Learn with Anil · JKSSB JE Civil PYQsPractise online →Subscribe ₹149

JKSSB JE Civil Mechanics & Structural Analysis previous year questions with answers

Every Mechanics & Structural Analysis question asked in the JKSSB JE Civil papers on this site, grouped by topic. Answers come from JKSSB's key; each has a short explanation (free here for a sample, all of them in the practice app).

Practise Mechanics & Structural Analysis online

Engineering Mechanics

  1. JE Civil 2025 · 2 November · Q48 · Mechanics & Structural Analysis · Engineering Mechanics

    A frame having (M) number of member and joints (J) is said to be perfect frame if it follows the equation as given below

    1. J = 2M − 3
    2. M = 2J − 3
    3. M = 3J − 2
    4. J = M + 3
    Show answer

    Answer: (2) M = 2J − 3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  2. JE Civil 2023 · 19 November · Q4 · Mechanics & Structural Analysis · Engineering Mechanics

    A stone is thrown vertically upwards with a vertical velocity of 98 m/sec. It returns to the ground in

    1. 5 sec
    2. 10 sec
    3. 20 sec
    4. 98 sec
    Show answer

    Answer: (3) 20 sec

    Time to reach the top: t = u/g = 98/9.8 = 10 s; it takes the same time to fall back. Total time of flight = 2u/g = 2 × 98/9.8 = 20 s.

  3. JE Civil 2023 · 19 November · Q5 · Mechanics & Structural Analysis · Engineering Mechanics

    Two horizontal force F1=80 N and F2 = 70 N acting on a 20 kg block kept on rough horizontal surface, having coefficient of friction = 0.4, shown in following figure. The magnitude of the net acceleration of the block

    Figure for question 5
    1. 0 m / sec²
    2. 10 m / sec²
    3. 20 m / sec²
    4. 48 m / sec²
    Show answer

    Answer: (1) 0 m / sec²

    The forces oppose each other, so the net applied force is 80 − 70 = 10 N. Limiting friction = μmg = 0.4 × 20 × 9.81 ≈ 78.5 N, which is far more than 10 N, so static friction (10 N) balances the push and the block stays at rest: a = 0.

  4. JE Civil 2023 · 19 November · Q6 · Mechanics & Structural Analysis · Engineering Mechanics

    Which of the following option is true about the moment of inertia of a section? i. The unit of moment of an area does not depends upon the units of its area. ii. The moment of inertia of an area may be obtained by the methods of integration. iii. The Routh's rule is used in finding out the moment of a body which is unsymmetrical about three mutually perpendicular axes. The true option is

    1. Only (i)
    2. Only (ii)
    3. Only (iii)
    4. None of the above is correct
    Show answer

    Answer: (2) Only (ii)

    (ii) is true: I = ∫y² dA. (i) is false: moment of inertia of an area has units of length⁴ (mm⁴, m⁴), so it depends on the units used. (iii) is false: Routh's rule applies to bodies that are symmetrical about three mutually perpendicular axes.

  5. JE Civil 2023 · 19 November · Q54 · Mechanics & Structural Analysis · Engineering Mechanics

    Match the following Forces with their examples and select the correct answer using the codes given below: Forces — Examples a. Collinear forces — 1. Forces on a rope in a tug of war b. Coplanar concurrent forces — 2. Forces on a rod resting against a wall c. Non-coplanar concurrent forces — 3. A tripod carrying a camera d. Non-coplanar parallel forces — 4. The weight of benches in a classroom

    1. a-1, b-2, c-3, d-4
    2. a-2, b-1, c-4, d-3
    3. a-1, b-3, c-4, d-2
    4. a-4, b-3, c-1, d-2
    Show answer

    Answer: (1) a-1, b-2, c-3, d-4

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  6. JE Civil 2023 · 19 November · Q55 · Mechanics & Structural Analysis · Engineering Mechanics

    In a lifting machine, an effort of 500 N is to be moved by a distance of 20 m to raise a load of 10,000 N by a distance of 0.8 m. Determine the velocity ratio, and mechanical advantage of the machine respectively.

    1. 25 and 20
    2. 15 and 20
    3. 25 and 15
    4. 10 and 15
    Show answer

    Answer: (1) 25 and 20

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  7. JE Civil 2023 · 19 November · Q93 · Mechanics & Structural Analysis · Engineering Mechanics

    "If a number of coplanar forces acting on a particle are in equilibrium, then the algebraic sum of their moments about any point is equal to the moment of their resultant force about the same point" is

    1. Lami's Theorem
    2. Varignon's Theorem
    3. Cauchy's Theorem
    4. Euler's Theorem
    Show answer

    Answer: (2) Varignon's Theorem

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  8. JE Civil 2023 · 19 November · Q96 · Mechanics & Structural Analysis · Engineering Mechanics

    Find the centroid of laminae shown in figure

    Figure for question 96
    1. (50 mm, 45 mm)
    2. (50 mm, 35 mm)
    3. (50 mm, 17 mm)
    4. (50 mm, 27 mm)
    Show answer

    Answer: (3) (50 mm, 17 mm)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

Strength of Materials

  1. JE Civil 2025 · 2 November · Q11 · Mechanics & Structural Analysis · Strength of Materials

    Robert Hooke discovered experimentally that within elastic limit

    1. Stress = strain
    2. Stress × strain = 1
    3. Stress / Strain = a constant
    4. None of the above
    Show answer

    Answer: (3) Stress / Strain = a constant

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  2. JE Civil 2025 · 2 November · Q12 · Mechanics & Structural Analysis · Strength of Materials

    A circular bar is subjected to an axial pull of 100 kN. If the maximum intensity of shear stress on any oblique plane is not to exceed 60 MN/m², determine the diameter of the bar.

    1. 21.6 mm
    2. 32.6 mm
    3. 45.6 mm
    4. 48.6 mm
    Show answer

    Answer: (2) 32.6 mm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  3. JE Civil 2025 · 2 November · Q13 · Mechanics & Structural Analysis · Strength of Materials

    In case of a circular section, the maximum shear stress is ______ percent more than the mean shear stress.

    1. 10
    2. 20
    3. 33.33
    4. 66.66
    Show answer

    Answer: (3) 33.33

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  4. JE Civil 2025 · 2 November · Q14 · Mechanics & Structural Analysis · Strength of Materials

    In a rectangular section, the stress will be of the same sign throughout the section if the load lies within the ______ of the section.

    1. Middle third
    2. Middle half
    3. Both (A) and (B)
    4. None of the above
    Show answer

    Answer: (1) Middle third

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  5. JE Civil 2025 · 2 November · Q15 · Mechanics & Structural Analysis · Strength of Materials

    A cantilever 1.5 m long carries a uniformly distributed load over the entire length. Find the deflection at the free end if the slope at the free end is 1.5°.

    1. 21.88 mm
    2. 29.45 mm
    3. 36.48 mm
    4. 41.54 mm
    Show answer

    Answer: (2) 29.45 mm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  6. JE Civil 2025 · 2 November · Q16 · Mechanics & Structural Analysis · Strength of Materials

    The slope and deflection at a section in a loaded beam can be found out by which of the following methods?

    1. Double integration method
    2. Moment area method
    3. Macaulay's method
    4. Any of the above
    Show answer

    Answer: (4) Any of the above

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  7. JE Civil 2025 · 2 November · Q17 · Mechanics & Structural Analysis · Strength of Materials

    The material that exhibits the same elastic properties in all directions at a point is said to be ______

    1. homogeneous
    2. orthotropic
    3. viscoelastic
    4. isotropic
    Show answer

    Answer: (4) isotropic

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  8. JE Civil 2025 · 2 November · Q18 · Mechanics & Structural Analysis · Strength of Materials

    If principal stresses in a two-dimensional case are −10 MPa and 20 MPa respectively, then maximum shear stress at the point is

    1. 10 MPa
    2. 15 MPa
    3. 20 MPa
    4. 30 MPa
    Show answer

    Answer: (2) 15 MPa

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  9. JE Civil 2025 · 2 November · Q20 · Mechanics & Structural Analysis · Strength of Materials

    The following statement are related to bending of beams I. The slope of the bending moment diagram is equal to the shear force II. The slope of the shear force diagram is equal to the load intensity III. The slope of the curvature is equal to the flexural rotation IV. The second derivative of the deflection is equal to the curvature The only FALSE statement is

    1. I
    2. II
    3. III
    4. IV
    Show answer

    Answer: (3) III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  10. JE Civil 2025 · 2 November · Q21 · Mechanics & Structural Analysis · Strength of Materials

    A circular solid shaft of span L = 5 m is fixed at one end and free at the other end. A twisting moment T = 100 kN-m is applied at the free end. The torsional rigidity GJ is 50000 kN-m²/rad. Following statements are made for this shaft: 1. The maximum rotation is 0.01 rad 2. The torsional strain energy is 1 kN-m With reference to the above statements, which of the following applies?

    1. Both statements are true
    2. Statement 1 is true but 2 is false
    3. Statement 2 is true but 1 is false
    4. Both statements are false
    Show answer

    Answer: (2) Statement 1 is true but 2 is false

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  11. JE Civil 2025 · 2 November · Q22 · Mechanics & Structural Analysis · Strength of Materials

    Consider the following statements: I. On a principal plane, only normal stress acts II. On a principal plane, both normal and shear stresses act III. On a principal plane, only shear stress acts IV. Isotropic state of stress is independent of frame of reference Which of these statements is/are correct?

    1. I and IV
    2. II only
    3. II and IV
    4. II and III
    Show answer

    Answer: (1) I and IV

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  12. JE Civil 2025 · 2 November · Q23 · Mechanics & Structural Analysis · Strength of Materials

    The "Plane section remain plane" assumption in bending theory implies

    1. Stress profile is linear
    2. Strain profile is linear
    3. Both profiles are linear
    4. Shear deformation is neglected
    Show answer

    Answer: (2) Strain profile is linear

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  13. JE Civil 2025 · 2 November · Q24 · Mechanics & Structural Analysis · Strength of Materials

    List-I shows different loads acting on a beam and List-II shows different bending moment distributions. Match the load with the corresponding bending moment diagram.

    Figure for question 24
    1. A - 4, B - 2, C - 1, D - 3
    2. A - 4, B - 3, C - 1, D - 2
    3. A - 2, B - 3, C - 4, D - 1
    4. None of the above
    Show answer

    Answer: (4) None of the above

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  14. JE Civil 2025 · 2 November · Q25 · Mechanics & Structural Analysis · Strength of Materials

    Four columns of the same material and having identical geometric properties are supported in different ways as shown below: It is required to arrange these four columns in the increasing order of their respective first buckling loads. The correct order is given by

    Figure for question 25
    1. I, II, III, IV
    2. III, IV, I, II
    3. II, I, IV, III
    4. I, II, IV, III
    Show answer

    Answer: (4) I, II, IV, III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  15. JE Civil 2025 · 2 November · Q49 · Mechanics & Structural Analysis · Strength of Materials

    Consider the following pairs, for a cantilever beam of length (l), loaded by point load (w) and flexural rigidity (EI). i. Maximum Bending Moment — 1. wl ii. Strain Energy — 2. wl²/2EI iii. Maximum slop — 3. wl³/3EI iv. Maximum deflection — 4. w²l³/6EI Which of the pair given below is correctly matched?

    1. (i)-(1), (ii)-(4), (iii)-(3), (iv)-(2)
    2. (i)-(1), (ii)-(4), (iii)-(2), (iv)-(3)
    3. (i)-(4), (ii)-(2), (iii)-(1), (iv)-(3)
    4. (i)-(4), (ii)-(3), (iii)-(1), (iv)-(2)
    Show answer

    Answer: (2) (i)-(1), (ii)-(4), (iii)-(2), (iv)-(3)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  16. JE Civil 2025 · 2 November · Q57 · Mechanics & Structural Analysis · Strength of Materials

    Distribution of shear stress intensity over a rectangular section of a loaded beam follows diagrammatically

    1. A circular curve
    2. A straight line
    3. A parabolic curve
    4. An elliptical curve
    Show answer

    Answer: (3) A parabolic curve

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  17. JE Civil 2023 · 19 November · Q7 · Mechanics & Structural Analysis · Strength of Materials

    The state of pure shear stress is produced by

    1. Tension in one direction and equal compression in perpendicular direction
    2. Equal tension in two directions at right angles
    3. Equal compression in two directions at right angles
    4. Same magnitude of compressive stress in all three direction
    Show answer

    Answer: (1) Tension in one direction and equal compression in perpendicular direction

    With principal stresses σ1 = +σ and σ2 = −σ, the normal stress on planes at 45° is (σ1 + σ2)/2 = 0 and the shear stress there is (σ1 − σ2)/2 = σ: a state of pure shear. Equal tensions or equal compressions in two directions (B, C) give zero in-plane shear on every plane, and equal all-round compression (D) gives no shear at all.

  18. JE Civil 2023 · 19 November · Q8 · Mechanics & Structural Analysis · Strength of Materials

    At the time of designing a 40 m length chimney with one end is fixed, effective length is considered as

    1. 20 m
    2. 40 m
    3. 80 m
    4. 120 m
    Show answer

    Answer: (3) 80 m

    A chimney behaves as a vertical cantilever, fixed at the base and free at the top. For one end fixed and the other free, effective length = 2L = 2 × 40 = 80 m.

  19. JE Civil 2023 · 19 November · Q56 · Mechanics & Structural Analysis · Strength of Materials

    A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at other end in a length of 600 mm. If the bar is subjected to a load of 80 KN, find its extension. Take E=2×105 MPa.

    1. 0.486
    2. 0.386
    3. 0.225
    4. 0.724
    Show answer

    Answer: (1) 0.486

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  20. JE Civil 2023 · 19 November · Q70 · Mechanics & Structural Analysis · Strength of Materials

    Slenderness ratio of a 5 m long column hinged at both ends and having a circular cross-section with diameter 160 mm is

    1. 31.25.
    2. 62.5.
    3. 100.
    4. 125.
    Show answer

    Answer: (4) 125.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  21. JE Civil 2023 · 19 November · Q71 · Mechanics & Structural Analysis · Strength of Materials

    Match List I with List II and select the correct answer from the combinations given below: List - I — List - II a. Moment of inertia. — 1. Tensile stress. b. Elongation. — 2. Modulus of rupture. c. Neutral axis. — 3. Zero shear stress. d. Top fibre. — 4. Zero longitudinal stress. The correct combination is:

    1. a-2 b-1 c-3 d-4.
    2. a-1 b-2 c-4 d-3.
    3. a-3 b-4 c-1 d-2.
    4. a-2 b-1 c-4 d-3.
    Show answer

    Answer: (4) a-2 b-1 c-4 d-3.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  22. JE Civil 2023 · 19 November · Q72 · Mechanics & Structural Analysis · Strength of Materials

    Consider the following statements: A simply supported beam is subjected to a couple somewhere in the span. It would produce (i) A rectangular SF diagram. (ii) Parabolic BM diagrams. (iii) Both +ve and -ve BMs which are maximum at the point of application of the couple. Of these statements

    1. (i), (ii), and (iii) are correct.
    2. (i) and (ii) are correct.
    3. (ii) and (iii) are correct.
    4. (i) and (iii) are correct.
    Show answer

    Answer: (4) (i) and (iii) are correct.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  23. JE Civil 2023 · 19 November · Q95 · Mechanics & Structural Analysis · Strength of Materials

    A simply supported beam AB has the bending moment diagram as shown in the following figure. The beam is possibly under the action of following loads:

    Figure for question 95
    1. Couples of M at C and 2M at D
    2. Couples of 2M at C and M at D
    3. Concentrated loads of M/L at C and 2M/L at D
    4. Concentrated loads of M/L at C and couple of 2M at D
    Show answer

    Answer: (1) Couples of M at C and 2M at D

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  24. JE Civil 2023 · 19 November · Q99 · Mechanics & Structural Analysis · Strength of Materials

    Statement I: Fibres in the neutral layer of a beam under simple bending is always stressed. Statement II: The resultant pull or thrust on a transverse section of the beam under pure bending is zero. Out of following, which option is correct?

    1. Statement I and Statement II are True
    2. Statement I and Statement II are False
    3. Statement I is False and Statement II is True
    4. Statement I is True and Statement II is False
    Show answer

    Answer: (3) Statement I is False and Statement II is True

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

Structural Analysis

  1. JE Civil 2025 · 2 November · Q19 · Mechanics & Structural Analysis · Structural Analysis

    All the members of the planar truss (see figure), have the same properties in terms of area of cross-section (A) and modulus of elasticity (E), For the loads shown on the truss, the statements that correctly represents the nature of forces in the members of the truss is:

    Figure for question 19
    1. There are 3 members in tension, and 2 members in compression
    2. There are 2 members in tension, and 2 members in compression, 1 zero-force member
    3. There are 2 members in tension, 1 member in compression, and 2 zero-force members
    4. There are 2 members in tension, and 3 zero-force members
    Show answer

    Answer: (4) There are 2 members in tension, and 3 zero-force members

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  2. JE Civil 2025 · 2 November · Q51 · Mechanics & Structural Analysis · Structural Analysis

    Which of the following Indian Standard (IS) code used for wind load analysis for designing building structure

    1. IS 456
    2. IS 800
    3. IS 875
    4. IS 1893
    Show answer

    Answer: (3) IS 875

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  3. JE Civil 2023 · 19 November · Q53 · Mechanics & Structural Analysis · Structural Analysis

    The simplest space frame or truss consists of six members joined to form

    1. Tetrahedron
    2. Hexahedron
    3. Dodecahedron
    4. Octahedron
    Show answer

    Answer: (1) Tetrahedron

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  4. JE Civil 2023 · 19 November · Q69 · Mechanics & Structural Analysis · Structural Analysis

    In the cantilever method of lateral load analysis, which of the following assumptions are made? (i) The axial force in the beam is zero. (ii) The intensity of axial stress in each column of a storey is proportional to the horizontal distance of that column from the centre of gravity of all columns of the storey under consideration. (iii) The total horizontal shear on each storey is divided between the columns of that storey so that each interior column catties twice as much shear as each exterior column. The correct answer is

    1. (i) and (ii).
    2. (i) and (iii).
    3. Only (ii).
    4. Only (iii).
    Show answer

    Answer: (3) Only (ii).

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  5. JE Civil 2023 · 19 November · Q73 · Mechanics & Structural Analysis · Structural Analysis

    In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero. (ii) Shear force at mid span is maximum. (iii) Torsion at mid span is zero. (iv) Torsion at mid span is maximum. The correct answer is

    1. (i) and (iii).
    2. (i) and (iv).
    3. (ii) and (iii).
    4. (ii) and (iv).
    Show answer

    Answer: (1) (i) and (iii).

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  6. JE Civil 2023 · 19 November · Q94 · Mechanics & Structural Analysis · Structural Analysis

    If the member is denoted by m and joints by j, the condition for a frame to be redundant is given by:

    1. m < 2j+3
    2. m < 2j - 3
    3. m > 2j - 3
    4. m > 2j + 3
    Show answer

    Answer: (3) m > 2j - 3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.