Learn with Anil · TGPSC AMVI (Assistant Motor Vehicles Inspector) PYQsPractise online →Subscribe ₹149

TGPSC AMVI IC Engines, Fuels & Emissions previous year questions with answers

Every IC Engines, Fuels & Emissions question asked in the TGPSC AMVI (Assistant Motor Vehicles Inspector) papers on this site, grouped by topic. Answers come from TSPSC's preliminary key; each has a short explanation (free here for a sample, all of them in the practice app).

Practise IC Engines, Fuels & Emissions online

Engine Fundamentals & Cycles

  1. AMVI 2023 Paper 2 (Automobile) · Q3 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In context of I.C. engines, what is the ratio of shaft energy to the energy available at the piston is called?

    1. Brake thermal efficiency
    2. Indicated thermal efficiency
    3. Mechanical efficiency
    4. Volumetric efficiency
    Show answer

    Answer (TSPSC's preliminary key): (3) Mechanical efficiency

    Mechanical efficiency ηm = brake power / indicated power, i.e. the useful output at the shaft divided by the power developed by the gases on the piston; the difference is lost in friction and pumping. Brake thermal efficiency compares brake power with the fuel energy supplied, indicated thermal efficiency compares indicated power with the fuel energy, and volumetric efficiency compares the charge actually inducted with the swept volume.

  2. AMVI 2023 Paper 2 (Automobile) · Q4 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    For the I.C. engine, the ratio of total volume of the cylinder to clearance volume is called ______.

    1. clearance ratio
    2. efficiency
    3. expansion ratio
    4. compression ratio
    Show answer

    Answer (TSPSC's preliminary key): (4) compression ratio

    Compression ratio r = total cylinder volume / clearance volume = (Vs + Vc)/Vc, where Vs is the swept (stroke) volume and Vc the clearance volume left above the piston at TDC. Typical values are about 6–10 for petrol (SI) engines and 14–22 for diesel (CI) engines. The clearance ratio is Vc/Vs, and a higher compression ratio raises the air-standard efficiency.

  3. AMVI 2023 Paper 2 (Automobile) · Q5 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is an advantage of reciprocating internal combustion engines over external combustion engines?

    1. Starting torque is high
    2. Weight to power ratio is generally low
    3. Require more space
    4. Cheaper fuel can be used
    Show answer

    Answer (TSPSC's preliminary key): (2) Weight to power ratio is generally low

    Because the fuel burns inside the cylinder, an IC engine needs no boiler, condenser or separate furnace, so it is compact, with a low weight-to-power ratio and higher overall efficiency, which suits vehicles. External combustion engines such as steam engines give high starting torque and can burn cheaper fuels like coal or wood, but they need more space; these are not advantages of IC engines.

  4. AMVI 2023 Paper 2 (Automobile) · Q6 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is a function of Gudgeon pin in internal combustion engines?

    1. It acts as a face to receive gas pressure and transmits the thrust to connecting rod
    2. Provide a good sealing fit between the piston and cylinder
    3. It supports and allows the swivel of the connecting rod
    4. It reduces friction and takes care of the fluctuations of speed during a cycle
    Show answer

    Answer (TSPSC's preliminary key): (3) It supports and allows the swivel of the connecting rod

    The gudgeon (piston or wrist) pin joins the piston to the small end of the connecting rod and acts as a pivot, supporting the rod and allowing it to swivel as the crank turns. The piston crown receives the gas pressure, the piston rings give the seal between piston and cylinder, and the flywheel takes care of speed fluctuations during a cycle.

  5. AMVI 2023 Paper 2 (Automobile) · Q7 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    During which of the following stroke, the flywheel stores energy so that it can supply the energy during the idle strokes?

    1. Suction stroke
    2. Expansion stroke
    3. Compression stroke
    4. Exhaust stroke
    Show answer

    Answer (TSPSC's preliminary key): (2) Expansion stroke

    In a four-stroke engine only the expansion (power) stroke produces work. During this stroke the flywheel absorbs the surplus energy as kinetic energy, its speed rising slightly, and gives it back during the idle suction, compression and exhaust strokes, keeping the crankshaft speed nearly uniform. A multi-cylinder engine overlaps power strokes and so needs a lighter flywheel.

  6. AMVI 2023 Paper 2 (Automobile) · Q8 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    To allow the fresh charge to enter the cylinder, the inlet valve is opened in advance of the T.D.C position. The inlet valve is opened in advance by ______.

    1. 10° to 30°
    2. 50° to 60°
    3. 30° to 70°
    4. 0° to 10°
    Show answer

    Answer (TSPSC's preliminary key): (1) 10° to 30°

    In the actual valve timing of a four-stroke engine the inlet valve opens about 10°–30° of crank rotation before TDC, so that it is fully open when the suction stroke begins and the fresh charge can enter without restriction. It closes some degrees after BDC, using the inertia of the incoming charge to improve volumetric efficiency. The period when both valves are open near TDC is the valve overlap.

  7. AMVI 2023 Paper 2 (Automobile) · Q10 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In a two-stroke engine, the process of clearing the cylinder after the expansion stroke is called ______.

    1. expansion
    2. scavenging
    3. compressing
    4. knocking
    Show answer

    Answer (TSPSC's preliminary key): (2) scavenging

    Scavenging is the sweeping out of the burnt gases from the cylinder of a two-stroke engine by the fresh charge or air entering through the transfer ports at the end of the expansion stroke. Common methods are cross-flow, loop (reverse-flow) and uniflow scavenging. Knocking is abnormal combustion, while expansion and compression are the normal working processes.

  8. AMVI 2023 Paper 2 (Automobile) · Q11 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    What is the difference between indicated power and brake power of internal combustion engine?

    1. Total power
    2. Total available energy
    3. Total engine friction loss
    4. Total clearance
    Show answer

    Answer (TSPSC's preliminary key): (3) Total engine friction loss

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  9. AMVI 2023 Paper 2 (Automobile) · Q22 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    For same compression ratio and same heat input, which of the following order of efficiency is correct?

    1. η_duel > η_otto > η_diesel
    2. η_diesel > η_duel > η_otto
    3. η_duel > η_diesel > η_otto
    4. η_otto > η_duel > η_diesel
    Show answer

    Answer (TSPSC's preliminary key): (4) η_otto > η_duel > η_diesel

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  10. AMVI 2023 Paper 2 (Automobile) · Q24 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    For the four stroke otto engines, arrange the following in the correct order (first to last). I. The piston moves T.D.C. to B.D.C. and work is obtained after fuel is ignited. II. The piston moves B.D.C. to T.D.C. and compresses the air fuel mixture. III. The piston moves T.D.C. to B.D.C. and the inlet valve opens and air fuel mixture is sucked in. IV. The piston moves B.D.C. to T.D.C. and gases are made to escape through exhaust value.

    1. I, III, IV, II
    2. III, II, I, IV
    3. IV, II, I, III
    4. III, I, IV, II
    Show answer

    Answer (TSPSC's preliminary key): (2) III, II, I, IV

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  11. AMVI 2023 Paper 2 (Automobile) · Q48 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is a standard operating condition for an automotive engine as per Indian Standard Institute?

    1. Intake air temperature is 25°C
    2. Water vapour pressure of 150 mm of Hg of mercury, corresponding to a relative humidity of 40 percent at 25°C
    3. Mean barometric pressure of 736 mm Hg corresponding to an altitude of 300 metres above mean sea level
    4. Intake temperature is 45°C
    Show answer

    Answer (TSPSC's preliminary key): (3) Mean barometric pressure of 736 mm Hg corresponding to an altitude of 300 metres above mean sea level

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

Fuel Supply & Combustion

  1. AMVI 2023 Paper 2 (Automobile) · Q9 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which one of the following factors affect the ignition timing of an internal combustion engine?

    1. Type of fuel
    2. Flywheel
    3. Piston material
    4. Cylinder material
    Show answer

    Answer (TSPSC's preliminary key): (1) Type of fuel

    The spark must occur early enough for the flame to burn the charge near TDC, and the time needed depends on the fuel: its octane rating (knock resistance) and burning rate decide how much spark advance can be used. Engine speed, load and mixture strength also affect the timing, which is why distributors have centrifugal and vacuum advance. The flywheel and the piston or cylinder materials do not decide ignition timing.

  2. AMVI 2023 Paper 2 (Automobile) · Q14 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following is correct regarding the diesel engines? I. Diesel engines uses an injector. II. There is no pre-ignition in diesel engines.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  3. AMVI 2023 Paper 2 (Automobile) · Q17 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following is correct about the fuel injection system? I. It controls the rate of fuel injection. II. It filters the fuel. III. It controls the quantity of fuel to be injected.

    1. Only I and II
    2. Only II and III
    3. All I, II and III
    4. Only I and III
    Show answer

    Answer (TSPSC's preliminary key): (3) All I, II and III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  4. AMVI 2023 Paper 2 (Automobile) · Q18 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following statement is correct regarding the effects of the air fuel mixtures in SI engine? I. If the air fuel mixture is slightly richer, mean effective pressure reaches its maximum value. II. The rate of fuel consumption is lowest for rich air fuel mixtures. III. By decreasing the richness of air fuel mixture, the proportion of CO₂ will decrease while those of CO with certain traces of unburnt H₂ will increase.

    1. Only I
    2. Only II and III
    3. Only I and III
    4. Only II
    Show answer

    Answer (TSPSC's preliminary key): (1) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  5. AMVI 2023 Paper 2 (Automobile) · Q19 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Match the following statements in context of Spark Ignition engine.

    EffectCause
    I. Results in lowering of efficiency1. Running on the weakest air fuel mixture
    II. Results in high efficiency2. Running on the richest air fuel mixture
    III. Results in complete burning of the fuel3. During the cruising the air fuel mixture is approximately 16.5: 1 so that
    1. I-1, II-2, III-3
    2. I-2, II-1, III-3
    3. I-3, II-2, III-1
    4. I-2, II-3, III-1
    Show answer

    Answer (TSPSC's preliminary key): (2) I-2, II-1, III-3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  6. AMVI 2023 Paper 2 (Automobile) · Q25 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    For a simple or elementary carburettor, arrange the following in a correct order (first to last). I. The velocity of air increases as it passes through the constriction at the venturi. II. Pressure decreases due to conversion of a portion of pressure head into kinetic energy. III. The piston moves down and the suction is produced in the cylinder and the induction manifold. IV. Due to pressure difference the jet issues fuel oil into air stream which vapourise forming air fuel mixture. V. The air flows through the carburettor.

    1. III, V, I, II, IV
    2. II, V, III, I, IV
    3. III, II, I, IV, V
    4. II, IV, III, V, I
    Show answer

    Answer (TSPSC's preliminary key): (1) III, V, I, II, IV

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

Cooling & Lubrication

  1. AMVI 2023 Paper 2 (Automobile) · Q13 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which of the following is correct about cooling system of engines? I. The cooling system is provided on an engine because high temperatures reduce strength of piston and cylinder liner. II. The cooling system is provided on an engine because the overheated cylinder may lead to ignition lag in spark ignition engines.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (1) Only I

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

Fuels, Lubricants & Emissions

  1. AMVI 2023 Paper 2 (Automobile) · Q12 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    The lowest temperature at which lubricating oil changes from a liquid state to plastic or solid state is called ______.

    1. cloud point
    2. emulsification point
    3. flash point
    4. pour point
    Show answer

    Answer (TSPSC's preliminary key): (1) cloud point

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  2. AMVI 2023 Paper 2 (Automobile) · Q15 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following is correct about grease? I. Grease is only used where there is a low bearing and shock loads. II. Lubricating grease is a solid to semi solid dispersion of a thickening agent in liquid lubricant.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer (TSPSC's preliminary key): (2) Only II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  3. AMVI 2023 Paper 2 (Automobile) · Q16 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following is correct about lubricating oils? I. Fatty oils exhibit less oiliness than mineral oils of the same viscosity. II. Multigrade oil are not required to change as per ambient temperature. III. Multigrade oil has short warming up period.

    1. Only I and II
    2. Only II
    3. Only II and III
    4. Only I and III
    Show answer

    Answer (TSPSC's preliminary key): (3) Only II and III

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  4. AMVI 2023 Paper 2 (Automobile) · Q20 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Match the following fuel standard to its specialty.

    StandardSpecialty
    I. Iso-octane1. Very prone to knock
    II. Normal heptane2. Measure of ignition quality of diesel
    III. Cetane number3. Very high resistance to knock
    4. Anti knock performance under severe operating conditions
    1. I-4, II-2, III-3
    2. I-3, II-1, III-2
    3. I-1, II-3, III-4
    4. I-2, II-4, III-1
    Show answer

    Answer (TSPSC's preliminary key): (2) I-3, II-1, III-2

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.