Learn with Anil · TGPSC AMVI (Assistant Motor Vehicles Inspector) PYQsPractise online →Subscribe ₹149

TGPSC AMVI 2023 Paper 2 Automobile Engineering question paper with answers

TSPSC Assistant Motor Vehicles Inspector 2023: Paper II (Automobile Engineering). Paper II: Automobile Engineering, computer-based test, 150 questions, 300 marks, 150 minutes, in English. Answers are from TSPSC's preliminary key; the final key may differ for a few questions. Held on 28 June 2023 (Notification 31/2022, CBRT, preliminary key). All four options with the answer from TSPSC's preliminary key (the final key was released only on candidates' response sheets), plus a short explanation for every question (the first 10 here, all of them in the app).

టీజీపీఎస్సీ అసిస్టెంట్ మోటార్ వెహికల్స్ ఇన్‌స్పెక్టర్ (AMVI) పేపర్-2 ఆటోమొబైల్ ఇంజనీరింగ్ 2023 ప్రశ్నపత్రం సమాధానాలతో

Attempt this paper · 150 min timerMake a topic-wise quiz

The correct answer to every question is free on this page, and so are the explanations of the first 10. For all 150 explanations, practise the paper in the app with the ₹149 All-in-One Pass, one payment for every exam on the site.

Subjects in this paper

All 150 questions

  1. Q1 · Thermodynamics & Heat Transfer · Thermodynamics

    Which of the following laws provides the basis for the temperature measurement?

    1. Zeroth law of thermodynamics
    2. First law of thermodynamics
    3. Second law of thermodynamics
    4. Boyle’s law
    Show answer

    Answer (TSPSC's preliminary key): (1) Zeroth law of thermodynamics

    The zeroth law states that if two bodies are each in thermal equilibrium with a third body, they are in thermal equilibrium with each other. This lets a thermometer (the third body) compare temperatures, so it is the basis of temperature measurement. The first law deals with conservation of energy, the second with the direction of heat flow and entropy, and Boyle's law with the P–V relation of a gas at constant temperature.

  2. Q2 · Thermodynamics & Heat Transfer · Thermodynamics

    For an isothermal process, which of the following is correct based on first law of thermodynamics?

    1. Heat added or rejected by the system equals to the work done by the system or work done on the system
    2. Work done by the system or work done on the system equals to the change in internal energy
    3. Heat added or rejected equals to the change in internal energy
    4. Heat added or rejected is equals to the sum of change in internal energy (not equal to zero) and work done by a system or work done on a system
    Show answer

    Answer (TSPSC's preliminary key): (1) Heat added or rejected by the system equals to the work done by the system or work done on the system

    By the first law, Q = ΔU + W. For an ideal gas the internal energy depends only on temperature, so in an isothermal process ΔU = 0 and Q = W: the heat added equals the work done by the system, and the work done on it is rejected as heat. Option 2 describes an adiabatic process (Q = 0), option 3 a constant-volume process (W = 0), and option 4 wrongly assumes ΔU ≠ 0.

  3. Q3 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In context of I.C. engines, what is the ratio of shaft energy to the energy available at the piston is called?

    1. Brake thermal efficiency
    2. Indicated thermal efficiency
    3. Mechanical efficiency
    4. Volumetric efficiency
    Show answer

    Answer (TSPSC's preliminary key): (3) Mechanical efficiency

    Mechanical efficiency ηm = brake power / indicated power, i.e. the useful output at the shaft divided by the power developed by the gases on the piston; the difference is lost in friction and pumping. Brake thermal efficiency compares brake power with the fuel energy supplied, indicated thermal efficiency compares indicated power with the fuel energy, and volumetric efficiency compares the charge actually inducted with the swept volume.

  4. Q4 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    For the I.C. engine, the ratio of total volume of the cylinder to clearance volume is called ______.

    1. clearance ratio
    2. efficiency
    3. expansion ratio
    4. compression ratio
    Show answer

    Answer (TSPSC's preliminary key): (4) compression ratio

    Compression ratio r = total cylinder volume / clearance volume = (Vs + Vc)/Vc, where Vs is the swept (stroke) volume and Vc the clearance volume left above the piston at TDC. Typical values are about 6–10 for petrol (SI) engines and 14–22 for diesel (CI) engines. The clearance ratio is Vc/Vs, and a higher compression ratio raises the air-standard efficiency.

  5. Q5 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is an advantage of reciprocating internal combustion engines over external combustion engines?

    1. Starting torque is high
    2. Weight to power ratio is generally low
    3. Require more space
    4. Cheaper fuel can be used
    Show answer

    Answer (TSPSC's preliminary key): (2) Weight to power ratio is generally low

    Because the fuel burns inside the cylinder, an IC engine needs no boiler, condenser or separate furnace, so it is compact, with a low weight-to-power ratio and higher overall efficiency, which suits vehicles. External combustion engines such as steam engines give high starting torque and can burn cheaper fuels like coal or wood, but they need more space; these are not advantages of IC engines.

  6. Q6 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is a function of Gudgeon pin in internal combustion engines?

    1. It acts as a face to receive gas pressure and transmits the thrust to connecting rod
    2. Provide a good sealing fit between the piston and cylinder
    3. It supports and allows the swivel of the connecting rod
    4. It reduces friction and takes care of the fluctuations of speed during a cycle
    Show answer

    Answer (TSPSC's preliminary key): (3) It supports and allows the swivel of the connecting rod

    The gudgeon (piston or wrist) pin joins the piston to the small end of the connecting rod and acts as a pivot, supporting the rod and allowing it to swivel as the crank turns. The piston crown receives the gas pressure, the piston rings give the seal between piston and cylinder, and the flywheel takes care of speed fluctuations during a cycle.

  7. Q7 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    During which of the following stroke, the flywheel stores energy so that it can supply the energy during the idle strokes?

    1. Suction stroke
    2. Expansion stroke
    3. Compression stroke
    4. Exhaust stroke
    Show answer

    Answer (TSPSC's preliminary key): (2) Expansion stroke

    In a four-stroke engine only the expansion (power) stroke produces work. During this stroke the flywheel absorbs the surplus energy as kinetic energy, its speed rising slightly, and gives it back during the idle suction, compression and exhaust strokes, keeping the crankshaft speed nearly uniform. A multi-cylinder engine overlaps power strokes and so needs a lighter flywheel.

  8. Q8 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    To allow the fresh charge to enter the cylinder, the inlet valve is opened in advance of the T.D.C position. The inlet valve is opened in advance by ______.

    1. 10° to 30°
    2. 50° to 60°
    3. 30° to 70°
    4. 0° to 10°
    Show answer

    Answer (TSPSC's preliminary key): (1) 10° to 30°

    In the actual valve timing of a four-stroke engine the inlet valve opens about 10°–30° of crank rotation before TDC, so that it is fully open when the suction stroke begins and the fresh charge can enter without restriction. It closes some degrees after BDC, using the inertia of the incoming charge to improve volumetric efficiency. The period when both valves are open near TDC is the valve overlap.

  9. Q9 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which one of the following factors affect the ignition timing of an internal combustion engine?

    1. Type of fuel
    2. Flywheel
    3. Piston material
    4. Cylinder material
    Show answer

    Answer (TSPSC's preliminary key): (1) Type of fuel

    The spark must occur early enough for the flame to burn the charge near TDC, and the time needed depends on the fuel: its octane rating (knock resistance) and burning rate decide how much spark advance can be used. Engine speed, load and mixture strength also affect the timing, which is why distributors have centrifugal and vacuum advance. The flywheel and the piston or cylinder materials do not decide ignition timing.

  10. Q10 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In a two-stroke engine, the process of clearing the cylinder after the expansion stroke is called ______.

    1. expansion
    2. scavenging
    3. compressing
    4. knocking
    Show answer

    Answer (TSPSC's preliminary key): (2) scavenging

    Scavenging is the sweeping out of the burnt gases from the cylinder of a two-stroke engine by the fresh charge or air entering through the transfer ports at the end of the expansion stroke. Common methods are cross-flow, loop (reverse-flow) and uniflow scavenging. Knocking is abnormal combustion, while expansion and compression are the normal working processes.

  11. Q11 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    What is the difference between indicated power and brake power of internal combustion engine?

    1. Total power
    2. Total available energy
    3. Total engine friction loss
    4. Total clearance
    Show answer

    Answer (TSPSC's preliminary key): (3) Total engine friction loss

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  12. Q12 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    The lowest temperature at which lubricating oil changes from a liquid state to plastic or solid state is called ______.

    1. cloud point
    2. emulsification point
    3. flash point
    4. pour point
    Show answer

    Answer (TSPSC's preliminary key): (1) cloud point

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  13. Q13 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which of the following is correct about cooling system of engines? I. The cooling system is provided on an engine because high temperatures reduce strength of piston and cylinder liner. II. The cooling system is provided on an engine because the overheated cylinder may lead to ignition lag in spark ignition engines.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (1) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  14. Q14 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following is correct regarding the diesel engines? I. Diesel engines uses an injector. II. There is no pre-ignition in diesel engines.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  15. Q15 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following is correct about grease? I. Grease is only used where there is a low bearing and shock loads. II. Lubricating grease is a solid to semi solid dispersion of a thickening agent in liquid lubricant.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  16. Q16 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following is correct about lubricating oils? I. Fatty oils exhibit less oiliness than mineral oils of the same viscosity. II. Multigrade oil are not required to change as per ambient temperature. III. Multigrade oil has short warming up period.

    1. Only I and II
    2. Only II
    3. Only II and III
    4. Only I and III
    Show answer

    Answer (TSPSC's preliminary key): (3) Only II and III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  17. Q17 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following is correct about the fuel injection system? I. It controls the rate of fuel injection. II. It filters the fuel. III. It controls the quantity of fuel to be injected.

    1. Only I and II
    2. Only II and III
    3. All I, II and III
    4. Only I and III
    Show answer

    Answer (TSPSC's preliminary key): (3) All I, II and III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  18. Q18 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following statement is correct regarding the effects of the air fuel mixtures in SI engine? I. If the air fuel mixture is slightly richer, mean effective pressure reaches its maximum value. II. The rate of fuel consumption is lowest for rich air fuel mixtures. III. By decreasing the richness of air fuel mixture, the proportion of CO₂ will decrease while those of CO with certain traces of unburnt H₂ will increase.

    1. Only I
    2. Only II and III
    3. Only I and III
    4. Only II
    Show answer

    Answer (TSPSC's preliminary key): (1) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  19. Q19 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Match the following statements in context of Spark Ignition engine.

    EffectCause
    I. Results in lowering of efficiency1. Running on the weakest air fuel mixture
    II. Results in high efficiency2. Running on the richest air fuel mixture
    III. Results in complete burning of the fuel3. During the cruising the air fuel mixture is approximately 16.5: 1 so that
    1. I-1, II-2, III-3
    2. I-2, II-1, III-3
    3. I-3, II-2, III-1
    4. I-2, II-3, III-1
    Show answer

    Answer (TSPSC's preliminary key): (2) I-2, II-1, III-3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  20. Q20 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Match the following fuel standard to its specialty.

    StandardSpecialty
    I. Iso-octane1. Very prone to knock
    II. Normal heptane2. Measure of ignition quality of diesel
    III. Cetane number3. Very high resistance to knock
    4. Anti knock performance under severe operating conditions
    1. I-4, II-2, III-3
    2. I-3, II-1, III-2
    3. I-1, II-3, III-4
    4. I-2, II-4, III-1
    Show answer

    Answer (TSPSC's preliminary key): (2) I-3, II-1, III-2

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  21. Q21 · Thermodynamics & Heat Transfer · Thermodynamics

    Which of the following is correctly matched pair regarding Clausius Inequality?

    1. δQ/T > 0 : Reversible cycle
    2. δQ/T = 0 : Irreversible cycle
    3. δQ/T < 0 : Irreversible cycle
    4. ΔS < 0 : Isolated system
    Show answer

    Answer (TSPSC's preliminary key): (3) δQ/T < 0 : Irreversible cycle

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  22. Q22 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    For same compression ratio and same heat input, which of the following order of efficiency is correct?

    1. η_duel > η_otto > η_diesel
    2. η_diesel > η_duel > η_otto
    3. η_duel > η_diesel > η_otto
    4. η_otto > η_duel > η_diesel
    Show answer

    Answer (TSPSC's preliminary key): (4) η_otto > η_duel > η_diesel

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  23. Q23 · Thermodynamics & Heat Transfer · Thermodynamics

    Arrange the following in an increasing order of value of n in PVⁿ = C. I. Constant pressure process II. Reversible adiabatic process III. Constant volume process IV. Isothermal process

    1. I, II, III, IV
    2. II, I, III, IV
    3. II, III, I, IV
    4. I, IV, II, III
    Show answer

    Answer (TSPSC's preliminary key): (4) I, IV, II, III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  24. Q24 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    For the four stroke otto engines, arrange the following in the correct order (first to last). I. The piston moves T.D.C. to B.D.C. and work is obtained after fuel is ignited. II. The piston moves B.D.C. to T.D.C. and compresses the air fuel mixture. III. The piston moves T.D.C. to B.D.C. and the inlet valve opens and air fuel mixture is sucked in. IV. The piston moves B.D.C. to T.D.C. and gases are made to escape through exhaust value.

    1. I, III, IV, II
    2. III, II, I, IV
    3. IV, II, I, III
    4. III, I, IV, II
    Show answer

    Answer (TSPSC's preliminary key): (2) III, II, I, IV

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  25. Q25 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    For a simple or elementary carburettor, arrange the following in a correct order (first to last). I. The velocity of air increases as it passes through the constriction at the venturi. II. Pressure decreases due to conversion of a portion of pressure head into kinetic energy. III. The piston moves down and the suction is produced in the cylinder and the induction manifold. IV. Due to pressure difference the jet issues fuel oil into air stream which vapourise forming air fuel mixture. V. The air flows through the carburettor.

    1. III, V, I, II, IV
    2. II, V, III, I, IV
    3. III, II, I, IV, V
    4. II, IV, III, V, I
    Show answer

    Answer (TSPSC's preliminary key): (1) III, V, I, II, IV

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  26. Q26 · Automobile Chassis & Transmission · Chassis & Body

    Which one of the following is an advantage of chassis with engine at front and drive is given to the wheels from rear of a vehicle?

    1. Increased efficiency of cooling system
    2. Inadequate space behind the rear seat for the luggage
    3. Elimination of propeller shaft
    4. The clutch, gear box and differential are usually made as one unit results in cost reduction
    Show answer

    Answer (TSPSC's preliminary key): (1) Increased efficiency of cooling system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  27. Q27 · Automobile Chassis & Transmission · Chassis & Body

    Which one of the following is a defect that may be found in chassis body of an automobile?

    1. Build up edges
    2. Broken welds
    3. Heat affected zone
    4. Toe out
    Show answer

    Answer (TSPSC's preliminary key): (2) Broken welds

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  28. Q28 · Automobile Chassis & Transmission · Chassis & Body

    For an automotive body, the magnitude of the drag force depends on ______.

    1. shear strength of automotive body
    2. magnitude of gravity
    3. velocity of automotive body
    4. strength of automotive body
    Show answer

    Answer (TSPSC's preliminary key): (3) velocity of automotive body

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  29. Q29 · Automobile Chassis & Transmission · Chassis & Body

    Which one of the following load acts on a chassis when a vehicle crosses a broken patch of road?

    1. Inertia load
    2. Short duration load
    3. Overload
    4. Impact load
    Show answer

    Answer (TSPSC's preliminary key): (2) Short duration load

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  30. Q30 · Automobile Chassis & Transmission · Steering & Suspension

    In which of the following the carriage unit of a car rolls about a transverse axis?

    1. Rolling
    2. Yawing
    3. Pitching
    4. Bending
    Show answer

    Answer (TSPSC's preliminary key): (3) Pitching

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  31. Q31 · Automobile Chassis & Transmission · Steering & Suspension

    Which one of the following is a function of the shackle in the context of a leaf spring?

    1. It helps in accommodating the change in the length of the spring.
    2. It is used to keep leaf spring in position on the axle.
    3. It is used to provide progressive stiffness against increasing load.
    4. It provides lubrication between the leaf spring.
    Show answer

    Answer (TSPSC's preliminary key): (1) It helps in accommodating the change in the length of the spring.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  32. Q32 · Automobile Chassis & Transmission · Clutch & Gearbox

    Which one of the following is a formula of the effective mean radius of a clutch for uniform pressure condition? (Where r₁ is inner radius and r₂ is outer radius).

    1. (1/3)[(r₂³ − r₁³)/(r₂² − r₁²)]
    2. (2/3)[(r₂³ − r₁³)/(r₂² − r₁²)]
    3. (r₂ + r₁)/2
    4. (2/3)[(r₁³ − r₂³)/(r₂² − r₁²)]
    Show answer

    Answer (TSPSC's preliminary key): (2) (2/3)[(r₂³ − r₁³)/(r₂² − r₁²)]

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  33. Q33 · Automobile Chassis & Transmission · Clutch & Gearbox

    In gear box, the device that is used to lock collar into the gear is called ______.

    1. reverse gear
    2. dog clutch
    3. electromagnetic clutch
    4. diaphragm clutch
    Show answer

    Answer (TSPSC's preliminary key): (2) dog clutch

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  34. Q34 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    The terms used for a combination of transmission and rear axles as a unit of a vehicle is ______.

    1. live axle
    2. tandem axle
    3. split axle
    4. trans axle
    Show answer

    Answer (TSPSC's preliminary key): (4) trans axle

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  35. Q35 · Automobile Chassis & Transmission · Wheels & Tyres

    If vehicle is taking a turn, what is the ratio of side force sustained to slip angle called?

    1. Camber force
    2. Cornering power
    3. Frictional power
    4. Camber angle
    Show answer

    Answer (TSPSC's preliminary key): (2) Cornering power

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  36. Q36 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Which of the following statement is correct about front axles of a vehicle? I. The front wheels are mounted on stub axles which are connected to the front axle by king pin. II. When brakes are provided at the front wheels the front axle withstand bending stresses only.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (1) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  37. Q37 · Automobile Chassis & Transmission · Steering & Suspension

    Which of the following is correct regarding steering mechanism of a vehicle? I. In order to avoid skidding, the two front wheels instantaneous centre should not coincide with the two rear wheels instantaneous centre. II. The fundamental equation for correct steering is cot φ − cot θ = c/b. Where, c = distance between the pivots of front axle. b = wheel base θ = inner wheel turning angle φ = outer wheel turning angle

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  38. Q38 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Which of the following statement is correct regarding transmission system of automobiles? I. The main advantage of an overdrive is prolonged engine life since the engine turns slower. II. A slip joint is attached to the driven yoke in order to increase or decrease the propeller shaft.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  39. Q39 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Which of the following statement is correct regarding rear axles of a vehicle? I. The Banjo axle arrangement is a central housing that contains the final drive and it is fitted with a tube on each side to carry the half axles and bearings. II. The main advantage of three-quarter floating rear axle over the half floating axle is that the major part of the load is taken by the axle and not by the axle casing. III. A full floating rear axle is not supported by bearing at either end, is very strong and used for heavy duty vehicles.

    1. Only II
    2. I and II
    3. Only III
    4. II and III
    Show answer

    Answer (TSPSC's preliminary key): (3) Only III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  40. Q40 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Which of the following is correct regarding causes of axle failure of a vehicle? I. Lubricant is not maintained at the required level. II. The vehicle is over loaded. III. Using of lubricant of correct grade.

    1. Only I
    2. II and III
    3. I and II
    4. Only III
    Show answer

    Answer (TSPSC's preliminary key): (3) I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  41. Q41 · Automobile Chassis & Transmission · Clutch & Gearbox

    Match the following symptoms with their causes for troubleshooting of gear box.

    SymptomsCauses
    I. Oil leaks1. Excessive wear on gear shift control
    II. Gear jumps out2. Defective synchronizer
    III. Gears clash while they are shifted3. Broken gaskets
    4. Heavy heat contact on the ring gear
    1. I-1, II-2, III-3
    2. I-3, II-1, III-2
    3. I-2, II-1, III-4
    4. I-4, II-3, III-1
    Show answer

    Answer (TSPSC's preliminary key): (2) I-3, II-1, III-2

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  42. Q42 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Which of the following is a correctly matched pair universal joint of a vehicle with their classification?

    1. Tracta type : Variable velocity joints
    2. Rzeppa type : Variable velocity joint
    3. Ball and Trunion type : Variable velocity joints
    4. Ring type : Constant velocity joint
    Show answer

    Answer (TSPSC's preliminary key): (3) Ball and Trunion type : Variable velocity joints

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  43. Q43 · Automobile Chassis & Transmission · Wheels & Tyres

    Which of the following is correctly matched pair regarding the tyres?

    1. Ply : The cross grooved tyre tread
    2. Carcass : An aunclar torridal shaped inflatable envelope made of an elastic material
    3. Ribs : The layer of rubber coated parallel cords
    4. Bead : Part which is shaped to fit the rim and hold the tyre on it
    Show answer

    Answer (TSPSC's preliminary key): (4) Bead : Part which is shaped to fit the rim and hold the tyre on it

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  44. Q44 · Automobile Chassis & Transmission · Clutch & Gearbox

    Arrange the following position in decreasing order of power transmission based on the position of gear shift lever of a vehicle. I. Low position II. Reverse position III. Neutral position

    1. I, II, III
    2. II, I, III
    3. III, I, II
    4. III, II, I
    Show answer

    Answer (TSPSC's preliminary key): (1) I, II, III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  45. Q45 · Automobile Chassis & Transmission · Brakes

    Arrange the following in a correct order (first to last) for air brakes of a vehicle. I. The air pressure act on a diaphragm of brake chamber. II. Brake shoes expands outwards and hold the moving brake drums. III. The foot pedal is pressed down. IV. The diaphragm is pushed outward in the brake chamber causing movement of brake shoe operating cam.

    1. III, IV, I, II
    2. III, I, IV, II
    3. III, IV, II, I
    4. III, II, IV, I
    Show answer

    Answer (TSPSC's preliminary key): (2) III, I, IV, II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  46. Q46 · Automobile Chassis & Transmission · Clutch & Gearbox

    Arrange the following statements in correct order (first to last) regarding fluid coupling. I. The prime mover starts rotating. II. The oil is thrown outwards by centrifugal action by pump impeller. III. The oil then enters the impeller pump again. IV. The pump impeller starts rotating. V. The oil enters the turbine runner and exerts force on runner blades. VI. The torque increases results in rotation of turbine runner after overcoming inertia effects.

    1. I, V, II, IV, III, VI
    2. I, II, III, V, IV, VI
    3. I, IV, II, V, VI, III
    4. II, III, I, VI, IV, V
    Show answer

    Answer (TSPSC's preliminary key): (3) I, IV, II, V, VI, III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  47. Q47 · Motor Vehicles Act, Transport & Maintenance · Vehicle Maintenance & Testing

    Which of the following is correct for improving fuel economy of vehicle?

    1. Under inflated tyre consume less fuel
    2. Check and maintain low engine oil level
    3. Replace the brake fluid to avoid extra fuel consumption
    4. Keep a constant speed as road traffic situation permit
    Show answer

    Answer (TSPSC's preliminary key): (4) Keep a constant speed as road traffic situation permit

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  48. Q48 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is a standard operating condition for an automotive engine as per Indian Standard Institute?

    1. Intake air temperature is 25°C
    2. Water vapour pressure of 150 mm of Hg of mercury, corresponding to a relative humidity of 40 percent at 25°C
    3. Mean barometric pressure of 736 mm Hg corresponding to an altitude of 300 metres above mean sea level
    4. Intake temperature is 45°C
    Show answer

    Answer (TSPSC's preliminary key): (3) Mean barometric pressure of 736 mm Hg corresponding to an altitude of 300 metres above mean sea level

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  49. Q49 · Motor Vehicles Act, Transport & Maintenance · Vehicle Maintenance & Testing

    Which of the following information is conveyed by the lubrication chart of the vehicle?

    1. The type of lubricant needed for a particular point
    2. The battery acid level
    3. Carbon deposition on sparkplug
    4. Type of engine oil needed
    Show answer

    Answer (TSPSC's preliminary key): (1) The type of lubricant needed for a particular point

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  50. Q50 · Automotive Electrical & Electronics · Batteries & Charging

    Which of the following is a part of charging system of the automotive electrical system?

    1. Horns
    2. Alternator
    3. Electronic ignition systems
    4. Lighting
    Show answer

    Answer (TSPSC's preliminary key): (2) Alternator

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  51. Q51 · Automotive Electrical & Electronics · Batteries & Charging

    Which of the following test is conducted to ascertain the conditions of a battery of an automobile?

    1. Hydrometer testing
    2. Morse testing
    3. Motoring test
    4. Static brake testing
    Show answer

    Answer (TSPSC's preliminary key): (1) Hydrometer testing

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  52. Q52 · Automotive Electrical & Electronics · Starting & Ignition

    Which of the following is a merit of transistorized coil ignition systems over conventional ignition system of a vehicle?

    1. Better working of contact breaker at high speeds
    2. Less costly
    3. Increased service life of spark plug
    4. Improves life of contact breaker
    Show answer

    Answer (TSPSC's preliminary key): (3) Increased service life of spark plug

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  53. Q53 · Automotive Electrical & Electronics · Lighting, Instruments & Wiring

    According to Lucas, what is the colour of wiring cables for dynamo circuit of a car?

    1. Red
    2. Black
    3. Green
    4. Yellow
    Show answer

    Answer (TSPSC's preliminary key): (4) Yellow

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  54. Q54 · Automotive Electrical & Electronics · Lighting, Instruments & Wiring

    The lights which indicate the direction the vehicle is about to turn are ______.

    1. side lights
    2. trafficators
    3. tail light
    4. reverse light
    Show answer

    Answer (TSPSC's preliminary key): (2) trafficators

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  55. Q55 · Thermodynamics & Heat Transfer · Refrigeration & Air Conditioning

    Which of the following is correct regarding hot water liquid heater in an automobile?

    1. It consists of a combustion chamber and re-ignitor.
    2. Outside air made to flow through the passage between the covering and exhaust manifold and air then circulated inside the car.
    3. The heat from the coolant circulating inside the engine is converted into hot air.
    4. A mixture of air and fuel is drawn from carburetor and burns inside the combustion chamber.
    Show answer

    Answer (TSPSC's preliminary key): (3) The heat from the coolant circulating inside the engine is converted into hot air.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  56. Q56 · Motor Vehicles Act, Transport & Maintenance · Vehicle Maintenance & Testing

    Which of the following is correct regarding the preventive maintenance of a car?

    1. The horsepower improves more than the rated level
    2. Fuel mileage is increased dramatically
    3. There is no replacement of parts
    4. It leads to sharp drop in performance of vehicle
    Show answer

    Answer (TSPSC's preliminary key): (2) Fuel mileage is increased dramatically

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  57. Q57 · Motor Vehicles Act, Transport & Maintenance · Vehicle Maintenance & Testing

    Which of the following is a correct about preventive maintenance of piston and piston rings of a car? I. Piston rings are to be checked for tension and scratches. II The carbon is removed and piston is cleaned using caustic cleaning solution and wire brush.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (1) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  58. Q58 · Automotive Electrical & Electronics · Starting & Ignition

    Which of the following is correct about vacuum spark advance mechanism of an engine? I. It contains a spring loaded diaphragm which is connected with the distributor by means of a link and damp. II. When distributor body is rotated opposite to the rotation of the rotor ignition is advanced.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  59. Q59 · Automotive Electrical & Electronics · Starting & Ignition

    Which of the following statements is correct regarding starting motor of an automobile? I. Bendix drive is known as overrunning clutch drive. II. The pole shoes hold the field coils and become magnetized when current flows through the coil. III. The purpose of the solenoid switch is to shift the drive pinion magnetically into mesh with the flywheel to complete the circuit. IV. If the starter works but does not crank the engine then the solenoid switch may be defective.

    1. I, II
    2. I, II and III
    3. II, IV
    4. II, III
    Show answer

    Answer (TSPSC's preliminary key): (4) II, III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  60. Q60 · Automotive Electrical & Electronics · Batteries & Charging

    Match the following.

    FunctionComponents
    I. Convert mechanical energy from engine into electrical energy1. Regulator
    II. Control the amount of electrical energy produced2. Relay
    III. Converts electrical energy into mechanical energy3. Dynamo
    4. Starting motor
    1. I-3, II-1, III-4
    2. I-1, II-4, III-3
    3. I-2, II-1, III-4
    4. I-1, II-2, III-3
    Show answer

    Answer (TSPSC's preliminary key): (1) I-3, II-1, III-4

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  61. Q61 · Automotive Electrical & Electronics · Starting & Ignition

    Which of the following is a correctly matched pair regarding troubles in spark plug and ignition system with their cause? I. Engine misfires on one cylinder : Detached high tension cable II. External insulator broken : Defective ignition coil III. Engine gets unduly hot : Loose contact screws

    1. Only III
    2. Only I and II
    3. Only I
    4. Only I and III
    Show answer

    Answer (TSPSC's preliminary key): (3) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  62. Q62 · Automotive Electrical & Electronics · Lighting, Instruments & Wiring

    Arrange the following in decreasing order of total value of resistance. I. V = 200 V, I = 10 Amp II. R₁ = 5.5 Ω, R₂ = 10 Ω and R₃ = 6.5 Ω arranged in series circuit III. R₁ = 5 Ω, R₂ = 12 Ω and R₃ = 6 Ω arranged in parallel circuit

    1. I, II, III
    2. I, III, II
    3. II, III, I
    4. II, I, III
    Show answer

    Answer (TSPSC's preliminary key): (4) II, I, III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  63. Q63 · Motor Vehicles Act, Transport & Maintenance · Vehicle Maintenance & Testing

    Arrange the following in a correct order (first to last) for washing the car. I. Wash all body panels. II. Lift the car on a car lift. III. Dry the car using a clean chamois. IV. Complete the washing with a sponge using running water. V. Wash the bottom of the car wheels included. VI. Rub a polishing compound of good commercial grade with a cloth.

    1. II, V, VI, III, I, IV
    2. I, IV, III, VI, V, II
    3. III, II, V, IV, I, VI
    4. II, V, I, IV, III, VI
    Show answer

    Answer (TSPSC's preliminary key): (4) II, V, I, IV, III, VI

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  64. Q64 · Engineering Mechanics & Machine Design · Engineering Mechanics

    What is the value of TAB and TAC in the given diagram? (where sin165° = 0.26)

    Figure for question 64
    1. TAB = 4950 N, TAC = 3005 N
    2. TAC = 1810 N, TAB = 4950 N
    3. TAB = 1810 N, TAB = 3500 N
    4. TAB = 3500 N, TAC = 1810 N
    Show answer

    Answer (TSPSC's preliminary key): (2) TAC = 1810 N, TAB = 4950 N

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  65. Q65 · Materials, Manufacturing & Metrology · Metrology & Measurement

    The prefix used to show multiplying factor of 10⁻¹² is ______.

    1. tera
    2. nano
    3. pico
    4. fermi
    Show answer

    Answer (TSPSC's preliminary key): (3) pico

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  66. Q66 · Engineering Mechanics & Machine Design · Engineering Mechanics

    What is the total load acting on the beam AB?

    Figure for question 66
    1. 14400 N
    2. 7200 N
    3. 720 N
    4. 1440 N
    Show answer

    Answer (TSPSC's preliminary key): (3) 720 N

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  67. Q67 · Engineering Mechanics & Machine Design · Engineering Mechanics

    The ratio of the limiting force of friction (F) to the normal reaction (R) between two bodies is called ______.

    1. Coefficient of repose
    2. Angle of repose
    3. Frictional power
    4. Coefficient of friction
    Show answer

    Answer (TSPSC's preliminary key): (4) Coefficient of friction

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  68. Q68 · Engineering Mechanics & Machine Design · Strength of Materials

    The change in length (elongation) of bar due to self-weight is given by ______. (P = Load, ρ = density, E = Young’s Modulus, d₁ and d₂ are diameters)

    1. ρgl/(3E)
    2. ρgl²/(2E)
    3. 4PL/(πd₁d₂E)
    4. ρgL/(2πd₁d₂G)
    Show answer

    Answer (TSPSC's preliminary key): (2) ρgl²/(2E)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  69. Q69 · Engineering Mechanics & Machine Design · Strength of Materials

    Which of the following is a correct relation between the material properties? (where (1/m) is poission ratio, K is bulk modulus, E is Young’s modulus)

    1. K = mE/(3(m − 2))
    2. K = E/(2(1/m + 1))
    3. K = 2mE/(m + 2)
    4. K = mE/(2m + 1)
    Show answer

    Answer (TSPSC's preliminary key): (1) K = mE/(3(m − 2))

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  70. Q70 · Engineering Mechanics & Machine Design · Strength of Materials

    Which of the following is a possible shear force diagram for an inclined beam under uniformly distributed load and a point load as shown in a diagram?

    Figure for question 70
    1. Figure 1
    2. Figure 2
    3. Figure 3
    4. Figure 4
    Show answer

    Answer (TSPSC's preliminary key): (3) Figure 3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  71. Q71 · Engineering Mechanics & Machine Design · Strength of Materials

    The maximum deflection for a simply supported beam with a uniformly distributed load is given by ______. (Where w is weight per unit length)

    1. wl³/(584El)
    2. 5wl⁴/(384El)
    3. wl³/(16El)
    4. wl⁴/(48El)
    Show answer

    Answer (TSPSC's preliminary key): (2) 5wl⁴/(384El)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  72. Q72 · Engineering Mechanics & Machine Design · Strength of Materials

    Which of the following is a bending moment diagram for a cantilever beam with a uniformly distributed load?

    Figure for question 72
    1. Figure 1
    2. Figure 2
    3. Figure 3
    4. Figure 4
    Show answer

    Answer (TSPSC's preliminary key): (4) Figure 4

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  73. Q73 · Engineering Mechanics & Machine Design · Strength of Materials

    The ratio of lateral strain to linear strain of a body is called ______.

    1. Resilience
    2. Deflection
    3. Poisson's ratio
    4. Young’s modulus
    Show answer

    Answer (TSPSC's preliminary key): (3) Poisson's ratio

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  74. Q74 · Engineering Mechanics & Machine Design · Strength of Materials

    Which of the following is correct about strain in a body? I. Shear strain is defined as the ratio between change in volume and original volume of the body. II. The ratio between the compressing stress and compressive strain is called modulus of elasticity.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  75. Q75 · Engineering Mechanics & Machine Design · Strength of Materials

    Which of the following is correct regarding load? I. For a bar with different section subjected to axial load P, the resultant deformation will be summation of change of length of every section. II. For the above diagram the value of P₁ is 52 N.

    Figure for question 75
    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (1) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  76. Q76 · Engineering Mechanics & Machine Design · Strength of Materials

    A 1 m long rod is fixed at both ends. What is the temperature through which rod can be heated to NOT exceed the thermal stress of 90 MPa? The value of α is 2 × 10⁻⁵ K⁻¹ and E is 90 GPa.

    1. 90 K
    2. 180 K
    3. 50 K
    4. 100 K
    Show answer

    Answer (TSPSC's preliminary key): (3) 50 K

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  77. Q77 · Engineering Mechanics & Machine Design · Strength of Materials

    Which of the following is correct regarding thermal stress? I. If the supports yield by an amount Δ, the change in length will be summation of l α T and Δ. II. The stress of the supports yield by an amount Δ is (αt − Δ/l) E. (where l = length of the original body, α = coefficient of thermal expansion)

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  78. Q78 · Engineering Mechanics & Machine Design · Strength of Materials

    Which of the following is correct regarding elasticity of a body? I. In elasticity, the body regains its shape after force is removed. II. The resistance force remains even after load is removed. III. The body can regain its original shape after load removed upto elastic limit.

    1. Only I
    2. II and III only
    3. I and III only
    4. I and II only
    Show answer

    Answer (TSPSC's preliminary key): (3) I and III only

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  79. Q79 · Engineering Mechanics & Machine Design · Strength of Materials

    Which of the following is correct regarding shearing force, bending moment and loading condition on the beam? I. A point load at a section on the beam will cause sudden change in shear force. II. A point load at a section on the beam will results in sudden change in bending moment. III. When there is no load between two point, then shear force does not change.

    1. Only I
    2. II and III only
    3. I and III only
    4. II only
    Show answer

    Answer (TSPSC's preliminary key): (3) I and III only

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  80. Q80 · Engineering Mechanics & Machine Design · Strength of Materials

    Match the following bending moment diagram with the conditions.

    Figure for question 80
    1. I-1, II-2, III-3, IV-4
    2. I-2, II-1, III-3, IV-4
    3. I-2, II-3, III-4, IV-1
    4. I-1, II-4, III-2, IV-3
    Show answer

    Answer (TSPSC's preliminary key): (4) I-1, II-4, III-2, IV-3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  81. Q81 · Engineering Mechanics & Machine Design · Strength of Materials

    Which of the following is a correctly matched pair regarding section modulus of different section?

    1. Hollow circular section : Z = (π/32)(D⁴ − d⁴)/(D/2)
    2. Solid circular section : Z = (π/32)d³
    3. Solid semi-circular section : Z = (3π/64)d³
    4. Hollow circular section : Z = (π/14)(D⁴ − d⁴)
    Show answer

    Answer (TSPSC's preliminary key): (2) Solid circular section : Z = (π/32)d³

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  82. Q82 · Engineering Mechanics & Machine Design · Strength of Materials

    Arrange the following in the increasing order of maximum bending moment for the given loading condition.

    Figure for question 82
    1. I, II, III
    2. II, III, I
    3. III, II, I
    4. III, I, II
    Show answer

    Answer (TSPSC's preliminary key): (4) III, I, II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  83. Q83 · Engineering Mechanics & Machine Design · Engineering Mechanics

    Arrange the following in a decreasing order of the moment of inertia of the given geometric shapes. I. Circle II. Quarter circle III. Semi-circle

    1. I, II, III
    2. II, III, I
    3. I, III, II
    4. II, I, III
    Show answer

    Answer (TSPSC's preliminary key): (3) I, III, II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  84. Q84 · Engineering Mechanics & Machine Design · Engineering Mechanics

    Arrange the following steps of analysis of machines in a correct order (first to last). I. Dismember the machine and draw a free body diagram of each member. II. Draw a free body diagram of the whole machine. III. Equilibrium equations can be written and solved. IV. Consider multiforce member and show all the forces acting on the member. V. Finally check your solution.

    1. I, III, IV, II, V
    2. II, I, III, IV, V
    3. II, I, IV, III, V
    4. IV, I, II, III, V
    Show answer

    Answer (TSPSC's preliminary key): (3) II, I, IV, III, V

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  85. Q85 · Materials, Manufacturing & Metrology · Metrology & Measurement

    For the limit system, what is the difference between the basic dimensions of the mating parts is called?

    1. Allowance
    2. Fundamental deviation
    3. Tolerance
    4. Mean deviation
    Show answer

    Answer (TSPSC's preliminary key): (1) Allowance

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  86. Q86 · Engineering Mechanics & Machine Design · Machine Design

    The ratio of maximum stress to the working stress of a material is called ______.

    1. Strain
    2. Poisson’s ratio
    3. Factor of safety
    4. Young modulus
    Show answer

    Answer (TSPSC's preliminary key): (3) Factor of safety

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  87. Q87 · Engineering Mechanics & Machine Design · Machine Design

    The stresses which vary from one value of tensile to same value of compressive or vice versa of the beam are known as ______.

    1. repeated stress
    2. bending stress
    3. fluctuating stress
    4. completely reversed stress
    Show answer

    Answer (TSPSC's preliminary key): (4) completely reversed stress

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  88. Q88 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    What does the weld symbol ‘—’ represents according to IS : 813 – 1961?

    1. Field weld
    2. Chipping finish
    3. Flush contour
    4. Flash welding
    Show answer

    Answer (TSPSC's preliminary key): (3) Flush contour

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  89. Q89 · Engineering Mechanics & Machine Design · Machine Design

    The surface joining the crest and root of the screw threads is called ______.

    1. pitch
    2. slope
    3. lead
    4. flank
    Show answer

    Answer (TSPSC's preliminary key): (4) flank

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  90. Q90 · Engineering Mechanics & Machine Design · Engineering Mechanics

    The ratio of load lifted to the effort applied for a lever is called ______.

    1. Notch sensitivity
    2. Moment
    3. Mechanical advantage
    4. Mechanical efficiency
    Show answer

    Answer (TSPSC's preliminary key): (3) Mechanical advantage

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  91. Q91 · Engineering Mechanics & Machine Design · Machine Design

    The perpendicular distance between the centre lines of the successive rows in riveted joints is called ______.

    1. pitch
    2. marginal pitch
    3. back pitch
    4. diagonal pitch
    Show answer

    Answer (TSPSC's preliminary key): (3) back pitch

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  92. Q92 · Engineering Mechanics & Machine Design · Machine Design

    Which one of the following is related to the crushing of the rivets? (where, α = coefficient of thermal expansion, ΔT = change in temperature, σc = crushing stress, p = pitch of rivets, d = diameter of rivet hole, t = thickness of the plate and n = number rivets, Pc = crushing resistance)

    1. Pc = n.d.t.σc
    2. Pc = n(π/4).d². σc
    3. Pc = (p − d)t. σc
    4. Pc = α ΔT
    Show answer

    Answer (TSPSC's preliminary key): (1) Pc = n.d.t.σc

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  93. Q93 · Engineering Mechanics & Machine Design · Theory of Machines

    Which of the following gives the coefficient of fluctuation of speed of a flywheel? (where N₁ = Maximum speed during cycle and N₂ is minimum speed during the cycle)

    1. Cₛ = (N₁ + N₂)/(N₁ − N₂)
    2. Cₛ = (N₁ − N₂)/(2(N₁ + N₂))
    3. Cₛ = 2(N₁ − N₂)/(N₁ + N₂)
    4. Cₛ = 2(N₁ + N₂)/(N₁ − N₂)
    Show answer

    Answer (TSPSC's preliminary key): (3) Cₛ = 2(N₁ − N₂)/(N₁ + N₂)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  94. Q94 · Engineering Mechanics & Machine Design · Machine Design

    Which of the following is correct regarding leaf spring?

    1. It consists of a number of flat plates of varying lengths.
    2. In this spring, fluid behave as a compressive spring.
    3. This type of springs are helical in shape and used under compressive load only.
    4. It is made of a wire coiled in the form of a helix.
    Show answer

    Answer (TSPSC's preliminary key): (1) It consists of a number of flat plates of varying lengths.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  95. Q95 · Automobile Chassis & Transmission · Clutch & Gearbox

    Which of the following is correct regarding clutches? I. The material used as a friction surface of clutch should have low heat conductivity. II. The material used as a friction surface for clutches should have high and uniform coefficient of friction.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  96. Q96 · Engineering Mechanics & Machine Design · Machine Design

    Which of the following is the advantage of rolling contact bearings over sliding contact bearings? I. They have high resistance to shock loading. II. They have low starting and running friction except at very high speeds.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  97. Q97 · Engineering Mechanics & Machine Design · Theory of Machines

    Which of the following is the advantage of the involute gears? I. The centre distance for a pair of involute gear can be varied within limits without changing the velocity ratio. II. The interference does not occur at all in this type of gears.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (1) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  98. Q98 · Engineering Mechanics & Machine Design · Machine Design

    Which of the following is correct regarding springs? I. For the springs connected in series, the total deflection of the springs is summation of the deflection of each spring. II. For the springs connected in series, the combined stiffness of the spring is sum of the stiffness of each spring. III. For the springs connected in parallel, the total load acting on it is the sum of the loads acting on individual springs.

    1. I and II
    2. II and III
    3. I and III
    4. Only III
    Show answer

    Answer (TSPSC's preliminary key): (3) I and III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  99. Q99 · Engineering Mechanics & Machine Design · Machine Design

    Which of the following is correct regarding the sunk keys? I. A rectangular sunk key with a head at one end is called splines. II. A key attached as one member of a pair and which permits relative axial movement is known as woodruff key. III. Woodruff key’s advantage is it accommodates itself to any taper in the hub or boss of the mating piece.

    1. Only I
    2. II and III
    3. Only III
    4. I and III only
    Show answer

    Answer (TSPSC's preliminary key): (3) Only III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  100. Q100 · Engineering Mechanics & Machine Design · Machine Design

    Match the following method with the equation for combination of stresses. (where σv = variable stress, σm = mean stress, σu = ultimate stress, σe = endurance limit for reversed loading, Kf = fatigue stress concentration factor, F.S. = factor of safety, σy = yielding stress)

    Equation for combination of stressMethod
    I. 1/F.S. = (σm/σu)² F.S. + σv.Kf/σe1. Soderberg method
    II. 1/F.S. = σm/σu + σv.Kf/σe2. Gerber method
    III. 1/F.S. = σm/σy + σv.Kf/σe3. Goodman method
    1. I-1, II-3, III-2
    2. I-2, II-1, III-3
    3. I-3, II-2, III-1
    4. I-2, II-3, III-1
    Show answer

    Answer (TSPSC's preliminary key): (4) I-2, II-3, III-1

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  101. Q101 · Engineering Mechanics & Machine Design · Theory of Machines

    Which of the following is a correctly matched pair regarding the classification of gears based on the position of axes of shafts?

    1. Mitres : Intersecting and non-parallel
    2. Spur gear : Non-parallel and non-intersecting
    3. Helical gear : Intersecting and non-parallel
    4. Spiral gear : Parallel and non-intersecting
    Show answer

    Answer (TSPSC's preliminary key): (1) Mitres : Intersecting and non-parallel

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  102. Q102 · Engineering Mechanics & Machine Design · Strength of Materials

    Which one of the following is a correctly matched pair?

    SectionDistance from the neutral axis to the extreme fibre
    I. Triangleh/2
    II. Hollow rectangleh/2
    III. I-sectionh/3
    IV. Hollow circle(d − d₁)/2, (where d = outer diameter and d₁ = inner diameter)
    1. Only I
    2. Only II
    3. II and III
    4. Only IV
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  103. Q103 · Engineering Mechanics & Machine Design · Machine Design

    For a same tensile load, arrange the following in an increasing order of maximum stress, given the theoretical stress concentration factor is (1 + 2a/b). (where r = radius of the circle)

    Figure for question 103
    1. I, II, III
    2. II, I, III
    3. II, III, I
    4. I, III, II
    Show answer

    Answer (TSPSC's preliminary key): (3) II, III, I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  104. Q104 · Engineering Mechanics & Machine Design · Machine Design

    Arrange the following steps of procedure to solve design problem in a correct order (first to last). I. Synthesis II. Material selection III. Recognition of need IV. Detailed drawing V. Modification VI. Production VII. Analysis of forces VIII. Design of elements (size and stresses)

    1. III, I, VII, II, VIII, V, IV, VI
    2. II, III, V, VI, I, VIII, VII, IV
    3. VI, I, II, III, V, IV, VIII, VII
    4. IV, II, III, I, VII, VIII, V, VI
    Show answer

    Answer (TSPSC's preliminary key): (1) III, I, VII, II, VIII, V, IV, VI

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  105. Q105 · Engineering Mechanics & Machine Design · Machine Design

    Arrange the following steps in a correct order (first to last) of design procedure for journal bearing. I. Determine the bearing length by choosing ratio of l/d. II. Check the bearing pressure for a probable satisfactory value. III. Determine the heat generated. IV. Determine the operating value of ZN/p for the assumed bearing temperature and check this value. V. Determine the thermal equilibrium to see that the heat dissipated at least equal to heat generated. VI. Determine the coefficient of friction. VII. In case the heat generated is more than the heat dissipated than bearing is artificially cooled by water.

    1. I, II, IV, VI, III, V, VII
    2. II, I, III, V, VI, IV, VII
    3. I, II, VII, IV, VI, V, III
    4. III, V, VI, II, I, IV, VII
    Show answer

    Answer (TSPSC's preliminary key): (1) I, II, IV, VI, III, V, VII

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  106. Q106 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Which of the following is a finishing process of manufacturing?

    1. Soldering
    2. Extrusion
    3. Burnishing
    4. Milling
    Show answer

    Answer (TSPSC's preliminary key): (3) Burnishing

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  107. Q107 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Which of the following is a permanent mould casting process?

    1. Investment casting process
    2. Die casting
    3. Sand casting
    4. Lost foam casting
    Show answer

    Answer (TSPSC's preliminary key): (2) Die casting

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  108. Q108 · Materials, Manufacturing & Metrology · Engineering Materials

    Nylon is a ______.

    1. thermoplastic
    2. resin
    3. thermoset
    4. elastomer
    Show answer

    Answer (TSPSC's preliminary key): (1) thermoplastic

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  109. Q109 · Materials, Manufacturing & Metrology · Engineering Materials

    The property which allows material to undergo plastic deformation under tensile load before fracture is ______.

    1. brittleness
    2. ductility
    3. fatigue
    4. resilience
    Show answer

    Answer (TSPSC's preliminary key): (2) ductility

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  110. Q110 · Materials, Manufacturing & Metrology · Engineering Materials

    Which of the following is a test used to measure hardness of the material?

    1. Disk test
    2. Izod test
    3. Charpy test
    4. Vickers test
    Show answer

    Answer (TSPSC's preliminary key): (4) Vickers test

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  111. Q111 · Materials, Manufacturing & Metrology · Engineering Materials

    The permanent elongation of a component under a static load maintained for a long period of time is called ______.

    1. Plasticity
    2. Creep
    3. Fatigue fracture
    4. Residual stress
    Show answer

    Answer (TSPSC's preliminary key): (2) Creep

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  112. Q112 · Materials, Manufacturing & Metrology · Engineering Materials

    When white cast iron is annealed in an atmosphere of carbon monoxide and carbon dioxide, at temperature between 800°C and 900°C for several hours depending on size, we obtain ______.

    1. compacted graphite iron
    2. nodular iron
    3. gray cast iron
    4. malleable iron
    Show answer

    Answer (TSPSC's preliminary key): (4) malleable iron

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  113. Q113 · Materials, Manufacturing & Metrology · Engineering Materials

    The heating process by which hardness is reduced and toughness is improved is called ______.

    1. quenching
    2. cyaniding
    3. tempering
    4. carburizing
    Show answer

    Answer (TSPSC's preliminary key): (3) tempering

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  114. Q114 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    The machining process of making a hole by removing a disk shaped piece from a flat plate is called ______.

    1. trepanning
    2. gun drilling
    3. boring
    4. tapping
    Show answer

    Answer (TSPSC's preliminary key): (1) trepanning

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  115. Q115 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Which of the following is a correct relation of material removal rate for milling? (l = length of cut, w = width of the cut, d = depth of cut, t = cutting time, f = feed per tooth, v = feed rate)

    1. MRR = (l × w)/(d × t)
    2. MRR = (f × d × t)/l
    3. MRR = (w × d)/v
    4. MRR = (l × w × d)/t
    Show answer

    Answer (TSPSC's preliminary key): (4) MRR = (l × w × d)/t

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  116. Q116 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    The phenomenon of wandering of arc that occurs in DC welding is called ______.

    1. Arc blow
    2. Spattering
    3. Underfilling
    4. Lamellar tears
    Show answer

    Answer (TSPSC's preliminary key): (1) Arc blow

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  117. Q117 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Which of the following is correct regarding the process of reaming? I. Reaming is an operation used to achieve a high grade of surface finish on a hole. II. The tool used in reaming operation has multiple cutting edges.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  118. Q118 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Which of the following is correct regarding the lathe operations? I. Process of reducing the diameter of a workpiece over a very narrow surface is called knurling. II. Knurling is done at the slowest speed available in a lathe.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  119. Q119 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Which of the following is correct about broaching? I. It is a process of machining a surface with a special multipoint tool. II. Gears cannot be manufactured using a broaching process.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (1) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  120. Q120 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Which of the following is correct regarding forging? I. Upsetting is a process of increasing cross sectional dimensions when forging. II. Process of cutting large holes of various shapes by using a chisel over a hole in the sewage block is called setting down. III. One of the advantages of open die forging is, it can be employed for long run production.

    1. Only I
    2. I and II only
    3. II and III only
    4. Only III
    Show answer

    Answer (TSPSC's preliminary key): (1) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  121. Q121 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Which of the following is correct regarding electron beam machining? I. It can be used on all materials. II. Material removal rate is low and vacuum is needed for operation. III. The voltage required for electron beam machining is 1150 kV.

    1. I and III only
    2. I and II only
    3. II and III only
    4. Only III
    Show answer

    Answer (TSPSC's preliminary key): (2) I and II only

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  122. Q122 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Which of the following is correct regarding advantages of cold working? I. Ductility of metal is improved. II. Minimum contamination during cold working compare to hot working. III. Good surface finish and better dimensional accuracy than hot working.

    1. Only I
    2. Only II
    3. II and III only
    4. I and II only
    Show answer

    Answer (TSPSC's preliminary key): (3) II and III only

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  123. Q123 · Materials, Manufacturing & Metrology · Engineering Materials

    Match the following elements with its effect on the steel.

    ElementsEffect on the steel
    I. Calcium1. Improves hardenability
    II. Boron2. Improves resistance to atmospheric corrosion
    III. Lead3. Improves toughness and formability
    IV. Copper4. Improves machinability
    1. I-3, II-4, III-1, IV-2
    2. I-2, II-1, III-4, IV-3
    3. I-3, II-1, III-4, IV-2
    4. I-2, II-4, III-1, IV-3
    Show answer

    Answer (TSPSC's preliminary key): (3) I-3, II-1, III-4, IV-2

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  124. Q124 · Materials, Manufacturing & Metrology · Engineering Materials

    Which one of the following is a correctly matched pair?

    1. Grey cast iron : Graphite exists largely in form of flakes
    2. White cast iron : Graphite in a spherical form
    3. Ductile iron : Graphite in form of short, thick interconnected flakes
    4. Compacted graphite iron : Do not have any carbon flakes
    Show answer

    Answer (TSPSC's preliminary key): (1) Grey cast iron : Graphite exists largely in form of flakes

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  125. Q125 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Arrange the following brazing alloys in order of their increasing melting point. I. Copper = 50 percent, Zinc = 50 percent II. Copper = 70 percent, Zinc = 30 percent III. Copper = 60 percent, Zinc = 40 percent

    1. I, II, III
    2. II, III, I
    3. III, II, I
    4. I, III, II
    Show answer

    Answer (TSPSC's preliminary key): (4) I, III, II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  126. Q126 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Arrange the following three region in decreasing order of percentage of heat generated during metal cutting. I. The shear zone II. The chip tool interface region III. The tool-work interface region

    1. III, II, I
    2. I, II, III
    3. II, III, I
    4. II, I, III
    Show answer

    Answer (TSPSC's preliminary key): (2) I, II, III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  127. Q127 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Arrange the following steps in a correct order (first to last) regarding thermit welding. I. After cutting, pouring and heating gates and risers a flame is directed into heating oven to drain out wax. II. Molten iron run into the mould which fuses with part to be welded. III. Wax pattern of desired size and shape is prepared around joint. IV. The thermit mixture packed in the crucible of conical shape formed from sheet iron casting lined with heat resisting cement is ignited.

    1. I, II, IV, III
    2. III, I, IV, II
    3. II, IV, III, I
    4. IV, III, II, I
    Show answer

    Answer (TSPSC's preliminary key): (2) III, I, IV, II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  128. Q128 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Arrange the following steps in a correct order (first to last) of greens and mouldings. I. Making the mould II. Closing and weighing III. Core setting IV. Preparation of the pattern

    1. II, I, III, IV
    2. IV, I, III, II
    3. III, II, IV, I
    4. II, IV, I, III
    Show answer

    Answer (TSPSC's preliminary key): (2) IV, I, III, II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  129. Q129 · Automobile Chassis & Transmission · Chassis & Body

    The actual average rate of coverage by the farm machine, based upon total field time is called ______.

    1. effective operating time
    2. theoretical field capacity
    3. field efficiency
    4. effective field capacity
    Show answer

    Answer (TSPSC's preliminary key): (4) effective field capacity

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  130. Q130 · Automobile Chassis & Transmission · Chassis & Body

    An assemblage of one or more winding drums mounted on a frame of a crane is called ______.

    1. Main clutch
    2. Winch
    3. Boom
    4. Flange
    Show answer

    Answer (TSPSC's preliminary key): (2) Winch

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  131. Q131 · Fluid Mechanics & Hydraulics · Fluid Mechanics

    A fluid in which shear stress is more than the yield value and shear stress is proportional to the rate of shear strain is called ______.

    1. Newtonian fluid
    2. Ideal fluid
    3. Ideal plastic fluid
    4. Real fluid
    Show answer

    Answer (TSPSC's preliminary key): (3) Ideal plastic fluid

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  132. Q132 · Fluid Mechanics & Hydraulics · Fluid Mechanics

    What is the ratio of dynamic viscosity to the density of the fluid?

    1. Mass
    2. Kinematic viscosity
    3. Specific gravity
    4. Specific volume
    Show answer

    Answer (TSPSC's preliminary key): (2) Kinematic viscosity

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  133. Q133 · Fluid Mechanics & Hydraulics · Hydraulic Machines & Pneumatics

    The ratio of weight lifted to the force applied on the plunger of a hydraulic press is called ______.

    1. Volumetric efficiency
    2. Mechanical advantage
    3. Rankine efficiency
    4. Effort
    Show answer

    Answer (TSPSC's preliminary key): (2) Mechanical advantage

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  134. Q134 · Fluid Mechanics & Hydraulics · Hydraulic Machines & Pneumatics

    The ratio of power given by water to the runner of a turbine to the power supplied by the water at the inlet of the turbine is called ______.

    1. Overall efficiency
    2. Mechanical efficiency
    3. Hydraulic efficiency
    4. Volumetric efficiency
    Show answer

    Answer (TSPSC's preliminary key): (3) Hydraulic efficiency

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  135. Q135 · Fluid Mechanics & Hydraulics · Hydraulic Machines & Pneumatics

    The axial flow reaction turbine which vanes on the hub are adjustable is called ______.

    1. Propeller turbine
    2. Francis turbine
    3. Pelton turbine
    4. Kaplan turbine
    Show answer

    Answer (TSPSC's preliminary key): (4) Kaplan turbine

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  136. Q136 · Fluid Mechanics & Hydraulics · Fluid Mechanics

    The flow in which the velocity at any given time changes with respect to space are called ______.

    1. Non-uniform flow
    2. Steady flow
    3. Uniform flow
    4. Unsteady flow
    Show answer

    Answer (TSPSC's preliminary key): (1) Non-uniform flow

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  137. Q137 · Automobile Chassis & Transmission · Chassis & Body

    Which of the following vehicle have rotating beam attached to a vertical mast and supporting a hoist?

    1. Bulldozer
    2. Fork lift truck
    3. Loaders
    4. Jib Crane
    Show answer

    Answer (TSPSC's preliminary key): (4) Jib Crane

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  138. Q138 · Automobile Chassis & Transmission · Chassis & Body

    Which of the following vehicle designed for transporting large quantities of bulk material like gravel over short distance?

    1. Fork lift truck
    2. Loaders
    3. Dumpers
    4. Bulldozer
    Show answer

    Answer (TSPSC's preliminary key): (3) Dumpers

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  139. Q139 · Fluid Mechanics & Hydraulics · Hydraulic Machines & Pneumatics

    Which of the following is correct regarding the Francis turbine? I. It is an inward flow reaction turbine having radial discharge at outlet. II. The work done by water on the runner per second is ρQ(Vw₁u₁). (where Q is discharge, Vw₁ = Whirl velocity at inlet, u₁ is blade velocity of wheel at inlet, ρ = density of fluid)

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  140. Q140 · Fluid Mechanics & Hydraulics · Fluid Mechanics

    Which of the following is correct regarding the surface tension? I. The pressure intensity of soap bubble is twice of a liquid droplet for same diameter and surface tension. II. Surface tension is a shear force acting on the surface of a liquid.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (1) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  141. Q141 · Fluid Mechanics & Hydraulics · Hydraulic Machines & Pneumatics

    Match the following turbines with their classification based on the direction of flow through runner.

    TurbineDirection of flow
    I. Pelton1. Axial flow reaction turbine
    II. Francis2. Tangential flow turbine
    III. Kaplan3. Inward flow reaction turbine
    1. I-1, II-2, III-3
    2. I-3, II-1, III-2
    3. I-3, II-2, III-1
    4. I-2, II-3, III-1
    Show answer

    Answer (TSPSC's preliminary key): (4) I-2, II-3, III-1

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  142. Q142 · Fluid Mechanics & Hydraulics · Fluid Mechanics

    Arrange the following in an increasing order of shear stress. I. Shear stress of oil with oil viscosity 12 poise, velocity of 2.5 m/s and clearance of 1.25 cm. II. Shear stress of oil having dynamic viscosity 0.1 Ns/m², clearance of 2 mm and velocity 2500 mm/s⁻¹. III. Shear stress of oil on an inclined plane having viscosity 2 poise, velocity 1.5 m/s and clearance of 3 cm.

    1. II, III, I
    2. I, II, III
    3. III, I, II
    4. III, II, I
    Show answer

    Answer (TSPSC's preliminary key): (4) III, II, I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  143. Q143 · Fluid Mechanics & Hydraulics · Fluid Mechanics

    Which of the following is correct about flow of fluids through pipes? I. Hydraulic gradient line gives the sum of pressure head and kinetic head. II. Total energy line gives the sum of pressure head, kinetic head and datum head. III. The Chezy’s formula for loss of head due to friction in pipes is h_f = 4.f.L.V²/(d2g) (where f = co-efficient of friction, L = length of pipe, V = mean velocity of flow, d = diameter of pipe)

    1. I and II
    2. Only II
    3. II and III
    4. I and III
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  144. Q144 · Fluid Mechanics & Hydraulics · Hydraulic Machines & Pneumatics

    Which of the following is correctly matched?

    Types of turbineSpecific speed in MKS units
    I. Francis turbine300 to 600
    II. Pelton wheel with single jet10 to 35
    III. Pelton wheel with two or more jets100 to 800
    IV. Kalpan Propeller turbine300 to 1000
    1. Only I and II
    2. Only I, II and III
    3. Only II and IV
    4. Only III and IV
    Show answer

    Answer (TSPSC's preliminary key): (3) Only II and IV

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  145. Q145 · Motor Vehicles Act, Transport & Maintenance · Motor Vehicles Act & Rules

    A registration code of a vehicle is given as: UP 26 B 9126. What does the value 26 represents?

    1. Series
    2. State code
    3. District or town code
    4. Village code
    Show answer

    Answer (TSPSC's preliminary key): (3) District or town code

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  146. Q146 · Motor Vehicles Act, Transport & Maintenance · Motor Vehicles Act & Rules

    Section 3 of The Motor Vehicles Act, 1988 deals with ______.

    1. Grant of learner’s licence
    2. Grant of driving licence
    3. Endorsement
    4. Necessity for driving licence
    Show answer

    Answer (TSPSC's preliminary key): (4) Necessity for driving licence

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  147. Q147 · Motor Vehicles Act, Transport & Maintenance · Transport Management

    Which of the following is correct regarding continuous flow production model? I. In this model, facility should be flexible to handle a wide variety of products. II. In this model a standard set of processes and sequence of processes can be adopted.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  148. Q148 · Motor Vehicles Act, Transport & Maintenance · Transport Management

    Which of the following is correct regarding principle for personnel management? I. People are to be dealt with as a complete individual. II. There should be fairness in dealing with the employees to win their confidence. III. All the employees doing the same type of work are not needed to pay the same.

    1. Only I
    2. I and II only
    3. II and III only
    4. III and I only
    Show answer

    Answer (TSPSC's preliminary key): (2) I and II only

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  149. Q149 · Motor Vehicles Act, Transport & Maintenance · Transport Management

    Which of the following is a correct pair regarding the types of communication in an organization? I. Downward communication : The transmission of feedback, orientation, complaints, suggestions for improvements etc. from lowest grade employee to top executive II. Horizontal communication : Transmission of information between persons having the same level of authority in the organization III. Upward communication : The transmission of instructions and information from top executive downwards to the lowest grade employee.

    1. Only I
    2. Only II
    3. II and III only
    4. I and III only
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  150. Q150 · Motor Vehicles Act, Transport & Maintenance · Road Safety

    Match the following.

    SignsSymbols
    I. Railway crossing (Guarded)1. Symbol 1
    II. Narrow bridge2. Symbol 2
    III. Cross roads3. Symbol 3
    IV. Steep hills4. Symbol 4
    Figure for question 150
    1. I-1, II-2, III-4, IV-3
    2. I-2, II-3, III-1, IV-4
    3. I-2, II-4, III-1, IV-3
    4. I-3, II-1, III-2, IV-4
    Show answer

    Answer (TSPSC's preliminary key): (2) I-2, II-3, III-1, IV-4

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.