Learn with Anil · JKSSB JE Civil PYQsPractise online →Subscribe ₹149

JKSSB JE Civil RCC & Steel Design previous year questions with answers

Every RCC & Steel Design question asked in the JKSSB JE Civil papers on this site, grouped by topic. Answers come from JKSSB's key; each has a short explanation (free here for a sample, all of them in the practice app).

Practise RCC & Steel Design online

RCC Design

  1. JE Civil 2025 · 2 November · Q47 · RCC & Steel Design · RCC Design

    As per limit state design method the ultimate strain in the outermost compression fiber of concrete in bending is taken as

    1. 0.0020
    2. 0.0120
    3. 0.0035
    4. 0.0520
    Show answer

    Answer: (3) 0.0035

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  2. JE Civil 2025 · 2 November · Q52 · RCC & Steel Design · RCC Design

    In a cantilever RCC beam design, tensile reinforcement is provided

    1. On the top of the beam
    2. On the bottom of the beam
    3. In the middle of the beam
    4. On the top and bottom of the beam
    Show answer

    Answer: (1) On the top of the beam

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  3. JE Civil 2025 · 2 November · Q56 · RCC & Steel Design · RCC Design

    Side face reinforcement is required when the depth of the web of a beam is

    1. Greater than 750 mm
    2. Greater than 900 mm
    3. Greater than 950 mm
    4. Greater than 1000 mm
    Show answer

    Answer: (1) Greater than 750 mm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  4. JE Civil 2025 · 2 November · Q60 · RCC & Steel Design · RCC Design

    The main reinforcement of a RC slab consists of 6 mm bars at 10 cm spacing if it is desired to replace 6 mm bars by 12 mm bars, then spacing of 12 mm bars should be

    1. 10 cm
    2. 40 cm
    3. 60 cm
    4. 120 cm
    Show answer

    Answer: (2) 40 cm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  5. JE Civil 2023 · 19 November · Q11 · RCC & Steel Design · RCC Design

    If the depth of neutral axis for singly reinforced rectangular section is represented by "Kd" in working stress design, then the value of "K" for balance section where 'D' is the effective depth, σst permissible stress in steel in tension and σcbc is permissible stress in steel in bending compression.

    1. Depends on σst only
    2. Depends on σcbc only
    3. Depends on Both σst and σcbc
    4. Is independent of Both σst and σcbc
    Show answer

    Answer: (1) Depends on σst only

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  6. JE Civil 2023 · 19 November · Q40 · RCC & Steel Design · RCC Design

    A RC beam has cross section 300mm×600mm and is subjected to the following design forces Bending moment =115KN-m Shear force = 95KN-m Torsional moment = 45KN-m Determine the equivalent bending moment for which section is to be designed.

    1. 194.41 KN-m
    2. 205.6 KN-m
    3. 150.63 KN-m
    4. 146.56 KN-m
    Show answer

    Answer: (1) 194.41 KN-m

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  7. JE Civil 2023 · 19 November · Q41 · RCC & Steel Design · RCC Design

    According to I.S.: 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is

    1. Half of the width of the slab
    2. Two-third of the width of the slab
    3. Three-fourth of the width of the slab
    4. Four-fifth of the width of the slab
    Show answer

    Answer: (3) Three-fourth of the width of the slab

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  8. JE Civil 2023 · 19 November · Q75 · RCC & Steel Design · RCC Design

    If a simply supported concrete beam, prestressed with a force of 2500 kN, is designed by load balancing concept for an effective span of 10m and to carry a total load of 40 kN/m, the central dip of the cable profile should be

    1. 100 mm.
    2. 200 mm.
    3. 300 mm.
    4. 400 mm.
    Show answer

    Answer: (2) 200 mm.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.