Learn with Anil · TGPSC HMWSSB Manager (Engineering) PYQsPractise online →Subscribe ₹149

TGPSC HMWSSB Manager 2015 Paper 2 ECE question paper with answers

TSPSC Manager (Engineering), HMWSSB, 2015: Paper 2 (Electronics & Communication Engineering). Paper 2: Electronics & Communication Engineering (networks, electronic devices and circuits, digital electronics, signals and systems, control systems, analog and digital communication, electromagnetics, transmission lines, microwaves and antennas), 150 questions, 300 marks, 150 minutes, in English only. Held on 1 November 2015 (Notification 13/2015, Series A). All four options with the answer from TSPSC's final key, plus a short explanation for every question (the first 10 here, all of them in the app).

టీజీపీఎస్సీ జలమండలి (HMWSSB) మేనేజర్ (ఇంజనీరింగ్) పేపర్-2 ఎలక్ట్రానిక్స్ & కమ్యూనికేషన్ ఇంజనీరింగ్ 2015 ప్రశ్నపత్రం సమాధానాలతో

Attempt this paper · 145 min timerMake a topic-wise quiz

The correct answer to every question is free on this page, and so are the explanations of the first 10. For all 145 explanations, practise the paper in the app with the ₹149 All-in-One Pass, one payment for every exam on the site.

Subjects in this paper

All 145 questions

  1. Q1 · Network Theory · AC Circuits & Resonance

    A capacitor C is connected across a coil with resistance R and inductance L. The effective [impedance] of the circuit at resonance is

    1. 1/(RLC)
    2. RC/L
    3. L/(RC)
    4. L/√(RC)
    Show answer

    Answer: (3) L/(RC)

    For a coil (R in series with L) in parallel with C, the admittance at resonance is purely real: Y = R/(R² + ω₀²L²), and the resonance condition gives R² + ω₀²L² = L/C. So the effective (dynamic) impedance is Z = 1/Y = (L/C)/R = L/(RC), a pure resistance that is large when R is small. (The booklet leaves out the word "impedance"; it is added in square brackets.)

  2. Q2 · Network Theory · Network Laws & Theorems

    The voltage across 5 A source in the given circuit is

    Figure for question 2
    1. 17.5 volt
    2. 25 volt
    3. 15 volt
    4. 20 volt
    Show answer

    Answer: (1) 17.5 volt

    Take the bottom wire as reference and let V be the top-right node (the node shared by the shunt 5 Ω and the 5 A source). KCL at that node: (V − 10)/5 + V/5 = 5 → 2V − 10 = 25 → V = 17.5 V, which is the voltage across the 5 A source.

  3. Q3 · Network Theory · AC Circuits & Resonance

    The current i(t) through a 10Ω resistor in series with an inductance is given by i(t) = 3 + 4 sin(100t + 45°) + 4sin(300t + 60°) Amperes. The rms value of the current and the power dissipated in the circuit are

    1. 40 A, 410W
    2. 10A, 350W
    3. 5A, 250W
    4. 11A, 250W
    Show answer

    Answer: (3) 5A, 250W

    For a sum of a dc term and sinusoids of different frequencies, I_rms = √(I_dc² + I₁²/2 + I₂²/2) = √(9 + 8 + 8) = √25 = 5 A. Only the resistor dissipates power (the inductance stores energy), so P = I_rms²R = 25 × 10 = 250 W.

  4. Q4 · Network Theory · Network Laws & Theorems

    An ideal voltage source and current sources are connected in parallel. This circuit has

    1. neither Thevenin nor Norton's equivalent
    2. both Thevinin and Norton's equivalent
    3. a Thevenin equivalent but not Norton's equivalent
    4. a Norton's equivalent but not Thevenin equivalent
    Show answer

    Answer: (3) a Thevenin equivalent but not Norton's equivalent

    An ideal voltage source fixes the terminal voltage whatever current sources are in parallel with it, so the combination is just that voltage source: a Thevenin equivalent with V_th = V and R_th = 0. A Norton equivalent would need I_N = V_th/R_th = V/0, which is infinite, so it does not exist.

  5. Q5 · Network Theory · Transients & Laplace Analysis

    A transient current in a network is i(t) = 2e⁻ᵗ − e⁻⁵ᵗ, t ≥ 0. The pole-zero configuration of I(s) is

    1. poles : 1,5 zeros : 9
    2. poles : −1, −5 zeros : −9
    3. poles : 2, −1 zeros : −1, −5
    4. poles : 2, −1 zeros: 1, 5
    Show answer

    Answer: (2) poles : −1, −5 zeros : −9

    I(s) = 2/(s + 1) − 1/(s + 5) = (2s + 10 − s − 1)/((s + 1)(s + 5)) = (s + 9)/((s + 1)(s + 5)). So the poles are at s = −1 and −5 and the zero is at s = −9.

  6. Q6 · Network Theory · Two-Port Networks & Network Synthesis

    F(s) = (s+1)(s+3)/(s(s+2)) represents an

    1. RC impedance and an RL admittance
    2. RL admittance
    3. RC impedance
    4. RC admittance
    Show answer

    Answer: (1) RC impedance and an RL admittance

    The poles (0, −2) and zeros (−1, −3) are simple, lie on the negative real axis and alternate, with a pole nearest the origin, and F(0) = ∞ > F(∞) = 1: these are the properties of an RC driving-point impedance, which are exactly those of an RL driving-point admittance. Expanding, F(s) = 1 + 1.5/s + 0.5/(s + 2): as an impedance this is 1 Ω in series with a 2/3 F capacitor and a parallel 2 F, 0.25 Ω section; as an admittance it is 1 S in parallel with a 2/3 H inductor and a branch of 2 H in series with 4 Ω. So it represents both.

  7. Q7 · Network Theory · Transients & Laplace Analysis

    The transfer function of a system Z(s) = V(s)/I(s)= s/(s+3). The system is at rest for t < 0. What will be the value of v(t) for t ≥ 0, if i(t) = 3 u(t), where u(t) is a step function

    1. e⁻ᵗ
    2. 4 e⁻ᵗ
    3. 2 e⁻³ᵗ
    4. 3e⁻³ᵗ
    Show answer

    Answer: (4) 3e⁻³ᵗ

    I(s) = 3/s, so V(s) = Z(s)I(s) = (s/(s + 3)) × (3/s) = 3/(s + 3). Taking the inverse Laplace transform, v(t) = 3e⁻³ᵗ for t ≥ 0.

  8. Q8 · Electronic Devices & IC Technology · Semiconductor Physics

    Doping materials are called impurities because they

    1. change the temperature of the material
    2. alter the crystal structure of the pure semiconductor
    3. change the chemical properties of semiconductors
    4. decrease the number of charge carriers
    Show answer

    Answer: (3) change the chemical properties of semiconductors

    Dopants are foreign (group III or group V) atoms added to an otherwise pure (intrinsic) semiconductor, so the material is no longer chemically pure: its chemical make-up and hence its properties change, which is why they are called impurities. They sit substitutionally in the lattice in parts per million, so the crystal structure is not altered, and they increase (not decrease) the number of charge carriers.

  9. Q9 · Electronic Devices & IC Technology · IC Fabrication

    In IC technology, dry oxidation as compared to wet oxidation produces

    1. superior quality oxide with a lower growth rate
    2. superior quality oxide with a higher growth rate
    3. inferior quality oxide with a lower growth rate
    4. inferior quality oxide with a higher growth rate
    Show answer

    Answer: (1) superior quality oxide with a lower growth rate

    Dry oxidation (Si + O₂ → SiO₂) grows a dense, low-defect oxide of high quality, used for MOS gate oxides, but it grows slowly. Wet oxidation (Si + 2H₂O → SiO₂ + 2H₂) is much faster because H₂O diffuses through the oxide more easily, but the oxide is less dense and is used for thick field oxides.

  10. Q10 · Analog Circuits · Transistor Amplifiers & Biasing

    In a transistor h_fe =50, h_ie=830Ω, h_oe=10⁻⁴ mho. Its output resistance when used in CB configuration is about

    1. 2 MΩ
    2. 2.5 MΩ
    3. 500Ω
    4. 500 KΩ
    Show answer

    Answer: (4) 500 KΩ

    The common-base output admittance is h_ob = h_oe/(1 + h_fe) = 10⁻⁴/51 ≈ 1.96 × 10⁻⁶ mho. So the CB output resistance is 1/h_ob = 51/10⁻⁴ = 510 kΩ, i.e. about 500 kΩ, much higher than the CE value 1/h_oe = 10 kΩ.

  11. Q11 · Analog Circuits · Op-Amps & Linear ICs

    The circuit shown in the figure can be used as a

    Figure for question 11
    1. full wave rectifier
    2. voltage to frequency converter
    3. logarithmic amplifier
    4. frequency to voltage converter
    Show answer

    Answer: (3) logarithmic amplifier

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  12. Q12 · Network Theory · Network Laws & Theorems

    KCL is a consequences of law of conservation of

    1. flux
    2. energy
    3. potential
    4. charge
    Show answer

    Answer: (4) charge

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  13. Q13 · Network Theory · Network Laws & Theorems

    When a source is delivering maximum power to a load, the efficiency of the circuit

    1. is always 50%
    2. is always 75%
    3. depends on the circuit parameters
    4. is always 100%
    Show answer

    Answer: (1) is always 50%

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  14. Q14 · Network Theory · Network Laws & Theorems

    In the Thevenin equivalent circuit, V_th equals

    1. short-circuit terminal voltage
    2. open-circuit terminal voltage
    3. net voltage available in the circuit
    4. voltage of the source
    Show answer

    Answer: (2) open-circuit terminal voltage

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  15. Q15 · Network Theory · AC Circuits & Resonance

    For a series RLC circuit, the power factor at the lowest half power frequency is

    1. 0.707 lagging
    2. 0.5 leading
    3. 1.0
    4. 0.707 leading
    Show answer

    Answer: (4) 0.707 leading

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  16. Q16 · Network Theory · AC Circuits & Resonance

    A series RLC circuit has a resonance frequency of 1 kHz and a quality factor Q = 100. If each of R, L and C is doubled from its original value, the new Q of the circuit

    1. 200
    2. 100
    3. 25
    4. 50
    Show answer

    Answer: (4) 50

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  17. Q17 · Network Theory · Transients & Laplace Analysis

    An inductance and a capacitance are connected in series. If a unit step voltage is applied across the combination, then the initial and final currents in the circuit will be

    1. 0, ∞ respectively
    2. 0, 0 respectively
    3. ∞, ∞ respectively
    4. ∞, 0 respectively
    Show answer

    Answer: (2) 0, 0 respectively

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  18. Q18 · Network Theory · Transients & Laplace Analysis

    The Laplace transform of the function i(t) is I(s) = (10s + 4)/(s(s+1)(s² + 4s + 5)). Its final value will be

    1. 5/4
    2. 4/5
    3. 5
    4. 4
    Show answer

    Answer: (2) 4/5

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  19. Q19 · Network Theory · Two-Port Networks & Network Synthesis

    The network function F(s) = (s+2)/((s+1)(s+3)) Represents an

    1. RC admittance and an RL impedance
    2. RC impedance
    3. RL impedance
    4. RC impedance and an RL admittance
    Show answer

    Answer: (4) RC impedance and an RL admittance

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  20. Q20 · Network Theory · Two-Port Networks & Network Synthesis

    If a two-port network is reciprocal as well as symmetrical, which one of the following conditions true

    1. Z_12 = Z_21 and Z_11 = Z_22
    2. Z_11 = Z_21 and Z_12 = Z_22
    3. Y_11 = Y_21 and Y_12 = Y_22
    4. AD + BC = 1 and A = C
    Show answer

    Answer: (1) Z_12 = Z_21 and Z_11 = Z_22

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  21. Q21 · Electronic Devices & IC Technology · Semiconductor Physics

    An intrinsic semiconductor at absolute zero temperature

    1. has large number of holes
    2. has a large number of electrons
    3. behaves like an insulator
    4. behaves like a metallic conductor
    Show answer

    Answer: (3) behaves like an insulator

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  22. Q22 · Electronic Devices & IC Technology · Diodes & Transistors

    A diode clamper also referred to as a

    1. series rectifier
    2. series clamper
    3. shunt rectifier
    4. shunt clamper
    Show answer

    Answer: (3) shunt rectifier

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  23. Q23 · Electronic Devices & IC Technology · Diodes & Transistors

    The Ebers-Moll model is applicable to

    1. Junction FET
    2. UJT
    3. NMOS
    4. BJT
    Show answer

    Answer: (4) BJT

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  24. Q24 · Digital Electronics & Microprocessors · Logic Families, Memories & Converters

    When the frequency of the input signal to a CMOS gate is increased, the average power dissipation

    1. does not change
    2. increases
    3. decreases
    4. decreases exponentially
    Show answer

    Answer: (2) increases

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  25. Q25 · Electronic Devices & IC Technology · IC Fabrication

    Photo masking

    1. controls the depth of diffusion
    2. is used to prevent ambient light shining on the silicon slice
    3. is used in the process to remove selected regions of silicon oxide
    4. reduce the size of the circuit elements
    Show answer

    Answer: (3) is used in the process to remove selected regions of silicon oxide

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  26. Q26 · Analog Circuits · Transistor Amplifiers & Biasing

    The self bias is used in amplifiers to

    1. reduce the cost of the circuit
    2. reduce the dc base current
    3. make the operating point almost independent of β
    4. limit the input ac signal going to the base terminal
    Show answer

    Answer: (3) make the operating point almost independent of β

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  27. Q27 · Analog Circuits · Transistor Amplifiers & Biasing

    The h- parameter equivalent circuit of a BJT is valid for

    1. low frequency, large signal operation
    2. low frequency, small signal operation
    3. high frequency, small signal operation
    4. high frequency, large signal operation
    Show answer

    Answer: (2) low frequency, small signal operation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  28. Q28 · Analog Circuits · Feedback, Oscillators & Power Supplies

    In a centre-tap full wave rectifier, V_m is the peak voltage between the centre-tap and one of the secondary. The maximum voltage across the reverse biased diode is

    1. V_m
    2. 2 V_m
    3. V_m/2
    4. 3 V_m
    Show answer

    Answer: (2) 2 V_m

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  29. Q29 · Electronic Devices & IC Technology · Diodes & Transistors

    The circuit shown in figure is a

    Figure for question 29
    1. positive peak clipper
    2. positive clamper
    3. differentiator
    4. negative clamper
    Show answer

    Answer: (2) positive clamper

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  30. Q30 · Analog Circuits · Transistor Amplifiers & Biasing

    The gain of a transistor amplifier falls at high frequency due to the

    1. coupling capacitor at the output
    2. skin effect
    3. internal capacitances of device
    4. coupling capacitor at the input
    Show answer

    Answer: (3) internal capacitances of device

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  31. Q31 · Analog Circuits · Transistor Amplifiers & Biasing

    Darlington pair consists of the following two stages

    1. both CE
    2. CE and CB
    3. CE and CC
    4. both CC
    Show answer

    Answer: (4) both CC

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  32. Q32 · Analog Circuits · Feedback, Oscillators & Power Supplies

    The voltage gain of an amplifier is 100. On applying negative feedback with β = 0.03, its gain will reduce to

    1. 50
    2. 2.5
    3. 3.0
    4. 25
    Show answer

    Answer: (4) 25

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  33. Q33 · Analog Circuits · Transistor Amplifiers & Biasing

    The main function of the transformer used in the output of a power amplifier is

    1. to step up the voltage
    2. to step down the voltage
    3. to match the load impedance with dynamic output resistance of the transistor
    4. to increase voltage gain
    Show answer

    Answer: (3) to match the load impedance with dynamic output resistance of the transistor

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  34. Q34 · Analog Circuits · Transistor Amplifiers & Biasing

    The bandwidth of a double tuned transformer coupled amplifier can be adjusted by varying the

    1. coupling coefficient
    2. value of the inductance
    3. value of the emitter biasing resistance
    4. value of resistance
    Show answer

    Answer: (1) coupling coefficient

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  35. Q35 · Analog Circuits · Transistor Amplifiers & Biasing

    Crossover distortion results in

    1. class B output stage
    2. common emitter output stage
    3. class AB output stage
    4. class A output stage
    Show answer

    Answer: (1) class B output stage

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  36. Q36 · Analog Circuits · Feedback, Oscillators & Power Supplies

    In transistor series voltage regulator the transistor behaves like a variable

    1. resistor
    2. capacitor
    3. inductor
    4. resistor and capacitor
    Show answer

    Answer: (1) resistor

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  37. Q37 · Network Theory · Network Laws & Theorems

    If b is the number of branches and n the number of nodes in a connected graph, the number of links corresponding to any tree of the graph

    1. b − n − 1
    2. b − n + 1
    3. n − b − 1
    4. n + 1 − b
    Show answer

    Answer: (2) b − n + 1

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  38. Q39 · Network Theory · Network Laws & Theorems

    Superposition theorem is not applicable to networks containing

    1. nonlinear elements
    2. dependent voltage sources
    3. dependent current sources
    4. transformers
    Show answer

    Answer: (1) nonlinear elements

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  39. Q40 · Network Theory · AC Circuits & Resonance

    In an RLC parallel circuit the impedance at resonance is

    1. ∞
    2. minimum
    3. maximum
    4. zero
    Show answer

    Answer: (3) maximum

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  40. Q41 · Network Theory · Two-Port Networks & Network Synthesis

    Any two-port network having a 6dB loss will give

    1. an output power which is 0.707 of the input power
    2. an output power which is one quarter of the input power
    3. an output power which is one half of the input power
    4. an output voltage which is 0.707 of the input voltage
    Show answer

    Answer: (2) an output power which is one quarter of the input power

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  41. Q42 · Network Theory · Two-Port Networks & Network Synthesis

    For a reciprocal network, the two port h- parameters are related as follows

    1. h_12 = h_21
    2. h_11h_22 − h_21h_12 = 1
    3. h_11h_22 − h_21h_12 = −1
    4. h_12 = − h_21
    Show answer

    Answer: (4) h_12 = − h_21

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  42. Q43 · Electronic Devices & IC Technology · Diodes & Transistors

    Which of the following is not associated with a PN junction?

    1. depletion capacitance
    2. junction capacitance
    3. charge storage capacitance
    4. channel length modulation
    Show answer

    Answer: (4) channel length modulation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  43. Q44 · Electronic Devices & IC Technology · Diodes & Transistors

    Zener diode break down voltage———with temperature

    1. decreases
    2. constant
    3. increases
    4. may increase or decrease
    Show answer

    Answer: (1) decreases

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  44. Q45 · Electronic Devices & IC Technology · Diodes & Transistors

    The output V-I characteristics of an enhancement type MOSFET has

    1. an ohmic region at low voltage value followed by a saturation region at higher voltages
    2. an ohmic region at large voltage values preceded by a saturation region at lower voltages
    3. only an ohmic region
    4. only a saturation region
    Show answer

    Answer: (1) an ohmic region at low voltage value followed by a saturation region at higher voltages

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  45. Q46 · Analog Circuits · Transistor Amplifiers & Biasing

    Typical value of h_ie is

    1. 1KΩ
    2. 1 Ω
    3. 100 KΩ
    4. 50 Ω
    Show answer

    Answer: (1) 1KΩ

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  46. Q48 · Analog Circuits · Op-Amps & Linear ICs

    The ideal Op-Amp has following characteristics

    1. R_i = ∞, A = ∞, R_0 = 0
    2. R_i = 0, A = ∞, R_0 = 0
    3. R_i = ∞, A = ∞, R_0 = ∞
    4. R_i = 0, A = ∞, R_0 = ∞
    Show answer

    Answer: (1) R_i = ∞, A = ∞, R_0 = 0

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  47. Q49 · Analog Circuits · Feedback, Oscillators & Power Supplies

    In a half-wave rectifier, if an a.c supply is 60Hz, then the a.c ripple at output will be

    1. 6Hz
    2. 30Hz
    3. 60Hz
    4. 120Hz
    Show answer

    Answer: (3) 60Hz

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  48. Q50 · Analog Circuits · Transistor Amplifiers & Biasing

    Maximum theoretical conversion efficiency of class B amplifier is

    1. 7.85%
    2. 25%
    3. 50%
    4. 78.5%
    Show answer

    Answer: (4) 78.5%

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  49. Q51 · Digital Electronics & Microprocessors · Number Systems & Logic Gates

    In a logic equation A(A + B̄C̄ + C) + B̄(C̄ + Ā + BC) + (A + B̄C + AC̄) = 1, if C = Ā then

    1. A + B = 1
    2. Ā + B = 1
    3. A + B̄ = 1
    4. A = 1
    Show answer

    Answer: (3) A + B̄ = 1

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  50. Q52 · Digital Electronics & Microprocessors · Number Systems & Logic Gates

    The maximum positive and negative numbers which can be represented in 2's compliment form using n-bit are

    1. + (2ⁿ⁻¹ − 1), − (2ⁿ⁻¹ − 1)
    2. + (2ⁿ⁻¹ − 1), − 2ⁿ⁻¹
    3. + 2ⁿ⁻¹, −2ⁿ⁻¹
    4. none
    Show answer

    Answer: (2) + (2ⁿ⁻¹ − 1), − 2ⁿ⁻¹

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  51. Q54 · Digital Electronics & Microprocessors · Combinational & Sequential Circuits

    In a positive edge triggered JK flip-flop, the present state Q_n is set to high (1). If the inputs J=A and K=B then next state Q_(n+1) will be

    1. B̄
    2. Ā
    3. A + B
    4. A
    Show answer

    Answer: (1) B̄

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  52. Q55 · Digital Electronics & Microprocessors · Combinational & Sequential Circuits

    In PLA both AND and OR arrays are

    1. Non-programmable
    2. Programmable
    3. 1 and 2
    4. None
    Show answer

    Answer: (2) Programmable

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  53. Q56 · Digital Electronics & Microprocessors · Logic Families, Memories & Converters

    Pick the wrong statement of CMOS

    1. Low power dissipation
    2. Poor Noise immunity
    3. High packing density
    4. Wide range of supply voltages
    Show answer

    Answer: (2) Poor Noise immunity

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  54. Q57 · Signals & Systems · Fourier, Laplace & Z-Transforms

    The signal e⁻ᵗu(t) is applied as input to an L-section RC lowpass filter with time-constant equal to 1. The energy spectral density at the output of the filter at the 3-db cutoff frequency of the filter is

    1. 1
    2. 0.5
    3. 0.25
    4. 1.5
    Show answer

    Answer: (3) 0.25

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  55. Q58 · Signals & Systems · Signals & LTI Systems

    Two LTI systems with impulse responses h_1(t) and h_2(t) are connected in series(cascade), the impulse response of the overall system is

    1. h_1(t) + h_2(t)
    2. h_1(t)h_2(t)/(h_1(t) + h_2(t))
    3. h_1(t)*h_2(t)
    4. h_1(t).h_2(t)
    Show answer

    Answer: (3) h_1(t)*h_2(t)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  56. Q59 · Signals & Systems · Signals & LTI Systems

    Which of the following system is causal?

    1. h(n) = n(½)ⁿ u(n+1)
    2. y(n) = x²(n) − x(n+1)
    3. y(n) = x(−n) + x(2n−1)
    4. h(n) = n(½)ⁿ u(n)
    Show answer

    Answer: (4) h(n) = n(½)ⁿ u(n)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  57. Q60 · Signals & Systems · Signals & LTI Systems

    Two parallel connected discrete time systems with impulse responses h_1(n) and h_2(n) can be replaced by a single equivalent discrete time system with impulse response,

    1. h_1(n) * h_2(n)
    2. h_1(n) + h_2(n)
    3. h_1(n) − h_2(n)
    4. h_1(n) * [h_1(n) + h_2(n)]
    Show answer

    Answer: (2) h_1(n) + h_2(n)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  58. Q61 · Signals & Systems · Fourier, Laplace & Z-Transforms

    For a stable LTI discrete time system, poles should lie ____ and unit circle should be ____

    1. Outside unit circle, included in ROC
    2. Inside unit circle, outside of ROC
    3. Inside unit circle, included in ROC
    4. Outside unit circle, outside of ROC
    Show answer

    Answer: (3) Inside unit circle, included in ROC

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  59. Q62 · Signals & Systems · Fourier, Laplace & Z-Transforms

    The discrete time Fourier transform of the signal, x(n) = 0.5^(n−1) u(n−1) is,

    1. e^(−jω)/(1 − 0.5e^(−jω))
    2. e^(−jω)(1 − 0.5e^(−jω))
    3. 0.5e^(−jω)/(1 − 0.5e^(−jω))
    4. 0.5e^(jω)/(1 − 0.5e^(−jω))
    Show answer

    Answer: (1) e^(−jω)/(1 − 0.5e^(−jω))

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  60. Q63 · Control Systems · Time Response & Stability

    The characteristic polynomial of a system q(s) = 2s⁵ + s⁴ + 4s³ + 2s² + 2s + 1. The system is

    1. Stable
    2. Marginally stable
    3. Unstable
    4. Oscillatory
    Show answer

    Answer: (3) Unstable

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  61. Q64 · Control Systems · Transfer Functions & Block Diagrams

    The system mode described by this equation X = [0, 1; 2, −3] x + [0; 1] u, y = [1, 1] x is

    1. Controllable and observable
    2. Controllable but not observable
    3. Observable but not controllable
    4. Neither controllable nor observable
    Show answer

    Answer: (1) Controllable and observable

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  62. Q65 · Digital Electronics & Microprocessors · Number Systems & Logic Gates

    The number of switching functions of 3 variables is

    1. 8
    2. 64
    3. 128
    4. 256
    Show answer

    Answer: (4) 256

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  63. Q66 · Digital Electronics & Microprocessors · Combinational & Sequential Circuits

    In JK Flip flop if we input K with the inverted from of what we input J, the resulted flip flop is

    1. SR flip flop
    2. JK flip-flop itself
    3. D flip flop
    4. T flip flop
    Show answer

    Answer: (3) D flip flop

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  64. Q67 · Digital Electronics & Microprocessors · Microprocessors & Microcontrollers

    How many and what are the machine cycles needed for execution of PUSH B?

    1. 2, fetch and memory write
    2. 3, fetch and 2 memory write
    3. 3, fetch, memory write and read
    4. 3, fetch and 2 memory read
    Show answer

    Answer: (2) 3, fetch and 2 memory write

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  65. Q68 · Digital Electronics & Microprocessors · Logic Families, Memories & Converters

    For successive approximation with N output bits, number of clocks required is

    1. N + 2 or N
    2. 2N + 1
    3. 2ᴺ
    4. 2ᴺ − 1
    Show answer

    Answer: (1) N + 2 or N

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  66. Q69 · Digital Electronics & Microprocessors · Combinational & Sequential Circuits

    The minimum number of flip-flops required in a counter to count 60 pulses is

    1. 4
    2. 6
    3. 8
    4. 10
    Show answer

    Answer: (2) 6

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  67. Q70 · Digital Electronics & Microprocessors · Microprocessors & Microcontrollers

    What is the addressing mode used in instruction LXI B0345 H ?

    1. Direct
    2. Indirect
    3. Indexed
    4. Immediate
    Show answer

    Answer: (4) Immediate

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  68. Q71 · Digital Electronics & Microprocessors · Microprocessors & Microcontrollers

    The 8255 programmable peripheral interface consist of ____ 8-bit ports

    1. 2
    2. 3
    3. 4
    4. 6
    Show answer

    Answer: (2) 3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  69. Q72 · Digital Electronics & Microprocessors · Microprocessors & Microcontrollers

    Ready signal is used to

    1. Synchronize fast peripherals with microprocessor
    2. Synchronize slow peripherals with microprocessor
    3. Send request to microprocessor for direct memory access
    4. Send request to microprocessor for interrupt subroutines
    Show answer

    Answer: (2) Synchronize slow peripherals with microprocessor

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  70. Q73 · Digital Electronics & Microprocessors · Microprocessors & Microcontrollers

    When the reset pin is activated, the program counter is loaded with

    1. 1000H
    2. 2000H
    3. 3000H
    4. 0000H
    Show answer

    Answer: (4) 0000H

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  71. Q74 · Digital Electronics & Microprocessors · Combinational & Sequential Circuits

    An ‘N’ bit Johnson counter can count ____ states

    1. N
    2. 2N
    3. N−1
    4. 2N−1
    Show answer

    Answer: (2) 2N

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  72. Q75 · Digital Electronics & Microprocessors · Number Systems & Logic Gates

    The 2's compliment of the given number 1011001 is

    1. 1011000H
    2. 1011001H
    3. 1010110H
    4. None.
    Show answer

    Answer: (4) None.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  73. Q76 · Digital Electronics & Microprocessors · Combinational & Sequential Circuits

    The n-stage register results in a delay of

    1. (n−1) T
    2. 2nT
    3. n²T
    4. nT/2
    Show answer

    Answer: (1) (n−1) T

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  74. Q77 · Digital Electronics & Microprocessors · Number Systems & Logic Gates

    n-bit variables have 2ⁿ possible combinations and each of these possible combinations is called

    1. Maxterm
    2. Minterm
    3. Product of sum
    4. Sum of product
    Show answer

    Answer: (2) Minterm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  75. Q78 · Digital Electronics & Microprocessors · Number Systems & Logic Gates

    What is the gray code of (10010)_2

    1. 10011
    2. 00100
    3. 11111
    4. 11011
    Show answer

    Answer: (4) 11011

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  76. Q79 · Digital Electronics & Microprocessors · Number Systems & Logic Gates

    The 2's complement representation of the decimal number −4 is

    1. 1000
    2. 1100
    3. 1011
    4. 1010
    Show answer

    Answer: (2) 1100

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  77. Q80 · Signals & Systems · Fourier, Laplace & Z-Transforms

    The Fourier series of a periodic signal x(t) with period T will not converge if

    1. |x(t)| is not finite at all values of t
    2. x(t) has more than one maxima in one period T
    3. x(t) is not continuous at all points
    4. x(t) is not a band limited signal
    Show answer

    Answer: (1) |x(t)| is not finite at all values of t

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  78. Q81 · Signals & Systems · Signals & LTI Systems

    When the input to an LTI system is a unit step function, the output is a bounded signal. Which of the following inferences is correct?

    1. The system is not necessarily stable
    2. The system is not definitely stable
    3. The system is definitely unstable
    4. None of the above
    Show answer

    Answer: (4) None of the above

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  79. Q82 · Signals & Systems · Signals & LTI Systems

    Which of the following signal is an example for deterministic signal?

    1. step
    2. ramp
    3. exponential
    4. all of the above
    Show answer

    Answer: (4) all of the above

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  80. Q83 · Signals & Systems · Fourier, Laplace & Z-Transforms

    The Z-transform of a⁻ⁿ u(−n−1) is,

    1. −z/(z − 1/a)
    2. z/(z − 1/a)
    3. z/(z − a)
    4. −z/(z − a)
    Show answer

    Answer: (1) −z/(z − 1/a)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  81. Q84 · Signals & Systems · Fourier, Laplace & Z-Transforms

    The ROC of the signal x(n) = aⁿ for −5 < n < 5 is,

    1. entire z-plane
    2. entire z-plane except z=0 and z=∞
    3. entire z-plane except z=0
    4. entire z-plane except z=∞
    Show answer

    Answer: (2) entire z-plane except z=0 and z=∞

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  82. Q85 · Signals & Systems · Fourier, Laplace & Z-Transforms

    If a signal is folded about the origin in time, then its

    1. magnitude spectrum undergoes change in sign
    2. phase spectrum undergoes change in sign
    3. magnitude remains unchanged
    4. both 2 and 3
    Show answer

    Answer: (4) both 2 and 3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  83. Q86 · Control Systems · Time Response & Stability

    If s³+3s²+4s+A=0, then all the roots of this equation are in the left half plane provide that

    1. A > 12
    2. −3 < A < 4
    3. 0 < A < 12
    4. 5 < A < 12
    Show answer

    Answer: (3) 0 < A < 12

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  84. Q87 · Control Systems · Frequency Response & Compensation

    The gain margin of the system with open loop transfer function G(s)H(s) = 2(1+s)/s²

    1. ∞
    2. 0
    3. 1
    4. −∞
    Show answer

    Answer: (2) 0

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  85. Q88 · Control Systems · Frequency Response & Compensation

    The Nyquist plot of a loop transfer function G(jω)H(jω) of a system encloses the (−1, j0) point, the gain margin of the system is

    1. Less than zero
    2. Zero
    3. Greater than zero
    4. Infinity
    Show answer

    Answer: (1) Less than zero

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  86. Q89 · Digital Electronics & Microprocessors · Number Systems & Logic Gates

    Number of NAND gates required for Ex-NOR implementation

    1. 4
    2. 6
    3. 5
    4. 8
    Show answer

    Answer: (3) 5

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  87. Q90 · Digital Electronics & Microprocessors · Combinational & Sequential Circuits

    To implement n-bit parallel adder requires ____ Full adders

    1. n
    2. n − 1
    3. n+1
    4. none
    Show answer

    Answer: (1) n

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  88. Q91 · Digital Electronics & Microprocessors · Logic Families, Memories & Converters

    The most widely used bipolar technology for digital ICs

    1. DTL
    2. TTL
    3. ECL
    4. None
    Show answer

    Answer: (2) TTL

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  89. Q92 · Digital Electronics & Microprocessors · Combinational & Sequential Circuits

    Output of JK flip flop toggles when

    1. J=1, K=0
    2. J=0, K=1
    3. J=1, K=1
    4. J=0, K=0
    Show answer

    Answer: (3) J=1, K=1

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  90. Q93 · Digital Electronics & Microprocessors · Microprocessors & Microcontrollers

    The word size of 8085 microprocessor is

    1. 4-bit
    2. 16-bit
    3. 20-bit
    4. 8-bit
    Show answer

    Answer: (4) 8-bit

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  91. Q94 · Digital Electronics & Microprocessors · Number Systems & Logic Gates

    The octal equivalent of the decimal number 375 is.

    1. 560
    2. 567
    3. 565
    4. none
    Show answer

    Answer: (2) 567

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  92. Q95 · Digital Electronics & Microprocessors · Logic Families, Memories & Converters

    Fan-out for the 74 series is

    1. 4
    2. 5
    3. 8
    4. 10
    Show answer

    Answer: (4) 10

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  93. Q96 · Digital Electronics & Microprocessors · Combinational & Sequential Circuits

    Multiplexer can be named as

    1. Data Selector
    2. One to many Circuit
    3. Serial to parallel converter
    4. None
    Show answer

    Answer: (1) Data Selector

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  94. Q97 · Signals & Systems · Signals & LTI Systems

    The fundamental period T of a periodic-continuous time signal x(t), is

    1. the smallest positive constant satisfying the relation x(t) = x(t+mT) for every t and any integer m
    2. the positive constant satisfying the relation x(t) = x(t+mT) for every t and any integer m
    3. the largest positive constant satisfying the relation x(t) = x(t+mT) for any t and any integer m
    4. the smallest positive integer satisfying the relation x(t) = x(t+mT) for any t and any m
    Show answer

    Answer: (1) the smallest positive constant satisfying the relation x(t) = x(t+mT) for every t and any integer m

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  95. Q98 · Digital Electronics & Microprocessors · Microprocessors & Microcontrollers

    An instruction used to set the carry flag in a computer can be classified as

    1. Data transfer
    2. Arithmetic
    3. Program control
    4. Logical Instruction
    Show answer

    Answer: (4) Logical Instruction

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  96. Q99 · Signals & Systems · Signals & LTI Systems

    It is possible to compute the cross-correlation R_xy(τ) between two signals x(t) and y(t) directly from their convolution provided

    1. x(t) has even symmetry
    2. x(t) has odd symmetry
    3. y(t) has odd symmetry
    4. y(t) has even symmetry
    Show answer

    Answer: (4) y(t) has even symmetry

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  97. Q100 · Control Systems · Frequency Response & Compensation

    The transfer function of a phase lead controller is (1+3Ts)/(1+Ts), the maximum value of phase provided by this controller

    1. 90°
    2. 60°
    3. 45°
    4. 30°
    Show answer

    Answer: (4) 30°

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  98. Q101 · Analog Communication · Noise & Random Processes

    A random variable is uniformly distributed between 3 and 6. Its variance is

    1. 0.75
    2. 0.25
    3. 0.5
    4. 1
    Show answer

    Answer: (1) 0.75

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  99. Q102 · Signals & Systems · Sampling & Digital Signal Processing

    x(t)=3 cos²250πt. This signal is sampled at regular intervals of T seconds. The maximum value of T for which x(t) may be recovered from the sampled version without any distortion, is equal to

    1. 1 ms
    2. 2 ms
    3. 4 ms
    4. 0.5 ms
    Show answer

    Answer: (2) 2 ms

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  100. Q103 · Digital Communication · Sampling, PCM & Delta Modulation

    A message signal with its amplitude uniformly distributed between −2 V and +2 V is transmitted by a 4-bit binary PCM system. The (SNR)_q is equal to

    1. 256
    2. 1024
    3. 512
    4. 768
    Show answer

    Answer: (1) 256

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  101. Q104 · Digital Communication · Digital Modulation & Detection

    In a 16-ary PSK, the symbol rate is 10 kbps. The bit rate is

    1. 160 kbps
    2. 40 kbps
    3. 2.5 kbps
    4. (10/16) kbps
    Show answer

    Answer: (2) 40 kbps

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  102. Q105 · Digital Communication · Digital Modulation & Detection

    For any 4-ary FSK, the signal set is given by s_k(t) = √(2E/T) cos[(π/4)(n+k)t] ; 0 ≤ t ≤ T k=1,2,3,4 The dimension of its signal space is

    1. 1
    2. 2
    3. 3
    4. 4
    Show answer

    Answer: (4) 4

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  103. Q106 · Analog Communication · Amplitude Modulation & Receivers

    In the filter method of generation of SSB-SC, in order to make the filter specifications less stringent,

    1. it is ensured that the modulating signal has no high-frequency components
    2. a high-frequency carrier is used initially for generating the DSB-SC signal
    3. only those modulating signals which have high dc and low frequency content are used
    4. a low-frequency carrier is used initially for generating the DSB-SC signal
    Show answer

    Answer: (4) a low-frequency carrier is used initially for generating the DSB-SC signal

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  104. Q107 · Analog Communication · Amplitude Modulation & Receivers

    The occurrence of double spotting indicates

    1. that the IF is too high
    2. that the selectivity is poor
    3. that image rejection capability of the receiver is inadequate
    4. that the local oscillator frequency is less than that of the incoming signal
    Show answer

    Answer: (3) that image rejection capability of the receiver is inadequate

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  105. Q108 · Microwaves & Antennas · Waveguides & Cavity Resonators

    If in a rectangular waveguide for which a=2b, the cutoff frequency for TE_02 mode is 12GHz, the cutoff frequency for TM_11 mode is

    1. 3GHz
    2. 3√5 GHz
    3. 12 GHz
    4. 6√5 GHz
    Show answer

    Answer: (2) 3√5 GHz

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  106. Q109 · Electromagnetics & Transmission Lines · Vector Calculus & Electrostatics

    An electric potential field is produced by point charges 1μC and 4μC located at (−2,1,5) and (1,3,−1), respectively. The energy stored in the field is

    1. 2.57mJ
    2. 5.14mJ
    3. 10.28mJ
    4. None of these
    Show answer

    Answer: (2) 5.14mJ

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  107. Q110 · Electromagnetics & Transmission Lines · Wave Propagation

    A plane wave propagates in water (ε_r = 81). If the peak electric field is 20π V/m, then the Peak magnetic field intensity will be

    1. 1.5 A/m
    2. 5.0 A/m
    3. 10 π A/m
    4. 20 A/m
    Show answer

    Answer: (1) 1.5 A/m

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  108. Q111 · Electromagnetics & Transmission Lines · Wave Propagation

    Wave propagating in +Z direction, E is given E_x = 2cos t, E_y = 2cos(t + 90°). The wave is

    1. Linear polarized
    2. right circular polarized
    3. left circular polarized
    4. elliptically polarized
    Show answer

    Answer: (3) left circular polarized

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  109. Q112 · Electromagnetics & Transmission Lines · Wave Propagation

    If the velocity of EM wave in free space is 3 × 10⁸ m/s the velocity in a medium with ε_r = 4.5, μ_r = 2 Would be ........

    1. 1 × 10⁸ m/s
    2. 2 × 10⁶ m/s
    3. 2.5 × 10⁶ m/s
    4. 3 × 10⁸ m/s.
    Show answer

    Answer: (1) 1 × 10⁸ m/s

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  110. Q113 · Electromagnetics & Transmission Lines · Transmission Lines

    The input impedance of short circuited lossless line of length less than a quarter wavelength is........

    1. purely resistive
    2. purely inductive
    3. purely capacitive
    4. complex
    Show answer

    Answer: (2) purely inductive

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  111. Q114 · Electromagnetics & Transmission Lines · Transmission Lines

    A 50Ω lossless transmission line is terminated in 100Ω load and is excited by a 30MHz source of internal resistance of 50Ω. What should be the length of transmission line for maximum power transfer...............

    1. 5.0m
    2. 1.25m
    3. 2.5m
    4. 10.0m
    Show answer

    Answer: (2) 1.25m

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  112. Q115 · Microwaves & Antennas · Antennas & Arrays

    The electric field measured in the far field of an antenna at a distance of 50m is 1V/m. The average power density at a distance of 500 m from the antenna is

    1. 26.6 μW/m²
    2. 0.1 μW/m²
    3. 10 μW/m²
    4. 13.3 μW/m²
    Show answer

    Answer: (4) 13.3 μW/m²

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  113. Q116 · Analog Communication · Noise & Random Processes

    X is a random variable with variance σ_x². The variance of (X + a) where a is a constant is

    1. (σ_x+a)²
    2. σ_x²
    3. (σ_x² + a²)
    4. (σ_x² − a²)
    Show answer

    Answer: (2) σ_x²

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  114. Q117 · Analog Communication · Noise & Random Processes

    Two random processes X and Y are such that R_XY(t_1,t_2)=0 for all t_1 and t_2 and further one of them has zero mean. The processes are

    1. Uncorrelated but not orthogonal
    2. Orthogonal but not uncorrelated
    3. Statistically independent and orthogonal
    4. Orthogonal and uncorrelated
    Show answer

    Answer: (4) Orthogonal and uncorrelated

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  115. Q118 · Analog Communication · Noise & Random Processes

    Auto-correlation function R_X(τ) of a stationary process X(t) is

    1. a deterministic function with maximum value at τ=0
    2. a deterministic function which is periodic
    3. a stationary random process
    4. a periodic stationary process
    Show answer

    Answer: (1) a deterministic function with maximum value at τ=0

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  116. Q119 · Digital Communication · Sampling, PCM & Delta Modulation

    In the mid-tread type of quantizer, any input value lying between −0.5 to +0.5 is mapped into an output value of

    1. 0.5
    2. 1
    3. −0.5
    4. 0
    Show answer

    Answer: (4) 0

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  117. Q120 · Digital Communication · Digital Modulation & Detection

    One of the following bandpass digital modulation schemes is not suitable for transmission over nonlinear bandpass channels:

    1. FSK
    2. ASK
    3. PSK
    4. QFSK
    Show answer

    Answer: (2) ASK

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  118. Q121 · Digital Communication · Digital Modulation & Detection

    For M-ary PSK systems, the best trade-off between bandwidth efficiency and transmitted power is given for a value of M equal to

    1. 2
    2. 4
    3. 8
    4. 16
    Show answer

    Answer: (2) 4

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  119. Q122 · Digital Communication · Information Theory & Coding

    Mutual information I(X ; Y) between two discrete random variables X and Y is given by

    1. H(X) + H(Y) − H(X,Y)
    2. H(X) − H(Y| X)
    3. H(Y) − H(X | Y)
    4. H(X) + H(Y) + H(X,Y)
    Show answer

    Answer: (1) H(X) + H(Y) − H(X,Y)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  120. Q124 · Analog Communication · Amplitude Modulation & Receivers

    When sinusoidally modulated, the r.m.s. value of the current in the antenna of an AM transmitter increases 15% over its unmodulated value. The modulation index is

    1. 0.6
    2. 0.8
    3. 0.5
    4. 0.707
    Show answer

    Answer: (2) 0.8

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  121. Q125 · Analog Communication · Frequency & Phase Modulation

    For a frequency-modulated signal, the modulation index is doubled. The average power of the modulated signal is

    1. quadrupled
    2. doubled
    3. unaltered
    4. none of these
    Show answer

    Answer: (3) unaltered

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  122. Q126 · Analog Communication · Frequency & Phase Modulation

    A narrow band FM signal is generated using a phase modulator. The maximum deviation at the output of a phase modulator is about

    1. ± 250 Hz
    2. ± 1 kHz
    3. ± 1 MHz
    4. ± 25 Hz
    Show answer

    Answer: (4) ± 25 Hz

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  123. Q127 · Analog Communication · Amplitude Modulation & Receivers

    In an AM broadcast superheterodyne receiver, the local oscillator frequency is arranged to be higher than the incoming signal frequency in order to

    1. provide better image rejection
    2. make tracking easier
    3. produce the correct intermediate frequency, since a lower LO frequency will not permit generation of correct IF
    4. enable us to cover the required frequency range with the practically possible ratio of maximum to minimum values of the variable capacitors
    Show answer

    Answer: (4) enable us to cover the required frequency range with the practically possible ratio of maximum to minimum values of the variable capacitors

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  124. Q128 · Analog Communication · Noise & Random Processes

    At the output of the discriminator in a FM receiver, the PSD of the noise

    1. increases linearly with frequency
    2. decreases as the square of the frequency
    3. increases as the square of the frequency
    4. decreases linearly with frequency
    Show answer

    Answer: (3) increases as the square of the frequency

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  125. Q129 · Analog Communication · Frequency & Phase Modulation

    'Pre-emphasis' is

    1. boosting up of the high-frequency components of the message signal after detection in the receiver
    2. boosting up of the high-frequency components of the message signal at the transmitter before the modulation
    3. boosting up of the low-frequency components of the message signal after detection in the receiver
    4. boosting up of the low-frequency components of the message signal at the transmitter before the modulation
    Show answer

    Answer: (2) boosting up of the high-frequency components of the message signal at the transmitter before the modulation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  126. Q130 · Electromagnetics & Transmission Lines · Wave Propagation

    What is the major factor for determining whether a medium is free space, lossless dielectric, lossy dielectric, or good conductor?

    1. Attenuation constant
    2. Constitutive parameters (σ, ε, μ)
    3. Loss tangent
    4. Reflection coefficient
    Show answer

    Answer: (3) Loss tangent

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  127. Q131 · Electromagnetics & Transmission Lines · Transmission Lines

    For a lossy transmission line, the characteristic impedance does not depend on

    1. The operating frequency of the line
    2. The length of the line
    3. The load terminating the line
    4. both 2 and 3
    Show answer

    Answer: (4) both 2 and 3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  128. Q132 · Microwaves & Antennas · Waveguides & Cavity Resonators

    At microwave frequencies, we prefer waveguides to transmission lines for transporting EM energy because of all the following except that

    1. Losses in transmission lines are prohibitively large
    2. Waveguides have larger bandwidths and lower signal attenuation
    3. Transmission lines are larger than waveguides
    4. Transmission lines support only TEM mode
    Show answer

    Answer: (3) Transmission lines are larger than waveguides

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  129. Q133 · Microwaves & Antennas · Waveguides & Cavity Resonators

    When the electric field is at its maximum value, the magnetic energy of a cavity is

    1. At its maximum value
    2. At √2 of its maximum value
    3. At 1/2 of its maximum value
    4. Zero
    Show answer

    Answer: (4) Zero

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  130. Q135 · Electromagnetics & Transmission Lines · Vector Calculus & Electrostatics

    The divergence of vector A = [yz a_x + zx a_y + xy a_z] is

    1. rotational
    2. irrotational
    3. solenoidal
    4. both 2 & 3
    Show answer

    Answer: (4) both 2 & 3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  131. Q136 · Electromagnetics & Transmission Lines · Vector Calculus & Electrostatics

    For the vectors A = x a_x + y a_y and B = z a_z, so ∇.(A × B) is

    1. xz
    2. 0
    3. 1
    4. yz
    Show answer

    Answer: (2) 0

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  132. Q137 · Electromagnetics & Transmission Lines · Wave Propagation

    For free space E = 50 cos (10⁸t + β x), then the value of β ...................

    1. 0.333 rad/m
    2. 2/3
    3. 4/3
    4. 0.316
    Show answer

    Answer: (1) 0.333 rad/m

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  133. Q138 · Microwaves & Antennas · Antennas & Arrays

    The radiation pattern of loop antenna is

    1. cardioid
    2. semi-circle
    3. circle
    4. none of these
    Show answer

    Answer: (1) cardioid

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  134. Q139 · Microwaves & Antennas · Antennas & Arrays

    A Half wave dipole at a frequency of 100 MHz has a length of

    1. 100 m
    2. 3 m
    3. 1.5m
    4. 0.75
    Show answer

    Answer: (3) 1.5m

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  135. Q140 · Microwaves & Antennas · Antennas & Arrays

    Multiple number of antennas are arranged in arrays in order to enhance

    1. Both directivity and bandwidth
    2. Only directivity
    3. Only bandwidth
    4. Neither directivity nor bandwidth
    Show answer

    Answer: (2) Only directivity

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  136. Q141 · Analog Communication · Noise & Random Processes

    The variance σ² of a random variable X is given by

    1. E[X²]
    2. {E[X]}²
    3. E[X²]−{E[X]}²
    4. E[X²]+{E[X]}²
    Show answer

    Answer: (3) E[X²]−{E[X]}²

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  137. Q142 · Digital Communication · Sampling, PCM & Delta Modulation

    In a linear DM system,

    1. only granular noise will be present
    2. only slope overload noise will be present
    3. both granular noise and slope overload noise can be eliminated
    4. granular noise will be present but slope overload noise can be avoided by proper design
    Show answer

    Answer: (4) granular noise will be present but slope overload noise can be avoided by proper design

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  138. Q143 · Digital Communication · Digital Modulation & Detection

    P_e for a DPSK system is

    1. exp[−E_b/η]
    2. exp[−√(E_b/η)]
    3. (1/2) exp[−E_b/η]
    4. (1/2) exp[E_b/η]
    Show answer

    Answer: (3) (1/2) exp[−E_b/η]

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  139. Q144 · Analog Communication · Frequency & Phase Modulation

    The Foster-Seeley discriminator responds to the input FM signal's

    1. amplitude variations only
    2. amplitude as well as frequency variations
    3. frequency variations only
    4. variations neither in amplitude nor in frequency
    Show answer

    Answer: (2) amplitude as well as frequency variations

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  140. Q145 · Analog Communication · Amplitude Modulation & Receivers

    A superheterodyne AM broadcast receiver has an IF of 455 kHz. If it is tuned to a frequency of 700 kHz, the image frequency is

    1. 1610 kHz
    2. 1155 kHz
    3. 245 kHz
    4. 210 kHz
    Show answer

    Answer: (1) 1610 kHz

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  141. Q146 · Electromagnetics & Transmission Lines · Vector Calculus & Electrostatics

    Which is not an example of convection current?

    1. A moving charged belt
    2. Electronic movement in a vacuum tube
    3. An electron beam in a television tube
    4. Electric current flowing in a copper wire
    Show answer

    Answer: (4) Electric current flowing in a copper wire

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  142. Q147 · Electromagnetics & Transmission Lines · Vector Calculus & Electrostatics

    The value of electric field at a distance of 1 m from an infinite line charge density 1 C/m is

    1. 2πε₀
    2. ½πε₀
    3. ε₀/2π
    4. 2π/ε₀
    Show answer

    Answer: (2) ½πε₀

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  143. Q148 · Electromagnetics & Transmission Lines · Transmission Lines

    A line terminated in its characteristic impedance has a SWR of..............................

    1. infinity
    2. unity
    3. zero
    4. two
    Show answer

    Answer: (2) unity

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  144. Q149 · Microwaves & Antennas · Waveguides & Cavity Resonators

    Which one of the following modes has the highest cut-off wavelength in a rectangular waveguide?

    1. TE_10
    2. TE_01
    3. TM_01
    4. TM_11
    Show answer

    Answer: (1) TE_10

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  145. Q150 · Microwaves & Antennas · Antennas & Arrays

    In end fire array the principal direction of radiation

    1. Is perpendicular to the array axis
    2. Is perpendicular to the array axis and also to the plane containing the array elements
    3. Coincides with the direction of the array axis
    4. Is at 45 degrees to the direction of array axis.
    Show answer

    Answer: (3) Coincides with the direction of the array axis

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.