JKSSB JE Civil 2023 question paper with answers
JKSSB Junior Engineer (Civil) OMR Exam 2023 (19 November) Question Paper. JKSSB JE (Civil) OMR test: 120 Civil Engineering questions in 120 minutes, 1 mark each, ¼ mark cut for each wrong answer, in English. Held on 19 November 2023 (JKSSB Advt. No. 06 of 2022, Series A). All four options with the answer from JKSSB's final answer key (7 December 2023), plus a short explanation for every question (the first 10 here, all of them in the app). Each question is shown in English and Hindi, as printed in the booklet.
यूपीएससी सीएपीएफ (असिस्टेंट कमांडेंट) 2023 प्रश्न पत्र, उत्तर कुंजी सहित
Attempt this paper · 120 min timerMake a topic-wise quizThe correct answer to every question is free on this page, and so are the explanations of the first 10. For all 115 explanations, practise the paper in the app with the ₹149 All-in-One Pass, one payment for every exam on the site.
Subjects in this paper
All 115 questions
Theory of probability can be applied to
- Cumulative errors only
- Accidental errors only
- Both accidental and cumulative errors
- None of the above is correct
Show answer
Answer: (2) Accidental errors only
Accidental (random) errors are small, equally likely to be positive or negative and follow the normal law of probability, so probable error and least-squares adjustment apply to them. Cumulative (systematic) errors follow a definite law and are removed by calculated corrections, not by probability.
The principle of "working from whole to part" is used in surveying because
- Plotting and mapping becomes easy
- Survey work can be completed quickly
- Accumulation of errors is prevented
- Lower manpower requirement
Show answer
Answer: (3) Accumulation of errors is prevented
A framework of main control points is first fixed with high precision and the details are then filled in by less precise methods. Errors in the minor work stay localised within the framework instead of accumulating and magnifying, as they would when working from part to whole.
The relation between the radius (R) and degree (D) of a curve is
- R = D/1719
- R = 1719/D
- R/D = 1719
- D/R = 1719
Show answer
Answer: (2) R = 1719/D
Degree of curve D is the angle subtended at the centre by a 30 m arc. So 30 = R × D × π/180, giving R = 5400/(πD) = 1718.9/D ≈ 1719/D (R in metres, D in degrees). A sharper curve (larger D) has a smaller radius.
A stone is thrown vertically upwards with a vertical velocity of 98 m/sec. It returns to the ground in
- 5 sec
- 10 sec
- 20 sec
- 98 sec
Show answer
Answer: (3) 20 sec
Time to reach the top: t = u/g = 98/9.8 = 10 s; it takes the same time to fall back. Total time of flight = 2u/g = 2 × 98/9.8 = 20 s.
Two horizontal force F1=80 N and F2 = 70 N acting on a 20 kg block kept on rough horizontal surface, having coefficient of friction = 0.4, shown in following figure. The magnitude of the net acceleration of the block
- 0 m / sec²
- 10 m / sec²
- 20 m / sec²
- 48 m / sec²
Show answer
Answer: (1) 0 m / sec²
The forces oppose each other, so the net applied force is 80 − 70 = 10 N. Limiting friction = μmg = 0.4 × 20 × 9.81 ≈ 78.5 N, which is far more than 10 N, so static friction (10 N) balances the push and the block stays at rest: a = 0.
Which of the following option is true about the moment of inertia of a section? i. The unit of moment of an area does not depends upon the units of its area. ii. The moment of inertia of an area may be obtained by the methods of integration. iii. The Routh's rule is used in finding out the moment of a body which is unsymmetrical about three mutually perpendicular axes. The true option is
- Only (i)
- Only (ii)
- Only (iii)
- None of the above is correct
Show answer
Answer: (2) Only (ii)
(ii) is true: I = ∫y² dA. (i) is false: moment of inertia of an area has units of length⁴ (mm⁴, m⁴), so it depends on the units used. (iii) is false: Routh's rule applies to bodies that are symmetrical about three mutually perpendicular axes.
The state of pure shear stress is produced by
- Tension in one direction and equal compression in perpendicular direction
- Equal tension in two directions at right angles
- Equal compression in two directions at right angles
- Same magnitude of compressive stress in all three direction
Show answer
Answer: (1) Tension in one direction and equal compression in perpendicular direction
With principal stresses σ1 = +σ and σ2 = −σ, the normal stress on planes at 45° is (σ1 + σ2)/2 = 0 and the shear stress there is (σ1 − σ2)/2 = σ: a state of pure shear. Equal tensions or equal compressions in two directions (B, C) give zero in-plane shear on every plane, and equal all-round compression (D) gives no shear at all.
At the time of designing a 40 m length chimney with one end is fixed, effective length is considered as
- 20 m
- 40 m
- 80 m
- 120 m
Show answer
Answer: (3) 80 m
A chimney behaves as a vertical cantilever, fixed at the base and free at the top. For one end fixed and the other free, effective length = 2L = 2 × 40 = 80 m.
Presence of 0.20% sugar by weight of cement in the mixing water is likely to
- Retard the setting of cement
- Reduce the early strength of cement
- Accelerate the setting of cement
- Decrease the work ability
Show answer
Answer: (1) Retard the setting of cement
Sugar is a powerful retarder. About 0.05% by mass of cement delays setting by roughly 4 hours, and at about 0.2% hydration is retarded so much that the final set may not occur for 72 hours or more (Neville). So 0.20% sugar in the mixing water retards the setting of cement.
If water-cement ratio is 0.6 then, water content per standard bag of cement is
- 10 kg
- 20 kg
- 30 kg
- 50 kg
Show answer
Answer: (3) 30 kg
A standard bag of cement weighs 50 kg. Water = w/c ratio × mass of cement = 0.6 × 50 = 30 kg (about 30 litres).
If the depth of neutral axis for singly reinforced rectangular section is represented by "Kd" in working stress design, then the value of "K" for balance section where 'D' is the effective depth, σst permissible stress in steel in tension and σcbc is permissible stress in steel in bending compression.
- Depends on σst only
- Depends on σcbc only
- Depends on Both σst and σcbc
- Is independent of Both σst and σcbc
Show answer
Answer: (1) Depends on σst only
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The soil has a bulk density of 44 kN/m³ and water content 10%. The dry density of soil is
- 4.4 kN/m³
- 10 kN/m³
- 20 kN/m³
- 40 kN/m³
Show answer
Answer: (4) 40 kN/m³
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Considering i. The structural resistance to displacement of the soil ii. Frictional resistance between the individual soil particles iii. Cohesion between the surface of the soil particles. The Shear strength of a soil basically made up of these statements
- Only (i) and (ii)
- Only (ii) and (iii)
- Only (i), and (iii)
- (i), (ii) and (iii)
Show answer
Answer: (4) (i), (ii) and (iii)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Find the height of water column equivalent to a pressure of 3×10³ gm/cm². Specific weight of liquid is 1 gm/ cm³
- 3 meter
- 30 cm
- 30 meter
- 3000 meter
Show answer
Answer: (3) 30 meter
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match the list-1 with list-2 and select the correct answer using the codes given below, List -1 (Property of fluid) — List -2 (Description) a. Viscosity — 1. Property which explains the spherical shape of the drop of liquid b. Surface tension — 2. Property which explains the rise of liquid in tube c. Compressibility — 3. Property which explains the resistance of a fluid to flow d. Capillarity — 4. Property which explains the measure of the relative volume change of a fluid in response to the pressure change Correct codes:
- a-1, b-2, c-4, d-3
- a-3, b-1, c-4, d-2
- a-4, b-2, c-3, d-1
- a-2, b-1, c-4, d-3
Show answer
Answer: (2) a-3, b-1, c-4, d-2
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
During designing water supply line of a housing complex, two distribution pipes of different diameter 2 cm, and 6 cm respectively are connected with the main supply pipe line. The velocity of flow of water in the pipe of 2 cm diameter is
- 4 times that in the 6 cm diameter pipe
- 6 times that in the 6 cm diameter pipe
- 9 times that in the 6 cm diameter pipe
- 12 times that in the 6 cm diameter pipe
Show answer
Answer: (3) 9 times that in the 6 cm diameter pipe
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Piezometric head is the sum of
- Velocity head and pressure head
- Pressure head and datum head
- Datum head and velocity head
- Velocity head, pressure head and datum head
Show answer
Answer: (2) Pressure head and datum head
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Considering, i. Controlling flood ii. Generating hydropower iii. Preventing loss of water in percolation from fields iv. Sewage disposal. A reservoir is used for Correct answer is
- (i) and (ii)
- (i) and (iii)
- Only (iii)
- (iii) and (iv)
Show answer
Answer: (1) (i) and (ii)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match the list-1 with list-2 and select the correct answer using the codes given below, List -1 (Name of the instrument) — List -2 (Purpose) a. Current meter — 1. Control silt entry into the canal b. Echo sounder — 2. Control water levels and flow rates in canal c. Head regulator — 3. Depth of flow d. Sluice gate — 4. Velocity of flow of water Correct codes:
- a-1, b-2, c-4, d-3
- a-1, b-3, c-2, d-4
- a-4, b-3, c-1, d-2
- a-2, b-4, c-1, d-3
Show answer
Answer: (3) a-4, b-3, c-1, d-2
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match the list-1 with list-2 and select the correct answer using the codes given below, List -1 (Name of the valve) — List -2 (Purpose of the valve) a. Reflux valve — 1. Drain out the west water from dead end b. Sluice valve — 2. Relieving water hammer pressure c. Pressure relief valve — 3. Control the flow in the distribution system at corner and pipe junction d. Scour valve — 4. Allow the flow only in one direction Correct codes:
- a-1, b-2, c-4, d-3
- a-4, b-3, c-2, d-1
- a-4, b-2, c-3, d-1
- a-1, b-2, c-3, d-4
Show answer
Answer: (2) a-4, b-3, c-2, d-1
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Considering i. Screening ii. Sedimentation iii. Disinfection iv. Filtration. The correct sequence of treatments which are generally given to treat raw water supplies are
- (i) (ii) (iii) (iv)
- (i) (ii) (iv) (iii)
- (i) (iii) (iv) (ii)
- (iv) (iii) (ii) (i)
Show answer
Answer: (2) (i) (ii) (iv) (iii)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The standard loads corresponding to 2.5 mm and 5.0 mm deformation in California Bearing Ratio (CBR) Test are.
- 1350 N and 2055 N,
- 2055 N and 1350 N,
- 1350 kg and 2055 kg,
- 2055 kg and 1350 kg.
Show answer
Answer: (3) 1350 kg and 2055 kg,
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following devices is used to measure speed of a moving vehicle?
- Weigh bridge
- LIDAR gun
- Noise meter
- Loop detector
Show answer
Answer: (2) LIDAR gun
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Creep is a phenomenon of
- Longitudinal movement of rails in a track
- Lateral movement of rails in a track
- Difference of level between sleeper and rail
- Transverse movement of rails in a track
Show answer
Answer: (1) Longitudinal movement of rails in a track
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Consider the following surveys i. Reconnaissance survey ii. Preliminary survey iii. Traffic survey iv. Location survey The correct sequence of surveys conducted to finalized the railway alignment is
- (i) (iii) (ii) (iv)
- (i) (iii) (iv) (ii)
- (iii) (i) (iv) (ii)
- (iii) (i) (ii) (iv)
Show answer
Answer: (4) (iii) (i) (ii) (iv)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
With reference to the following network which statement is incorrect?
- Events 3 and 4 occur after event 2
- Event 7 can occur after event 4
- Event 7 preceded event 6
- Event 5 follows event 3
Show answer
Answer: (2) Event 7 can occur after event 4
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Difference between cost of property and accumulated depreciation cost is known as
- Market value
- Salvage value
- Book value
- Capital value
Show answer
Answer: (3) Book value
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Statement 1: Security deposit is an amount of money which is nonrefundable, even after the maintenance period is over. Statement 2: Retention money always forfeited by the department even after the finalization of maintenance or adjustment of the claim is over. The correct combination is
- Both statement (1) and statement (2) are individually true and statement (1) is correct explanation of statement (2)
- Statement (1) is true but statement (2) is false
- Statement (1) is false but statement (2) is true
- Both the statement (1) and Statement (2) are individually false
Show answer
Answer: (4) Both the statement (1) and Statement (2) are individually false
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match the list-1 with list-2 and select the correct answer using the codes given below, List -1 (Description) — List -2 (Purpose details or functions) a. Estimation — 1. Setting objectives and determining a course of action for achieving the project objectives. b. Planning — 2. The science of calculating the different load requirements, so that proposed structure can easily withstand worst-case scenarios for a particular duration. c. Quality control — 3. To ascertain the probable cost of a proposed project. d. Designing — 4. Testing units and determining whether the materials are within the specifications for the final product . Correct codes:
- a-1, b-2, c-4, d-3
- a-3, b-1, c-4, d-2
- a-4, b-2, c-3, d-1
- a-1, b-2, c-3, d-4
Show answer
Answer: (2) a-3, b-1, c-4, d-2
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The distribution system of water supplies is designed in the basis of ______
- Peak hourly demand
- Coincident draft
- Average daily demand
- Greater of (A) or (B)
Show answer
Answer: (4) Greater of (A) or (B)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Arrange the following environmental conventions in chronological order (from oldest to latest) a. Stockholm Convention b. Montreal Protocol c. Kyoto Protocol d. Basel Convention
- b> d> a> c
- a> c> b> d
- b> d> c> a
- c> a> d> b
Show answer
Answer: (3) b> d> c> a
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
What is the name of the water coming out of the kitchen, bathroom, and wash basin?
- Garbage
- Sullage
- Sewage
- Discharge
Show answer
Answer: (2) Sullage
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
If duty is 1428 hectares/cumec and base period is 120 days for an irrigated crop, then the delta in meters is given by
- 1.381
- 0.017
- 0.726
- 102.805
Show answer
Answer: (3) 0.726
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Khosla’s theory of independent variables is used in the design of a. Weirs and barrages b. Cross regulators and head regulators c. Modules
- a only
- c only
- Both a and b
- a, b and c
Show answer
Answer: (4) a, b and c
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Direction: The item consists of two statements, one labelled as the ‘Statement (I) and the other as ‘Statement (II)’. You are to examine these two statements carefully and select the answers to these items using the codes given below: Statement (I) : Cross drainage structure, aqueduct is constructed to negotiate an aligned channel over, below or at the same level of a stream. Statement (II) : Aqucduct is constructed, when full supply level (FSL) of canal is much higher than high flood level (HFL) of a stream
- Both Statement (I) and Statement (II) are individually true and Statement (II) is the correct explanation of Statement (I)
- Both Statement (I) and Statement (II) are individually true but Statement (II) is not the correct explanation of Statement (I)
- Statement (I) is true but Statement (II) is false
- Statement (I) is false but Statement (II) is true
Show answer
Answer: (4) Statement (I) is false but Statement (II) is true
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The switch angle depends on i. Heel divergence ii. Length of tongue rail iii. Flange-way clearance iv. Throw of switch The correct answer is
- (i) and (ii)
- (ii) and (iii)
- (iii) and (iv)
- (i) and (iv)
Show answer
Answer: (1) (i) and (ii)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Calculate the number of sleepers required for 1 km railway track , it sleeper density is (n+4) for broad gauge and the length of one rail for a broad gauge is 13 m.
- 437
- 678
- 1308
- 17000
Show answer
Answer: (3) 1308
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Consider the following pairs. List - I — List - II i. Broad gauge — 1676 ii. Meter gauge — 762 iii. Narrow gauge — 1000 Which of the pairs given above is/are correctly matched?
- i
- ii
- iii
- None of the above
Show answer
Answer: (1) i
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A RC beam has cross section 300mm×600mm and is subjected to the following design forces Bending moment =115KN-m Shear force = 95KN-m Torsional moment = 45KN-m Determine the equivalent bending moment for which section is to be designed.
- 194.41 KN-m
- 205.6 KN-m
- 150.63 KN-m
- 146.56 KN-m
Show answer
Answer: (1) 194.41 KN-m
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
According to I.S.: 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is
- Half of the width of the slab
- Two-third of the width of the slab
- Three-fourth of the width of the slab
- Four-fifth of the width of the slab
Show answer
Answer: (3) Three-fourth of the width of the slab
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Consider the following pairs. Admixtures — Chemicals a. Water reducing admixtures — Calcium chloride b. Air-entraining agent — Neutralized vinsol resin c. Super plasticizer — Sulphonated melanin d. Accelerator — Lignosulphonate Which of the pairs given above is/are correctly matched?
- b and c
- c and d
- a and d
- a and c
Show answer
Answer: (1) b and c
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Consider the following strengths of concrete: i. Cube strength ii. Cylinder strength iii. Split-tensile strength iv. Modulus of rupture The correct sequence in increasing order of these strengths is
- (iii), (iv), (ii), (i)
- (iii), (iv), (i), (ii)
- (iv), (iii), (ii), (i)
- (iv), (iii), (i), (ii)
Show answer
Answer: (1) (iii), (iv), (ii), (i)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match list I with list II and select the correct answer using the codes given below the list List - I — List - II a. Topographical survey — 1. To obtain data for carrying out any of project b. Geodetic survey — 2. To show the boundaries of fields, building, etc. c. Engineering survey — 3. To furnish the data for size and shape of the earth. d. Cadastral survey — 4. To show natural features of the country such as rivers, hills, lakes, roads, bridges etc.
- a-1, b-2, c-3, d-4
- a-2, b-1, c-4, d-3
- a-1, b-3, c-4, d-2
- a-4, b-3, c-1, d-2
Show answer
Answer: (4) a-4, b-3, c-1, d-2
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
After fixing the plane table to the tripod, the main operations that are needed at each plane table station are a. Levelling b. Orientation c. Centering The correct sequence for this operation is
- a, b, c
- a, c, b
- c, a, b
- b, c, a
Show answer
Answer: (2) a, c, b
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following properties depend on effective stress?
- Shear strength
- Compressibility
- Permeability
- All of the above
Show answer
Answer: (4) All of the above
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The expected time (E) of a PERT activity in terms of optimistic time (O), pessimistic time (P) and most likely time (M) is given by.
- E=(O+2M+P)/3
- E=(O+4M+P)/3
- E=(O+2M+P)/6
- E=(O+4M+P)/6
Show answer
Answer: (4) E=(O+4M+P)/6
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match the list - I with List - II and select the correct answer using the codes given below the list. List - I — List - II a. Open tender — 1. The tender enquiry is sent only to one party. b. Limited tender — 2. Open for everyone and anyone can take part in the tendering process. c. Single tender — 3. Offer of tender is sent to limited parties and is not open for all.
- a-1, b-2, c-3
- a-2, b-3, c-1
- a-3, b-2, c-1
- a-3, b-1, c-2
Show answer
Answer: (2) a-2, b-3, c-1
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The simplest space frame or truss consists of six members joined to form
- Tetrahedron
- Hexahedron
- Dodecahedron
- Octahedron
Show answer
Answer: (1) Tetrahedron
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match the following Forces with their examples and select the correct answer using the codes given below: Forces — Examples a. Collinear forces — 1. Forces on a rope in a tug of war b. Coplanar concurrent forces — 2. Forces on a rod resting against a wall c. Non-coplanar concurrent forces — 3. A tripod carrying a camera d. Non-coplanar parallel forces — 4. The weight of benches in a classroom
- a-1, b-2, c-3, d-4
- a-2, b-1, c-4, d-3
- a-1, b-3, c-4, d-2
- a-4, b-3, c-1, d-2
Show answer
Answer: (1) a-1, b-2, c-3, d-4
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
In a lifting machine, an effort of 500 N is to be moved by a distance of 20 m to raise a load of 10,000 N by a distance of 0.8 m. Determine the velocity ratio, and mechanical advantage of the machine respectively.
- 25 and 20
- 15 and 20
- 25 and 15
- 10 and 15
Show answer
Answer: (1) 25 and 20
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at other end in a length of 600 mm. If the bar is subjected to a load of 80 KN, find its extension. Take E=2×105 MPa.
- 0.486
- 0.386
- 0.225
- 0.724
Show answer
Answer: (1) 0.486
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The term alternate depth is used in open channel flow to denote the depths ______
- Having the same kinetic energy for a given discharge
- Having the same specific force for a given discharge
- Having the same specific energy for a given discharge
- Having the same total energy for a given discharge
Show answer
Answer: (3) Having the same specific energy for a given discharge
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A triangular open channel has a vertex angle of 90 degrees and carries flow at a critical depth of 0.30m. The discharge in the channel is
- 0.15 m³/s
- 0.2 m³/s
- 0.08 m³/s
- 0.11 m³/s
Show answer
Answer: (4) 0.11 m³/s
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A rectangular channel has a width of 2.0 m and carries a discharge of 4.8 m³/s with a depth of 1.60 m. At a certain section, a small, smooth hump with a flat top and of height 0.10 m is proposed to be built. Calculate the critical depth of flow. Neglect the energy loss.
- 1.824 m
- 1.256 m
- 2.230 m
- 0.876 m
Show answer
Answer: (4) 0.876 m
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
For steady incompressible flow through a closed conduit of uniform cross-section, the direction of the flow will always be
- From higher to lower elevation
- From higher to lower pressure
- From higher to lower velocity
- From higher to lower piezometric head
Show answer
Answer: (4) From higher to lower piezometric head
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
What were the main recommendations of Jayakar Committee: a. Central Road Fund was founded in 1929. b. Indian Road Congress was established in 1930. c. Central Road Research Institute started in 1950. d. More stress was given on long term planning programme for a period of 20 years. Which of the following statements is/are correct?
- a and d
- a, c and d
- b and c
- b, c, and d
Show answer
Answer: (1) a and d
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Choose the correct relation between gradient and camber?
- Gradient = Camber ×0.5
- Gradient = Camber ×2
- Camber = Gradient ×1.5
- Camber = Gradient
Show answer
Answer: (2) Gradient = Camber ×2
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The unit of dynamic viscosity of a fluid is
- M²/s
- Ns/m²
- Pa s/m²
- Kg s²/m²
Show answer
Answer: (2) Ns/m²
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following statements is true? 1. CPM is activity - oriented network 2. PERT is activity oriented
- Only 1 is true
- Only 2 is true
- Both are false
- Both are true
Show answer
Answer: (1) Only 1 is true
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
An open cubical tank of 2m side is filled with water. If the tank is rotated with an acceleration such that half of the water spills out, then the acceleration is equal to
- g/3.
- g/2.
- 2g/3.
- g.
Show answer
Answer: (4) g.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match List I with List II and select the correct answer using the combination given below the lists: List - I (Physical quantity) — List - II (Dimensional formula) a. Specific gravity. — 1. [M⁰L²T⁻¹] b. Coefficient of viscosity. — 2. [M⁰L⁰T⁻⁰] c. Kinematic viscosity. — 3. [ML⁻¹T⁻¹] d. Stress. — 4. [ML⁻¹T⁻²] The correct combination is:
- a-2 b-3 c-4 d-1
- a-4 b-1 c-2 d-3
- a-1 b-4 c-3 d-2
- a-2 b-3 c-1 d-4
Show answer
Answer: (4) a-2 b-3 c-1 d-4
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A hydraulic model of a spillway is constructed with a scale 1:16. If the prototype discharge is 2048 cumec, then the corresponding discharge for which the model should be tested is
- 1 cumec.
- 2 cumec.
- 4 cumec.
- 8 cumec.
Show answer
Answer: (2) 2 cumec.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A level was set up at a point A and distance to the staff station B was 100 m. The net combined correction due to curvature and refraction as applied to the staff reading is
- 0.00673 m.
- 0.000673 m.
- - 0.000673 m.
- - 0.00673 m.
Show answer
Answer: (3) - 0.000673 m.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
In the cantilever method of lateral load analysis, which of the following assumptions are made? (i) The axial force in the beam is zero. (ii) The intensity of axial stress in each column of a storey is proportional to the horizontal distance of that column from the centre of gravity of all columns of the storey under consideration. (iii) The total horizontal shear on each storey is divided between the columns of that storey so that each interior column catties twice as much shear as each exterior column. The correct answer is
- (i) and (ii).
- (i) and (iii).
- Only (ii).
- Only (iii).
Show answer
Answer: (3) Only (ii).
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Slenderness ratio of a 5 m long column hinged at both ends and having a circular cross-section with diameter 160 mm is
- 31.25.
- 62.5.
- 100.
- 125.
Show answer
Answer: (4) 125.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match List I with List II and select the correct answer from the combinations given below: List - I — List - II a. Moment of inertia. — 1. Tensile stress. b. Elongation. — 2. Modulus of rupture. c. Neutral axis. — 3. Zero shear stress. d. Top fibre. — 4. Zero longitudinal stress. The correct combination is:
- a-2 b-1 c-3 d-4.
- a-1 b-2 c-4 d-3.
- a-3 b-4 c-1 d-2.
- a-2 b-1 c-4 d-3.
Show answer
Answer: (4) a-2 b-1 c-4 d-3.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Consider the following statements: A simply supported beam is subjected to a couple somewhere in the span. It would produce (i) A rectangular SF diagram. (ii) Parabolic BM diagrams. (iii) Both +ve and -ve BMs which are maximum at the point of application of the couple. Of these statements
- (i), (ii), and (iii) are correct.
- (i) and (ii) are correct.
- (ii) and (iii) are correct.
- (i) and (iii) are correct.
Show answer
Answer: (4) (i) and (iii) are correct.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero. (ii) Shear force at mid span is maximum. (iii) Torsion at mid span is zero. (iv) Torsion at mid span is maximum. The correct answer is
- (i) and (iii).
- (i) and (iv).
- (ii) and (iii).
- (ii) and (iv).
Show answer
Answer: (1) (i) and (iii).
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The diameter of needle used in Vicat's apparatus for the determination of initial setting time is prescribed as
- 0.5 mm.
- 1 mm.
- 5 mm.
- 10 mm.
Show answer
Answer: (2) 1 mm.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
If a simply supported concrete beam, prestressed with a force of 2500 kN, is designed by load balancing concept for an effective span of 10m and to carry a total load of 40 kN/m, the central dip of the cable profile should be
- 100 mm.
- 200 mm.
- 300 mm.
- 400 mm.
Show answer
Answer: (2) 200 mm.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Select the correct statement.
- Unit weight of dry soil is greater than unit weight of wet soil.
- For dry soils, dry unit weight is less than total unit weight.
- Unit weight of soil increases due to submergence in water
- Unit weight of soil decreases due to submergence in water.
Show answer
Answer: (4) Unit weight of soil decreases due to submergence in water.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
In a triaxial compression test when drainage is allowed during the first stage (i. e. application of cell pressure) only and not during the second stage (i. e. application of deviator stress at constant cell pressure), the test is known as
- Consolidated drained test.
- Consolidated undrained test.
- Unconsolidated drained test.
- Unconsolidated undrained test.
Show answer
Answer: (2) Consolidated undrained test.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
According to Dicken's formula for estimating floods, the peak discharge is proportional to: Where A is catchment area in square kilometres.
- A
- A^(1/2)
- A^(2/3)
- A^(3/4)
Show answer
Answer: (4) A^(3/4)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Muskingham method of flood routing is
- Reservoir routing method.
- Channel routing method.
- Hydraulic method of flood routing.
- None of the above.
Show answer
Answer: (2) Channel routing method.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following treatments reduce salinity of water? (i) Flocculation and sedimentation. (ii) Filtration. (iii) Reverse osmosis. (iv) Electrodialysis. Select the correct answer given below.
- (i) and (ii)
- (iii) and (iv)
- (ii) and (iii)
- (i) and (iv)
Show answer
Answer: (2) (iii) and (iv)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match List I with List II and select the correct answer from the combinations given below: List - I (Terms/Description) — List - II (Treatment operation/process) a. Sludge volume index — 1. Settling in primary sedimentation tank. b. Thickening of sludge — 2. Settling in secondary sedimentation tank. c. Scum removal — 3. Filtration in trickling filter. d. Recycling of effluent — 4. Activated sludge process. The correct combination is
- a-2 b-4 c-1 d-3.
- a-4 b-2 c-3 d-1.
- a-2 b-4 c-3 d-1.
- a-4 b-2 c-1 d-3.
Show answer
Answer: (4) a-4 b-2 c-1 d-3.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
If b is the wheel track of a vehicle and h is the height of centre of gravity above road surface, then to avoid overturning and lateral skidding on a horizontal curve, the centrifugal ratio should always be
- Less than b/2h and greater than coefficient of lateral friction.
- Less than b/2h and also less than coefficient of lateral friction.
- Greater than b/2h and less than coefficient of lateral friction.
- Greater than b/2h and also greater than coefficient of lateral friction.
Show answer
Answer: (2) Less than b/2h and also less than coefficient of lateral friction.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
In CBR test the value of CBR is calculated at
- 2.5 mm penetration only.
- 5.0 mm penetration only.
- 7.5 mm penetration only.
- Both 2.5 mm and 5.0 mm penetrations.
Show answer
Answer: (4) Both 2.5 mm and 5.0 mm penetrations.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
In a bituminous pavement, alligator cracking is mainly due to
- Inadequate wearing course.
- Inadequate thickness of sub-base course of pavement.
- Use of excessive bituminous material.
- Fatigue arising from repeated stress applications.
Show answer
Answer: (4) Fatigue arising from repeated stress applications.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Flangeway clearance is the distance
- Between the adjoining faces of the running rail and the check rail near the crossing.
- Between the gauge faces of the stock rail and the tongue rail.
- Through which the tongue rail moves laterally at the toe of the switch.
- None of the above.
Show answer
Answer: (1) Between the adjoining faces of the running rail and the check rail near the crossing.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match List I with List II and select the correct answer from the combinations given below List - I — List - II a. Wire claw. — 1. To clean the ballast. b. Jim crow. — 2. To pack the ballast under sleeper. c. Beater. — 3. To bend the rails. d. Mallet. — 4. To sound the sleeper for packing. The correct combination is:
- a-1 b-3 c-2 d-4.
- a-1 b-4 c-3 d-2.
- a-2 b-1 c-3 d-4.
- a-2 b-3 c-1 d-4.
Show answer
Answer: (1) a-1 b-3 c-2 d-4.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Wear of rails is maximum in
- Tangent track.
- Sharp curve.
- Tunnels.
- Coastal area.
Show answer
Answer: (2) Sharp curve.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following earth moving machines has the shortest cycle time?
- Drag line.
- Hoe.
- Clam shell.
- Dipper shovel.
Show answer
Answer: (4) Dipper shovel.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The sinking fund is
- The fund for rebuilding a structure when its economic life is over.
- Raised to meet maintenance costs.
- The total sum to be paid to municipal authorities by the tenants.
- A part of the money kept in reverse for providing additional structures and structural modification.
Show answer
Answer: (1) The fund for rebuilding a structure when its economic life is over.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The time estimates obtained from four contractors P, Q, R and S for executing a particular job are as under:
Contractor Optimistic time (tₒ) Most likely time (tₗ) Pessimistic time (tₚ) P 5 10 13 Q 6 9 12 R 5 10 14 S 4 10 13 Which one of the contractors is more certain about completing the work in time:
- Contractor P
- Contractor Q
- Contractor R
- Contractor S
Show answer
Answer: (2) Contractor Q
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
If three consecutive ordinates are taken at 2 m intervals from a traverse line and measured as 1.8 m, 2.5 m and 2.0 m, then the area between the traverse line, the first and last ordinates and the boundary, by trapezoidal rule, is
- 17.6 sq m
- 8.8 sq m
- 18.8 sq m
- 7.6 sq m
Show answer
Answer: (2) 8.8 sq m
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Number of links in a 30 m metric chain is.
- 150
- 180
- 100
- 200
Show answer
Answer: (1) 150
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
"If a number of coplanar forces acting on a particle are in equilibrium, then the algebraic sum of their moments about any point is equal to the moment of their resultant force about the same point" is
- Lami's Theorem
- Varignon's Theorem
- Cauchy's Theorem
- Euler's Theorem
Show answer
Answer: (2) Varignon's Theorem
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
If the member is denoted by m and joints by j, the condition for a frame to be redundant is given by:
- m < 2j+3
- m < 2j - 3
- m > 2j - 3
- m > 2j + 3
Show answer
Answer: (3) m > 2j - 3
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A simply supported beam AB has the bending moment diagram as shown in the following figure. The beam is possibly under the action of following loads:
- Couples of M at C and 2M at D
- Couples of 2M at C and M at D
- Concentrated loads of M/L at C and 2M/L at D
- Concentrated loads of M/L at C and couple of 2M at D
Show answer
Answer: (1) Couples of M at C and 2M at D
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Find the centroid of laminae shown in figure
- (50 mm, 45 mm)
- (50 mm, 35 mm)
- (50 mm, 17 mm)
- (50 mm, 27 mm)
Show answer
Answer: (3) (50 mm, 17 mm)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following statement is correct about Portland Pozzolana Cement (PPC)?
- The long term strength of PPC is less and it has reduced heat of hydration and permeability.
- The long term strength of PPC is more and it has enhanced heat of hydration and permeability.
- The long term strength of PPC is more and it has reduced heat of hydration and permeability.
- The long term strength of PPC is less and it has reduced heat of hydration and enhanced permeability
Show answer
Answer: (3) The long term strength of PPC is more and it has reduced heat of hydration and permeability.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A test is done to assess the quality of concrete by ultrasonic pulse velocity method as per IS: 13311 (Part 1)-1992. The Pulse Velocity by Cross Probing obtained is 4 km/sec. Then in which concrete quality grading is it belongs to?
- Poor
- Doubtful
- Excellent
- Good
Show answer
Answer: (4) Good
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Statement I: Fibres in the neutral layer of a beam under simple bending is always stressed. Statement II: The resultant pull or thrust on a transverse section of the beam under pure bending is zero. Out of following, which option is correct?
- Statement I and Statement II are True
- Statement I and Statement II are False
- Statement I is False and Statement II is True
- Statement I is True and Statement II is False
Show answer
Answer: (3) Statement I is False and Statement II is True
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
As the cube size increases, the strength of concrete
- Decreases
- Increases
- Remains constant
- Insufficient data
Show answer
Answer: (1) Decreases
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The rollers ideally suited for cohesive soils are
- Sheep foot roller
- Vibratory roller
- Smooth wheeled roller
- Pneumatic roller
Show answer
Answer: (1) Sheep foot roller
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The ratio of unconfined compressive strength of an undisturbed sample of soil to that of a remoulded sample, at the same water content is known as
- Activity
- Sensitivity
- Damping
- Plasticity
Show answer
Answer: (2) Sensitivity
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Wheat is to be grown in a field having field capacity equal to 30% and the permanent wilting point equal to 10%. Irrigation water is to be supplied when the moisture content of the soil falls to 20%. The root zone depth is 1 m, dry weight of soil is 14 kN/m³ and the specific weight of water is 10 kN/m³. The Net Irrigation Requirement (NIR) for the above cultivation is:
- 28 cm of water
- 19.6 cm of water
- 21 cm of water
- 14 cm of water
Show answer
Answer: (4) 14 cm of water
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Full Reservoir Level (FRL) is:
- The maximum elevation to which reservoir water surface will rise during normal operating conditions
- The maximum level to which reservoir water will rise during worst design flood
- The normal operating level in a reservoir
- Both (A) and (C)
Show answer
Answer: (1) The maximum elevation to which reservoir water surface will rise during normal operating conditions
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The line in a dam section in within a dam section below which there are positive hydrostatic pressure within the dam?
- Seepage line
- Phreatic line
- Saturation line
- All of these
Show answer
Answer: (4) All of these
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The total area which can be economically irrigated from an irrigation system without considering the limitation of the quantity of water available
- Gross Command Area
- Culturable Command Area
- Gross Cultivable Area
- Mean sea level
Show answer
Answer: (1) Gross Command Area
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following curves/line represents the total project cost versus time in the best way?
- Straight line
- S shaped curve
- U shaped curve
- Parabola
Show answer
Answer: (3) U shaped curve
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following refers to the annual periodic payments made for the repayment of the capital invested?
- Annuity
- Sinking fund
- Depreciation
- Solatium
Show answer
Answer: (1) Annuity
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Filling work in trenches shall be carried out in layers of thickness not exceeding ______.
- 100mm
- 200mm
- 500mm
- 750mm
Show answer
Answer: (2) 200mm
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
What is the number of standard modular bricks required to make 1m³ of masonry?
- 400
- 450
- 500
- 900
Show answer
Answer: (3) 500
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match the following, instrument with its purpose : 1. Manometer — a. To measure the pressure at a point in a fluid 2. Nozzle meter — b. To measure velocity of flow of fluid 3. Pitot tube — c. To measure the rate of flow of fluid 4. Hydrometer — d. To measure the density of certain fluid
- 1-c, 2-d, 3-a, 4-b
- 1-b, 2-d, 3-c, 4-a
- 1-a, 2-c, 3-b, 4-d
- 1-d, 2-b, 3-c, 4-a
Show answer
Answer: (3) 1-a, 2-c, 3-b, 4-d
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
When a plate is immersed in a liquid parallel to the flow, it will be subjected to a pressure ______ that if the same plate is immersed perpendicular to the flow.
- Less than
- More than
- Equal to
- None of these
Show answer
Answer: (1) Less than
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Consider full flow occurring through the circular water pipe system as shown in figure, Determine the velocity, V (in m/s) in the branch pipe 'R'.
- 6
- 8
- 4
- 2
Show answer
Answer: (2) 8
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Consider the following statements related to the coefficient of dynamic viscosity (μ) and temperature (T) and choose the incorrect option(s). a. For water, 'μ' decreases when 'T' increases b. For water, 'μ' increases when 'T' increases c. For Air, 'μ' increases when 'T' increases d. For Air, 'μ' decreases when 'T' increases
- a and d
- b and c
- b and d
- a and c
Show answer
Answer: (3) b and d
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
What is the maximum ruling gradient permitted in Indian Railways in plains?
- 1 in 500
- 1 in 150
- 1 in 100
- 1 in 50
Show answer
Answer: (2) 1 in 150
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
What is the crossing number adopted by Indian Railways for high speeds?
- 1 in 8 1/2
- 1 in 16
- 1 in 12
- 1 in 20
Show answer
Answer: (2) 1 in 16 / (4) 1 in 20
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
If 25 ml of an odorous water sample requires 175 ml of distilled water to produce 200 ml of odour free mixture, then what is the threshold odour number (TON)?
- 7
- 8
- 10
- 12.5
Show answer
Answer: (2) 8
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
What is the minimum residual chlorine desired after the chlorination process?
- 0.2 ppm
- 2 ppm
- 20 ppm
- 1 ppm
Show answer
Answer: (1) 0.2 ppm
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Among the following water supply distribution system, which one is referred to as Reticulation system?
- Grid Iron system
- Dead end system
- Radial system
- Ring system
Show answer
Answer: (1) Grid Iron system
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
What is the most common camber for earthen roads?
- 1 in 20
- 1 in 24
- 1 in 30
- 1 in 36
Show answer
Answer: (3) 1 in 30
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.