass

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  84. Q84 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    The major causes for the loss of energy in long pipe is due to

    1. Sudden contraction
    2. Sudden enlargement
    3. Loss at the exit of the pipe
    4. Friction in the pipe
    Show answer

    Answer: (4) Friction in the pipe

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  85. Q85 · Hydraulics & Irrigation · Fluid Mechanics & Hydraulics

    Consider the following pairs i. Pitot tube — 1. Flow and viscous property of fluid ii. Rheometer — 2. Flowing fluid velocity at any point iii. Hydrometer — 3. Pressure of the pipeline iv. Manometer — 4. Specific gravity or density of a liquid Which of the pair given below is correctly matched?

    1. (i)-(1), (ii)-(2), (iii)-(3), (iv)-(4)
    2. (i)-(1), (ii)-(4), (iii)-(3), (iv)-(2)
    3. (i)-(2), (ii)-(1), (iii)-(4), (iv)-(3)
    4. (i)-(4), (ii)-(3), (iii)-(2), (iv)-(1)
    Show answer

    Answer: (3) (i)-(2), (ii)-(1), (iii)-(4), (iv)-(3)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  86. Q86 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    If N = Number of layers, W = Weight of the hammer, H = Height of fall, then which of the following option is correct for California Bearing Ratio (CBR) Test using heavy compaction?

    1. N = 3, W = 4.89 kg and H = 31 cm
    2. N = 3, W = 4.89 kg and H = 45 cm
    3. N = 5, W = 4.89 kg and H = 45 cm
    4. N = 5, W = 4.89 kg and H = 31 cm
    Show answer

    Answer: (3) N = 5, W = 4.89 kg and H = 45 cm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  87. Q87 · Soil Mechanics & Foundations · Soil Mechanics & Foundations

    The coefficient of uniformity is defined as

    1. Cu = D₃₀/D₁₀
    2. Cu = D₆₀/D₁₀
    3. Cu = [D₃₀]²/D₁₀
    4. Cu = D₃₀/(D₁₀ × D₆₀)
    Show answer

    Answer: (2) Cu = D₆₀/D₁₀

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  88. Q88 · Transportation Engineering · Highway Engineering

    For a vehicle negotiating a curve, centrifugal force "P", is i. Directly proportional to the weight of vehicle ii. Inversely proportional to square of velocity iii. Inversely proportional to radius of curve Which of the above statements are true?

    1. (i) and (ii)
    2. (ii) and (iii)
    3. (i) and (iii)
    4. (i), (ii) and (iii)
    Show answer

    Answer: (3) (i) and (iii)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  89. Q89 · Transportation Engineering · Highway Engineering

    The penetration test of bitumen is conducted at X, measuring the penetration of needle loaded with Y load for Z time. The correct values are

    1. X = 25°C; Y = 100 gm; Z = 5 sec
    2. X = 25°C; Y = 100 gm; Z = 10 sec
    3. X = 27°C; Y = 50 gm; Z = 60 sec
    4. X = 27°C; Y = 100 gm; Z = 10 sec
    Show answer

    Answer: (1) X = 25°C; Y = 100 gm; Z = 5 sec

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  90. Q90 · Transportation Engineering · Highway Engineering

    For carrying out bituminous patch work during rainy season, the most suitable binder is

    1. Bitumen
    2. Bituminous emulsion
    3. Cutback bitumen
    4. Road tar
    Show answer

    Answer: (2) Bituminous emulsion

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  91. Q91 · Transportation Engineering · Highway Engineering

    Pick the right sequence of the different layers of a flexible pavement construction i. Base course construction ii. Subbase course construction iii. Surface course and seal coat application iv. Natural subgrade and compacted subgrade construction v. Prime coat, binder course and tack coat application Choose the correct answer from the options given below

    1. (i), (ii), (iii), (iv), (v)
    2. (i), (iii), (v), (ii), (iv)
    3. (iv), (ii), (i), (v), (iii)
    4. (iv), (v), (i), (ii), (iii)
    Show answer

    Answer: (3) (iv), (ii), (i), (v), (iii)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  92. Q92 · Transportation Engineering · Highway Engineering

    Alligator or map cracking is the most common type of failure in

    1. Bituminous surfacing
    2. Water Bound Macadam (WBM) surfacing
    3. Wet Mix Macadam (WMM) surfacing
    4. Telford and Macadam surfacing
    Show answer

    Answer: (1) Bituminous surfacing

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  93. Q93 · Transportation Engineering · Highway Engineering

    A vehicle was stopped in 2 second by fully jamming the break and skid marks measured 20 m then average skid resistance is (consider g = 10 m/sec²)

    1. 0.35
    2. 0.50
    3. 1.0
    4. 2.2
    Show answer

    Answer: (3) 1.0

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  94. Q94 · Transportation Engineering · Highway Engineering

    The wall which are necessary on the hill side of roadway where natural earth has to be retained from sliding is known as

    1. Retaining wall
    2. Breast wall
    3. Parapet wall
    4. Cavity wall
    Show answer

    Answer: (2) Breast wall

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  95. Q95 · Transportation Engineering · Highway Engineering

    Consider the following pairs i. Los angeles abrasion — 1. Gradation ii. Size — 2. Toughness iii. Durability — 3. Hardness iv. Impact — 4. Soundness Which of the pair given below is correctly matched?

    1. (i)-(2), (ii)-(1), (iii)-(3), (iv)-(4)
    2. (i)-(2), (ii)-(4), (iii)-(3), (iv)-(1)
    3. (i)-(3), (ii)-(1), (iii)-(4), (iv)-(2)
    4. (i)-(3), (ii)-(4), (iii)-(1), (iv)-(2)
    Show answer

    Answer: (3) (i)-(3), (ii)-(1), (iii)-(4), (iv)-(2)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  96. Q96 · Transportation Engineering · Highway Engineering

    The fundamental relationship between space-mean speed (u), traffic density (k) and traffic flow (q) is

    1. q = u × k
    2. q = u/k
    3. q = k/u
    4. q = k²/u
    Show answer

    Answer: (1) q = u × k

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  97. Q97 · Transportation Engineering · Railways, Bridges & Other Transport

    Which of the following rails is most preferred by Indian railway

    1. Flat footed rails
    2. Bull head rails
    3. Double headed rails
    4. Thin headed rails
    Show answer

    Answer: (1) Flat footed rails

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  98. Q98 · Transportation Engineering · Railways, Bridges & Other Transport

    Gauge is the horizontal distance measured between

    1. Centre to center of two rails
    2. Inner or running faces of two rails
    3. Outer to inner face of two rails
    4. Inner to Outer face of two rails
    Show answer

    Answer: (2) Inner or running faces of two rails

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  99. Q99 · Transportation Engineering · Railways, Bridges & Other Transport

    Two major constituents in the composition of steel used in rail are

    1. Carbon and Silicon
    2. Carbon and Sulphur
    3. Carbon and Manganese
    4. Carbon and Lithium
    Show answer

    Answer: (3) Carbon and Manganese

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  100. Q100 · Transportation Engineering · Railways, Bridges & Other Transport

    The rising gradient on which a moving train takes the advantage of the preceding falling gradient, usually referred as

    1. Pusher gradient
    2. Neutral gradient
    3. Ruling gradient
    4. Momentum gradient
    Show answer

    Answer: (4) Momentum gradient

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  101. Q101 · Transportation Engineering · Railways, Bridges & Other Transport

    The longitudinally movement of rails in a track is technically referred as,

    1. Hogging
    2. Buckling
    3. Creeping
    4. Tilting
    Show answer

    Answer: (3) Creeping

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  102. Q102 · Transportation Engineering · Railways, Bridges & Other Transport

    The sleeping of driving wheels of locomotives on the rail surface causes,

    1. Wheel burns
    2. Hogging of rail
    3. Corrugation of rail
    4. Buckling of rail
    Show answer

    Answer: (1) Wheel burns

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  103. Q103 · Transportation Engineering · Railways, Bridges & Other Transport

    The wear of the rail is maximum at

    1. Tunnel
    2. Sharp curve
    3. Coastal area
    4. Square crossing
    Show answer

    Answer: (2) Sharp curve

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  104. Q104 · Transportation Engineering · Railways, Bridges & Other Transport

    Which among the following organization is the Research and Development (R&D) wing of Indian Railways

    1. IRCTC
    2. DRDO
    3. RDSO
    4. CRIS
    Show answer

    Answer: (3) RDSO

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  105. Q105 · Transportation Engineering · Railways, Bridges & Other Transport

    Consider the following pairs i. Ballast — 1. Rail fastenings with concrete sleeper ii. Sleeper — 2. To hold the rail in proper gauge iii. Jim crow — 3. To bend the rail iv. Pandrol clip — 4. To Provide cushion effect to the track Which of the pair given below is correctly matched?

    1. (i)-(2), (ii)-(1), (iii)-(3), (iv)-(4)
    2. (i)-(2), (ii)-(4), (iii)-(3), (iv)-(1)
    3. (i)-(3), (ii)-(1), (iii)-(4), (iv)-(2)
    4. (i)-(4), (ii)-(2), (iii)-(3), (iv)-(1)
    Show answer

    Answer: (4) (i)-(4), (ii)-(2), (iii)-(3), (iv)-(1)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  106. Q106 · Building Materials & Construction · Building Construction

    What is the portion of a brick obtained by cutting the brick longitudinally into two equal parts?

    1. Queen closer
    2. King closer
    3. Half bat
    4. Bewelled closer
    Show answer

    Answer: (1) Queen closer

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  107. Q107 · Estimating & Construction Management · Estimating & Costing

    In long and short wall method of estimation, the length of long wall is the center to center distance between the wall and

    1. breadth of the wall
    2. half breadth of the wall on each side
    3. one forth breadth of the wall on each side
    4. one fifth breadth of the wall on each side
    Show answer

    Answer: (2) half breadth of the wall on each side

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  108. Q108 · Estimating & Construction Management · Estimating & Costing

    The Damp Proof Course (D.P.C) is measure in

    1. Cubic meter
    2. Square meter
    3. Meters
    4. Rupees per meter
    Show answer

    Answer: (2) Square meter

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  109. Q109 · Estimating & Construction Management · Estimating & Costing

    While submitting a tender the contractor is required to deposit some amount with the department, as guarantee of the tender, known as

    1. Bank guarantee
    2. Caution money
    3. Security deposit
    4. Earnest money
    Show answer

    Answer: (4) Earnest money

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  110. Q110 · Estimating & Construction Management · Estimating & Costing

    Estimated value of a built up property at the end of its useful life without being dismantled is known as,

    1. Scrap value
    2. Salvage Value
    3. Market value
    4. Book value
    Show answer

    Answer: (2) Salvage Value

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  111. Q111 · Estimating & Construction Management · Construction Management

    In a network diagram, an activity having a dotted arrow between two activity is referred as,

    1. Important activity
    2. Risky activity
    3. Dummy activity
    4. Delayed activity
    Show answer

    Answer: (3) Dummy activity

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  112. Q112 · Estimating & Construction Management · Construction Management

    In the following network, choose the Critical Path from given options, (the number on the arrow shows duration of activity) The correct option is:

    Figure for question 112
    1. A - B - C - D - E - F
    2. A - B - D - E - F
    3. A - B - C - E - F
    4. A - B - D - C - E - F
    Show answer

    Answer: (1) A - B - C - D - E - F

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  113. Q113 · Estimating & Construction Management · Construction Management

    If the optimistic time (tₒ), most likely or probable time (tₘ), and pessimistic time (tₚ), for activity (A) are 2, 5 and 14 days respectively, then expected duration and variance of the activity are

    1. 2 and 5 days
    2. 6 and 4 days
    3. 14 and 7 days
    4. 16 and 5 days
    Show answer

    Answer: (2) 6 and 4 days

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  114. Q114 · Estimating & Construction Management · Construction Management

    As per Critical Path Methodology (CPM) the earliest start time for an event (I) is 10 weeks. Activity (I-J) takes 4 weeks for completion. Event (J) starts after 20 weeks. Then the total float for activity (I-J) is,

    1. 2 weeks
    2. 6 weeks
    3. 12 weeks
    4. 16 weeks
    Show answer

    Answer: (2) 6 weeks

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  115. Q115 · Estimating & Construction Management · Construction Management

    The difference between Late Start and Early Start Time of an activity is referred as,

    1. Float
    2. Progress of an activity
    3. Task of a work
    4. PERT task
    Show answer

    Answer: (1) Float

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  116. Q116 · Estimating & Construction Management · Construction Management

    A scheduled activity may begin 10 days before the predecessor activity finishes. Then it's referred as an example of,

    1. Finish to start
    2. Finish to finish
    3. Start to finish
    4. Start to start
    Show answer

    Answer: (1) Finish to start

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  117. Q117 · Estimating & Construction Management · Construction Management

    Following is a Rate list for an earth excavation work:

    S.NoItem : earth workRateVariable rate
    IManual excavationRs.10 /cumNil
    IIMachine excavationRs. 4000 fixedRs.2 /cum

    As per above rate list, estimated quantity of earth, for which the cost of excavation by machine will be equal to the cost of manual excavation, considering variable rate is

    1. 500 cum
    2. 1000 cum
    3. 2500 cum
    4. 3000 cum
    Show answer

    Answer: (1) 500 cum

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  118. Q118 · Estimating & Construction Management · Construction Management

    The cost slop is defined as

    1. (Crash cost - Normal cost)/Normal time
    2. (Crash cost - Normal cost)/Crash time
    3. Crash cost/(Normal time-Crash time)
    4. (Crash cost-Normal cost)/(Normal time-Crash time)
    Show answer

    Answer: (4) (Crash cost-Normal cost)/(Normal time-Crash time)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  119. Q119 · Estimating & Construction Management · Construction Management

    Which among the following, means statistical quality control of RCC work at civil construction site?

    1. Minimizing cost for removal of defective work
    2. Appling theory of probability to sample testing or inspection
    3. Minimizing in wastage of inspection cost
    4. Calculating risk probably to minimize utilization
    Show answer

    Answer: (2) Appling theory of probability to sample testing or inspection

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  120. Q120 · Estimating & Construction Management · Construction Management

    Consider the following pairs i. Net working — 1. actual performance of the task and consume time or resources, represented by an arrow ii. Activity — 2. an arrow diagram obtained by connecting all the activities of a project in a logical sequence iii. Event — 3. sequential relationship between other activities but does not consume resources, and represented by a circle iv. Dummy activity — 4. start or completion of tasks and does not consume time or resources, and represent precedence relationship between real activities. Which of the pair given below is correctly matched

    1. (i)-(2), (ii)-(1), (iii)-(3), (iv)-(4)
    2. (i)-(2), (ii)-(4), (iii)-(3), (iv)-(1)
    3. (i)-(3), (ii)-(1), (iii)-(4), (iv)-(2)
    4. (i)-(3), (ii)-(4), (iii)-(1), (iv)-(2)
    Show answer

    Answer: (1) (i)-(2), (ii)-(1), (iii)-(3), (iv)-(4)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.