TGPSC AMVI Engineering Mechanics & Machine Design previous year questions with answers
Every Engineering Mechanics & Machine Design question asked in the TGPSC AMVI (Assistant Motor Vehicles Inspector) papers on this site, grouped by topic. Answers come from TSPSC's preliminary key; each has a short explanation (free here for a sample, all of them in the practice app).
Practise Engineering Mechanics & Machine Design onlineEngineering Mechanics
What is the value of TAB and TAC in the given diagram? (where sin165° = 0.26)
- TAB = 4950 N, TAC = 3005 N
- TAC = 1810 N, TAB = 4950 N
- TAB = 1810 N, TAB = 3500 N
- TAB = 3500 N, TAC = 1810 N
Show answer
Answer (TSPSC's preliminary key): (2) TAC = 1810 N, TAB = 4950 N
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
What is the total load acting on the beam AB?
- 14400 N
- 7200 N
- 720 N
- 1440 N
Show answer
Answer (TSPSC's preliminary key): (3) 720 N
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The ratio of the limiting force of friction (F) to the normal reaction (R) between two bodies is called ______.
- Coefficient of repose
- Angle of repose
- Frictional power
- Coefficient of friction
Show answer
Answer (TSPSC's preliminary key): (4) Coefficient of friction
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Arrange the following in a decreasing order of the moment of inertia of the given geometric shapes. I. Circle II. Quarter circle III. Semi-circle
- I, II, III
- II, III, I
- I, III, II
- II, I, III
Show answer
Answer (TSPSC's preliminary key): (3) I, III, II
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Arrange the following steps of analysis of machines in a correct order (first to last). I. Dismember the machine and draw a free body diagram of each member. II. Draw a free body diagram of the whole machine. III. Equilibrium equations can be written and solved. IV. Consider multiforce member and show all the forces acting on the member. V. Finally check your solution.
- I, III, IV, II, V
- II, I, III, IV, V
- II, I, IV, III, V
- IV, I, II, III, V
Show answer
Answer (TSPSC's preliminary key): (3) II, I, IV, III, V
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The ratio of load lifted to the effort applied for a lever is called ______.
- Notch sensitivity
- Moment
- Mechanical advantage
- Mechanical efficiency
Show answer
Answer (TSPSC's preliminary key): (3) Mechanical advantage
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Strength of Materials
The change in length (elongation) of bar due to self-weight is given by ______. (P = Load, ρ = density, E = Young’s Modulus, d₁ and d₂ are diameters)
- ρgl/(3E)
- ρgl²/(2E)
- 4PL/(πd₁d₂E)
- ρgL/(2πd₁d₂G)
Show answer
Answer (TSPSC's preliminary key): (2) ρgl²/(2E)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is a correct relation between the material properties? (where (1/m) is poission ratio, K is bulk modulus, E is Young’s modulus)
- K = mE/(3(m − 2))
- K = E/(2(1/m + 1))
- K = 2mE/(m + 2)
- K = mE/(2m + 1)
Show answer
Answer (TSPSC's preliminary key): (1) K = mE/(3(m − 2))
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is a possible shear force diagram for an inclined beam under uniformly distributed load and a point load as shown in a diagram?
- Figure 1
- Figure 2
- Figure 3
- Figure 4
Show answer
Answer (TSPSC's preliminary key): (3) Figure 3
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The maximum deflection for a simply supported beam with a uniformly distributed load is given by ______. (Where w is weight per unit length)
- wl³/(584El)
- 5wl⁴/(384El)
- wl³/(16El)
- wl⁴/(48El)
Show answer
Answer (TSPSC's preliminary key): (2) 5wl⁴/(384El)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is a bending moment diagram for a cantilever beam with a uniformly distributed load?
- Figure 1
- Figure 2
- Figure 3
- Figure 4
Show answer
Answer (TSPSC's preliminary key): (4) Figure 4
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The ratio of lateral strain to linear strain of a body is called ______.
- Resilience
- Deflection
- Poisson's ratio
- Young’s modulus
Show answer
Answer (TSPSC's preliminary key): (3) Poisson's ratio
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is correct about strain in a body? I. Shear strain is defined as the ratio between change in volume and original volume of the body. II. The ratio between the compressing stress and compressive strain is called modulus of elasticity.
- Only I
- Only II
- Both I and II
- Neither I nor II
Show answer
Answer (TSPSC's preliminary key): (2) Only II
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is correct regarding load? I. For a bar with different section subjected to axial load P, the resultant deformation will be summation of change of length of every section. II. For the above diagram the value of P₁ is 52 N.
- Only I
- Only II
- Both I and II
- Neither I nor II
Show answer
Answer (TSPSC's preliminary key): (1) Only I
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A 1 m long rod is fixed at both ends. What is the temperature through which rod can be heated to NOT exceed the thermal stress of 90 MPa? The value of α is 2 × 10⁻⁵ K⁻¹ and E is 90 GPa.
- 90 K
- 180 K
- 50 K
- 100 K
Show answer
Answer (TSPSC's preliminary key): (3) 50 K
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is correct regarding thermal stress? I. If the supports yield by an amount Δ, the change in length will be summation of l α T and Δ. II. The stress of the supports yield by an amount Δ is (αt − Δ/l) E. (where l = length of the original body, α = coefficient of thermal expansion)
- Only I
- Only II
- Both I and II
- Neither I nor II
Show answer
Answer (TSPSC's preliminary key): (2) Only II
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is correct regarding elasticity of a body? I. In elasticity, the body regains its shape after force is removed. II. The resistance force remains even after load is removed. III. The body can regain its original shape after load removed upto elastic limit.
- Only I
- II and III only
- I and III only
- I and II only
Show answer
Answer (TSPSC's preliminary key): (3) I and III only
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is correct regarding shearing force, bending moment and loading condition on the beam? I. A point load at a section on the beam will cause sudden change in shear force. II. A point load at a section on the beam will results in sudden change in bending moment. III. When there is no load between two point, then shear force does not change.
- Only I
- II and III only
- I and III only
- II only
Show answer
Answer (TSPSC's preliminary key): (3) I and III only
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match the following bending moment diagram with the conditions.
- I-1, II-2, III-3, IV-4
- I-2, II-1, III-3, IV-4
- I-2, II-3, III-4, IV-1
- I-1, II-4, III-2, IV-3
Show answer
Answer (TSPSC's preliminary key): (4) I-1, II-4, III-2, IV-3
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is a correctly matched pair regarding section modulus of different section?
- Hollow circular section : Z = (π/32)(D⁴ − d⁴)/(D/2)
- Solid circular section : Z = (π/32)d³
- Solid semi-circular section : Z = (3π/64)d³
- Hollow circular section : Z = (π/14)(D⁴ − d⁴)
Show answer
Answer (TSPSC's preliminary key): (2) Solid circular section : Z = (π/32)d³
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Arrange the following in the increasing order of maximum bending moment for the given loading condition.
- I, II, III
- II, III, I
- III, II, I
- III, I, II
Show answer
Answer (TSPSC's preliminary key): (4) III, I, II
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which one of the following is a correctly matched pair?
Section Distance from the neutral axis to the extreme fibre I. Triangle h/2 II. Hollow rectangle h/2 III. I-section h/3 IV. Hollow circle (d − d₁)/2, (where d = outer diameter and d₁ = inner diameter) - Only I
- Only II
- II and III
- Only IV
Show answer
Answer (TSPSC's preliminary key): (2) Only II
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Theory of Machines
Which of the following gives the coefficient of fluctuation of speed of a flywheel? (where N₁ = Maximum speed during cycle and N₂ is minimum speed during the cycle)
- Cₛ = (N₁ + N₂)/(N₁ − N₂)
- Cₛ = (N₁ − N₂)/(2(N₁ + N₂))
- Cₛ = 2(N₁ − N₂)/(N₁ + N₂)
- Cₛ = 2(N₁ + N₂)/(N₁ − N₂)
Show answer
Answer (TSPSC's preliminary key): (3) Cₛ = 2(N₁ − N₂)/(N₁ + N₂)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is the advantage of the involute gears? I. The centre distance for a pair of involute gear can be varied within limits without changing the velocity ratio. II. The interference does not occur at all in this type of gears.
- Only I
- Only II
- Both I and II
- Neither I nor II
Show answer
Answer (TSPSC's preliminary key): (1) Only I
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is a correctly matched pair regarding the classification of gears based on the position of axes of shafts?
- Mitres : Intersecting and non-parallel
- Spur gear : Non-parallel and non-intersecting
- Helical gear : Intersecting and non-parallel
- Spiral gear : Parallel and non-intersecting
Show answer
Answer (TSPSC's preliminary key): (1) Mitres : Intersecting and non-parallel
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Machine Design
The ratio of maximum stress to the working stress of a material is called ______.
- Strain
- Poisson’s ratio
- Factor of safety
- Young modulus
Show answer
Answer (TSPSC's preliminary key): (3) Factor of safety
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The stresses which vary from one value of tensile to same value of compressive or vice versa of the beam are known as ______.
- repeated stress
- bending stress
- fluctuating stress
- completely reversed stress
Show answer
Answer (TSPSC's preliminary key): (4) completely reversed stress
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The surface joining the crest and root of the screw threads is called ______.
- pitch
- slope
- lead
- flank
Show answer
Answer (TSPSC's preliminary key): (4) flank
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The perpendicular distance between the centre lines of the successive rows in riveted joints is called ______.
- pitch
- marginal pitch
- back pitch
- diagonal pitch
Show answer
Answer (TSPSC's preliminary key): (3) back pitch
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which one of the following is related to the crushing of the rivets? (where, α = coefficient of thermal expansion, ΔT = change in temperature, σc = crushing stress, p = pitch of rivets, d = diameter of rivet hole, t = thickness of the plate and n = number rivets, Pc = crushing resistance)
- Pc = n.d.t.σc
- Pc = n(π/4).d². σc
- Pc = (p − d)t. σc
- Pc = α ΔT
Show answer
Answer (TSPSC's preliminary key): (1) Pc = n.d.t.σc
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is correct regarding leaf spring?
- It consists of a number of flat plates of varying lengths.
- In this spring, fluid behave as a compressive spring.
- This type of springs are helical in shape and used under compressive load only.
- It is made of a wire coiled in the form of a helix.
Show answer
Answer (TSPSC's preliminary key): (1) It consists of a number of flat plates of varying lengths.
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is the advantage of rolling contact bearings over sliding contact bearings? I. They have high resistance to shock loading. II. They have low starting and running friction except at very high speeds.
- Only I
- Only II
- Both I and II
- Neither I nor II
Show answer
Answer (TSPSC's preliminary key): (2) Only II
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is correct regarding springs? I. For the springs connected in series, the total deflection of the springs is summation of the deflection of each spring. II. For the springs connected in series, the combined stiffness of the spring is sum of the stiffness of each spring. III. For the springs connected in parallel, the total load acting on it is the sum of the loads acting on individual springs.
- I and II
- II and III
- I and III
- Only III
Show answer
Answer (TSPSC's preliminary key): (3) I and III
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is correct regarding the sunk keys? I. A rectangular sunk key with a head at one end is called splines. II. A key attached as one member of a pair and which permits relative axial movement is known as woodruff key. III. Woodruff key’s advantage is it accommodates itself to any taper in the hub or boss of the mating piece.
- Only I
- II and III
- Only III
- I and III only
Show answer
Answer (TSPSC's preliminary key): (3) Only III
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match the following method with the equation for combination of stresses. (where σv = variable stress, σm = mean stress, σu = ultimate stress, σe = endurance limit for reversed loading, Kf = fatigue stress concentration factor, F.S. = factor of safety, σy = yielding stress)
Equation for combination of stress Method I. 1/F.S. = (σm/σu)² F.S. + σv.Kf/σe 1. Soderberg method II. 1/F.S. = σm/σu + σv.Kf/σe 2. Gerber method III. 1/F.S. = σm/σy + σv.Kf/σe 3. Goodman method - I-1, II-3, III-2
- I-2, II-1, III-3
- I-3, II-2, III-1
- I-2, II-3, III-1
Show answer
Answer (TSPSC's preliminary key): (4) I-2, II-3, III-1
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
For a same tensile load, arrange the following in an increasing order of maximum stress, given the theoretical stress concentration factor is (1 + 2a/b). (where r = radius of the circle)
- I, II, III
- II, I, III
- II, III, I
- I, III, II
Show answer
Answer (TSPSC's preliminary key): (3) II, III, I
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Arrange the following steps of procedure to solve design problem in a correct order (first to last). I. Synthesis II. Material selection III. Recognition of need IV. Detailed drawing V. Modification VI. Production VII. Analysis of forces VIII. Design of elements (size and stresses)
- III, I, VII, II, VIII, V, IV, VI
- II, III, V, VI, I, VIII, VII, IV
- VI, I, II, III, V, IV, VIII, VII
- IV, II, III, I, VII, VIII, V, VI
Show answer
Answer (TSPSC's preliminary key): (1) III, I, VII, II, VIII, V, IV, VI
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Arrange the following steps in a correct order (first to last) of design procedure for journal bearing. I. Determine the bearing length by choosing ratio of l/d. II. Check the bearing pressure for a probable satisfactory value. III. Determine the heat generated. IV. Determine the operating value of ZN/p for the assumed bearing temperature and check this value. V. Determine the thermal equilibrium to see that the heat dissipated at least equal to heat generated. VI. Determine the coefficient of friction. VII. In case the heat generated is more than the heat dissipated than bearing is artificially cooled by water.
- I, II, IV, VI, III, V, VII
- II, I, III, V, VI, IV, VII
- I, II, VII, IV, VI, V, III
- III, V, VI, II, I, IV, VII
Show answer
Answer (TSPSC's preliminary key): (1) I, II, IV, VI, III, V, VII
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.