Learn with Anil · APPSC AMVI (Assistant Motor Vehicle Inspector) PYQsPractise online →Subscribe ₹149

APPSC AMVI 2026 Paper 2 Automobile Engineering question paper with answers

APPSC Assistant Motor Vehicle Inspector 2026: Paper II (Automobile Engineering). Paper II: Automobile Engineering (diploma standard: thermodynamics, IC engines, chassis and transmission, auto electricals, mechanics and machine design, manufacturing, Motor Vehicles Act and transport), 150 questions, 300 marks, 150 minutes, in English. Notification 21/2025 · Series A, held on 28 January 2026. All four options with the answer from APPSC's final key, plus a short explanation for every question (the first 10 here, all of them in the app).

ఏపీపీఎస్సీ అసిస్టెంట్ మోటార్ వెహికల్ ఇన్‌స్పెక్టర్ (AMVI) పేపర్-2 ఆటోమొబైల్ ఇంజనీరింగ్ 2026 ప్రశ్నపత్రం సమాధానాలతో

Attempt this paper · 150 min timerMake a topic-wise quiz

The correct answer to every question is free on this page, and so are the explanations of the first 10. For all 150 explanations, practise the paper in the app with the ₹149 All-in-One Pass, one payment for every exam on the site.

Subjects in this paper

All 150 questions

  1. Q1 · Thermodynamics & Heat Transfer · Thermodynamics

    A system is in thermodynamic equilibrium when

    1. It exchanges mass but not energy with its surroundings
    2. It exchanges both mass and energy with its surroundings
    3. Macroscopic variables like pressure, volume and temperature do not change with time
    4. It exchanges energy but not mass with its surroundings
    Show answer

    Answer: (3) Macroscopic variables like pressure, volume and temperature do not change with time

    A system is in thermodynamic equilibrium when it is at the same time in thermal, mechanical and chemical equilibrium, so its macroscopic properties such as pressure, volume and temperature are uniform and do not change with time, with no net internal flows. Whether a system exchanges mass, energy or both with its surroundings only tells us whether it is open or closed; it does not decide whether the system is in equilibrium.

  2. Q2 · Thermodynamics & Heat Transfer · Thermodynamics

    The Zeroth Law of Thermodynamics states that if two systems are each in thermal equilibrium with a third system, then

    1. They are in mechanical equilibrium
    2. They are in chemical equilibrium
    3. They are in thermal equilibrium with each other
    4. They are in a state of total thermodynamic equilibrium
    Show answer

    Answer: (3) They are in thermal equilibrium with each other

    The Zeroth Law says that if bodies A and B are each in thermal equilibrium with a third body C, then A and B are in thermal equilibrium with each other: there is no net heat flow when they are brought into contact, because they are at the same temperature. It is the basis of temperature measurement, the third body being the thermometer. It says nothing about mechanical or chemical equilibrium.

  3. Q3 · Thermodynamics & Heat Transfer · Thermodynamics

    Which of the following is not an example of a pure substance ?

    1. Water (H₂O)
    2. Nitrogen (N₂)
    3. Air (a mixture of gases like O₂, N₂, Ar)
    4. Helium (He)
    Show answer

    Answer: (3) Air (a mixture of gases like O₂, N₂, Ar)

    A pure substance has a fixed and uniform chemical composition throughout. Water, nitrogen and helium are single chemical species and qualify. Air is a mixture of nitrogen, oxygen, argon and other gases. It behaves like a pure substance only while it remains a gas of uniform composition; when it is partly liquefied, its components condense at different temperatures and the liquid and vapour have different compositions, so air is not a true pure substance.

  4. Q4 · Thermodynamics & Heat Transfer · Thermodynamics

    The Mollier diagram is a plot of

    1. Temperature and entropy
    2. Temperature and enthalpy
    3. Pressure and enthalpy
    4. Enthalpy and entropy
    Show answer

    Answer: (4) Enthalpy and entropy

    The Mollier diagram, devised by Richard Mollier, plots enthalpy (h) on the vertical axis against entropy (s) on the horizontal axis, usually for steam. On this h–s chart an isentropic expansion is a vertical line and the enthalpy drop can be read directly, which makes it convenient for nozzle and turbine calculations. The temperature–entropy plot is the T–s diagram, and the pressure–enthalpy (p–h) chart is mainly used for refrigerants.

  5. Q5 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    For a fixed amount of heat supplied and a fixed compression ratio, the thermal efficiency of the air-standard cycle follows the order

    1. Otto > Diesel > Dual
    2. Otto > Dual > Diesel
    3. Diesel > Otto > Dual
    4. Dual > Otto > Diesel
    Show answer

    Answer: (2) Otto > Dual > Diesel

    For the same compression ratio and the same heat input, the Otto cycle adds all its heat at constant volume at the end of compression, so the gas then expands through the full ratio, rejects the least heat and is the most efficient. The Diesel cycle adds heat at constant pressure while the gas expands, so it rejects the most heat. The dual cycle adds part at constant volume and part at constant pressure and lies between: η Otto > η Dual > η Diesel.

  6. Q6 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The Stirling cycle consists of

    1. Two isothermal and two constant pressure processes
    2. Two isothermal and two constant volume processes
    3. Two isothermal and two adiabatic processes
    4. Two adiabatic processes and one constant volume processes
    Show answer

    Answer: (2) Two isothermal and two constant volume processes

    The Stirling cycle consists of isothermal compression, constant-volume heat addition, isothermal expansion and constant-volume heat rejection. With a perfect regenerator, which stores the heat rejected at constant volume and returns it later, its efficiency equals that of the Carnot cycle working between the same temperatures. Two isothermal and two constant-pressure processes make the Ericsson cycle, and two isothermal and two adiabatic processes make the Carnot cycle.

  7. Q7 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The diagram factor is defined as the ratio of

    1. Brake power to indicated power
    2. Indicated work done to brake work done
    3. Area of the actual indicator diagram to the area of the theoretical indicator diagram
    4. Thermal efficiency to mechanical efficiency
    Show answer

    Answer: (3) Area of the actual indicator diagram to the area of the theoretical indicator diagram

    Diagram factor = area of the actual indicator diagram ÷ area of the theoretical (hypothetical) indicator diagram, which equals the ratio of the actual to the theoretical mean effective pressure. It allows for losses such as valve throttling, heat transfer and the rounding of the diagram's corners, and it is always less than 1. The ratio of brake power to indicated power (option 1) is the mechanical efficiency.

  8. Q8 · Engineering Mechanics & Machine Design · Theory of Machines

    The radial distance from the pitch circle to the root of the tooth is known as the

    1. Addendum
    2. Clearance
    3. Dedendum
    4. Whole depth
    Show answer

    Answer: (3) Dedendum

    In gear terminology the dedendum is the radial distance from the pitch circle to the root (dedendum) circle, while the addendum is the radial distance from the pitch circle to the tip (addendum) circle. The whole depth is addendum plus dedendum. Clearance is the radial gap between the tip of a tooth and the root of the mating gear, equal to the dedendum minus the addendum.

  9. Q9 · Engineering Mechanics & Machine Design · Theory of Machines

    What is the correct mathematical formula for the module of a gear ? (Where D is the pitch circle diameter and N is the number of teeth)

    1. D/N
    2. D/(2N)
    3. 2D/N
    4. 3D/N
    Show answer

    Answer: (1) D/N

    The module m is the pitch circle diameter divided by the number of teeth, m = D/N, usually expressed in millimetres. It is the reciprocal of the diametral pitch (N/D). The circular pitch is π times the module, p = πD/N = πm, and two gears can mesh only if they have the same module. For example, a gear with a pitch circle diameter of 100 mm and 50 teeth has a module of 2 mm.

  10. Q10 · Engineering Mechanics & Machine Design · Theory of Machines

    In a simple gear train, how is the driven gear's motion related to the driver gear if there is an odd number of gears ?

    1. Opposite direction
    2. Same direction
    3. Does not depends on gear ratio
    4. Depends on gear ratio
    Show answer

    Answer: (2) Same direction

    Each external mesh reverses the direction of rotation. With an odd number of gears in a simple train (for example driver, one idler and driven) there is an even number of meshes, so the driven gear turns in the same direction as the driver; with an even number of gears it turns the opposite way. Idlers change only the direction, not the speed ratio, which depends only on the teeth of the driver and the driven gear.

  11. Q11 · Engineering Mechanics & Machine Design · Theory of Machines

    In an epicyclic gear train, what is the purpose of the arm (or carrier) ?

    1. It is a fixed, stationary gear
    2. It carries the planet gears and rotates
    3. It is the primary output shaft
    4. It fixes the sun gear's position
    Show answer

    Answer: (2) It carries the planet gears and rotates

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  12. Q12 · Engineering Mechanics & Machine Design · Strength of Materials

    What is the primary factor that distinguishes the torsional shear stress distribution in a solid shaft compared to a hollow shaft of the same outer diameter, when subjected to the same torque ?

    1. Shear stress is zero at the center of both shafts
    2. Shear stress is maximum at the center of the hollow shaft but zero at the center of the solid shaft
    3. Shear stress is zero at the inner surface of the hollow shaft but uniform across the solid shaft
    4. Shear stress is highest at the outer surface of the hollow shaft, while the solid shaft's stress increases linearly from the center to the outer surface
    Show answer

    Answer: (4) Shear stress is highest at the outer surface of the hollow shaft, while the solid shaft's stress increases linearly from the center to the outer surface

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  13. Q13 · Engineering Mechanics & Machine Design · Strength of Materials

    For a solid shaft under pure torsion, how does the angle of twist (θ) change if the shaft's length (L) is doubled, while the polar moment of inertia (J) and modulus of rigidity (G) remain constant ?

    1. It remains the same
    2. It is halved
    3. It doubles
    4. It is quadrupled
    Show answer

    Answer: (3) It doubles

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  14. Q14 · Engineering Mechanics & Machine Design · Machine Design

    When a shaft experiences both a bending moment (M) and torque (T) simultaneously, what is the nature of the stresses induced ?

    1. Only shear stress due to torque is present
    2. Only normal stress due to bending is present
    3. Only shear stress due to bending is present
    4. Both normal stress (from bending) and shear stress (from torque) are developed in the shaft
    Show answer

    Answer: (4) Both normal stress (from bending) and shear stress (from torque) are developed in the shaft

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  15. Q15 · Engineering Mechanics & Machine Design · Engineering Mechanics

    A body slides down a 45° inclined plane in twice the time it would take on a frictionless surface. What is the coefficient of kinetic friction, μₖ ?

    1. 0.33
    2. 0.75
    3. 0.5
    4. 1.0
    Show answer

    Answer: (2) 0.75

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  16. Q16 · Engineering Mechanics & Machine Design · Machine Design

    A screw is considered self-locking if

    1. The friction angle is less than the lead angle
    2. The friction angle is greater than the lead angle
    3. The friction angle is equal to the lead angle
    4. The friction angle is half the lead angle
    Show answer

    Answer: (2) The friction angle is greater than the lead angle

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  17. Q17 · Engineering Mechanics & Machine Design · Machine Design

    What is the primary function of a screw jack ?

    1. To convert linear motion into rotary motion
    2. To convert rotary motion into linear motion to lift or lower heavy loads
    3. To measure the pitch of a screw
    4. To create a locking mechanism for a nut
    Show answer

    Answer: (2) To convert rotary motion into linear motion to lift or lower heavy loads

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  18. Q18 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which statement correctly compares flash point and fire point ?

    1. The fire point is always lower than the flash point.
    2. The flash point and fire point are the same temperature.
    3. The fire point is typically higher than the flash point.
    4. The flash point is higher than fire point.
    Show answer

    Answer: (3) The fire point is typically higher than the flash point.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  19. Q19 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following fuels has the highest calorific value ?

    1. Wood
    2. Coal
    3. LPG
    4. Petrol
    Show answer

    Answer: (3) LPG

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  20. Q20 · Thermodynamics & Heat Transfer · Thermodynamics

    A device used for measuring heat exchange is called a

    1. Thermometer
    2. Joule meter
    3. Calorimeter
    4. Pressure gauge
    Show answer

    Answer: (3) Calorimeter

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  21. Q21 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following is the chemical that is used as the reference standard for a Cetane number of 100 ?

    1. Heptane
    2. Octane
    3. Hexadecane (Cetane)
    4. Naphthalene
    Show answer

    Answer: (3) Hexadecane (Cetane)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  22. Q22 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is an advantage of a multi-cylinder engine over a single-cylinder engine of the same total displacement ?

    1. Higher low-end torque
    2. Simpler construction and lower manufacturing costs
    3. Smoother operation with less vibration
    4. Better fuel efficiency at low power demands
    Show answer

    Answer: (3) Smoother operation with less vibration

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  23. Q23 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The primary function of a pre-whirl chamber is to

    1. Increase the engine's compression ratio
    2. Create a high-velocity, swirling motion to improve fuel-air mixing
    3. Cool the incoming air charge
    4. Allow for the use of a high-pressure common-rail fuel system
    Show answer

    Answer: (2) Create a high-velocity, swirling motion to improve fuel-air mixing

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  24. Q24 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following factors increases the ignition delay period in a CI engine ?

    1. Increased compression ratio
    2. Increased air turbulence
    3. Supercharging
    4. Lower cetane number fuel
    Show answer

    Answer: (4) Lower cetane number fuel

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  25. Q25 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following factors can increase the tendency of knocking in a Compression Ignition (CI) engine ?

    1. A longer ignition delay period
    2. Using a fuel with a higher cetane number
    3. A lower compression ratio
    4. A lower temperature of the unburnt fuel-air mixture
    Show answer

    Answer: (1) A longer ignition delay period

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  26. Q26 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    What is the typical firing order for a four-cylinder inline engine ?

    1. 1-2-3-4
    2. 1-3-2-4
    3. 1-3-4-2
    4. 4-3-2-1
    Show answer

    Answer: (3) 1-3-4-2

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  27. Q27 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Why is the firing order of an engine so important ?

    1. It determines the engine's horsepower rating
    2. It ensures the engine's balance, efficiency and performance by distributing power strokes evenly
    3. It is a purely aesthetic choice in engine design
    4. It affects the fuel type the engine can use
    Show answer

    Answer: (2) It ensures the engine's balance, efficiency and performance by distributing power strokes evenly

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  28. Q28 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is not a function of piston rings ?

    1. To seal high-pressure gases
    2. To help in detonation
    3. To maintain sufficient lubrication
    4. To transfer heat to the cylinder wall
    Show answer

    Answer: (2) To help in detonation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  29. Q29 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Piston rings are commonly made from which material ?

    1. Aluminum alloy
    2. Brass
    3. Cast iron or alloy cast iron
    4. Steel
    Show answer

    Answer: (3) Cast iron or alloy cast iron

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  30. Q30 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    During normal operation of an internal combustion engine, where is the highest temperature typically found on the piston ?

    1. Piston pin boss
    2. Skirt of the piston
    3. Top ring groove
    4. Center of the piston crown
    Show answer

    Answer: (4) Center of the piston crown

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  31. Q31 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which type of injection is considered the most accurate ?

    1. Throttle body injection
    2. Manifold injection
    3. Direct injection
    4. Port injection
    Show answer

    Answer: (3) Direct injection

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  32. Q32 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    What is the purpose of the venturi in a carburetor ?

    1. To increase the fuel flow
    2. To decrease the pressure and draw fuel into the airstream
    3. To regulate the amount of air entering the engine
    4. To provide a consistent air-fuel ratio
    Show answer

    Answer: (2) To decrease the pressure and draw fuel into the airstream

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  33. Q33 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    What is the purpose of internal baffles inside a fuel tank ?

    1. To increase the tank's volume
    2. To reduce fuel sloshing during movement
    3. To allow for easier fuel delivery
    4. To help the fuel pump run cooler
    Show answer

    Answer: (2) To reduce fuel sloshing during movement

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  34. Q34 · Engineering Mechanics & Machine Design · Theory of Machines

    The unbalanced mass in a single-cylinder engine is balanced by counteracting the centrifugal force of the disturbing mass with the centrifugal force of a balancing mass. This is done for which of the following ?

    1. Dynamic balancing
    2. Neither static nor dynamic balancing
    3. Both static and dynamic balancing
    4. Static balancing
    Show answer

    Answer: (4) Static balancing

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  35. Q35 · Engineering Mechanics & Machine Design · Theory of Machines

    The primary unbalanced force in a single-cylinder engine is maximum when the crank angle (θ) is

    1. 0° and 90°
    2. 0° and 180°
    3. 90° and 180°
    4. 180° and 360°
    Show answer

    Answer: (2) 0° and 180°

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  36. Q36 · Engineering Mechanics & Machine Design · Theory of Machines

    What is the purpose of a balancing mass in a single-cylinder engine ?

    1. To increase the speed of the engine
    2. To balance the rotating parts and reduce vibration
    3. To provide torque to the engine
    4. To reduce the engine's stroke
    Show answer

    Answer: (2) To balance the rotating parts and reduce vibration

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  37. Q37 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which type of lubrication system is most commonly used in two-stroke engines ?

    1. Splash lubrication system
    2. Wet sump lubrication system
    3. Pressure lubrication system
    4. Mist lubrication system
    Show answer

    Answer: (4) Mist lubrication system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  38. Q38 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which of the following is a component of a pressure lubrication system ?

    1. Scoop on the connecting rod
    2. Oil mixed with fuel
    3. Oil pump that forces oil through channels
    4. Oil splashed onto components from a reservoir
    Show answer

    Answer: (3) Oil pump that forces oil through channels

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  39. Q39 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which of the following is a key advantage of the liquid cooling system ?

    1. It is very cheap
    2. It provides even cooling throughout the engine
    3. It is dependent only on the supply of water
    4. It absorbs a considerable amount of power from the engine
    Show answer

    Answer: (2) It provides even cooling throughout the engine

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  40. Q40 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    In an air-cooled engine, what component helps to increase the surface area for heat dissipation ?

    1. Radiator fan
    2. Pressure cap
    3. Extended fins
    4. Circulating air
    Show answer

    Answer: (3) Extended fins

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  41. Q41 · Automobile Chassis & Transmission · Clutch & Gearbox

    What is the role of the dog clutch in a synchromesh gearbox after synchronization ?

    1. To initiate the speed matching process
    2. To provide the final positive engagement between the gear and the shaft
    3. To disengage the gears during a shift
    4. To absorb vibrations during operation
    Show answer

    Answer: (2) To provide the final positive engagement between the gear and the shaft

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  42. Q42 · Automobile Chassis & Transmission · Clutch & Gearbox

    What is the primary function of a torque converter in an automatic transmission ?

    1. To engage and disengage the engine from the transmission
    2. To transmit power from the engine to the transmission
    3. To provide a fluid coupling to transmit torque from the engine to the transmission
    4. To control the gear selection and shift points
    Show answer

    Answer: (3) To provide a fluid coupling to transmit torque from the engine to the transmission

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  43. Q43 · Automobile Chassis & Transmission · Clutch & Gearbox

    Which of the following is a basic component of most automatic transmissions ?

    1. Flywheel
    2. Planetary gear set
    3. Friction clutch
    4. Clutch pedal
    Show answer

    Answer: (2) Planetary gear set

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  44. Q44 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    What is the purpose of a slip joint in a propeller shaft ?

    1. To allow the shaft to bend sideways
    2. To transfer torque at an angle
    3. To transmit torque when the shafts are not parallel
    4. To allow the shaft to change length due to expansion or contraction
    Show answer

    Answer: (4) To allow the shaft to change length due to expansion or contraction

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  45. Q45 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Which type of joint is used to allow the propeller shaft to transmit torque at an angle ?

    1. Universal joint
    2. Hinge joint
    3. Ball and socket joint
    4. Pivot joint
    Show answer

    Answer: (1) Universal joint

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  46. Q46 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    A differential allows the rear wheels to rotate at different speeds. This is essential for

    1. Starting the vehicle on a hill
    2. Increasing the vehicle's horsepower
    3. Proper steering during a turn
    4. Applying the brakes
    Show answer

    Answer: (3) Proper steering during a turn

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  47. Q47 · Automobile Chassis & Transmission · Clutch & Gearbox

    Which type of clutch does not require a clutch pedal ?

    1. Single plate
    2. Multi-plate
    3. Centrifugal
    4. Cone
    Show answer

    Answer: (3) Centrifugal

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  48. Q48 · Automobile Chassis & Transmission · Clutch & Gearbox

    In a single plate clutch, what is the function of the pressure plate ?

    1. To apply friction to the clutch disc
    2. To disengage the clutch disc from the flywheel when the pedal is depressed
    3. To hold the clutch disc between the flywheel and itself when the pedal is released
    4. To absorb heat generated during engagement
    Show answer

    Answer: (3) To hold the clutch disc between the flywheel and itself when the pedal is released

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  49. Q49 · Automobile Chassis & Transmission · Clutch & Gearbox

    Why are multi-plate clutches used instead of single plate clutches ?

    1. To reduce torque transmission capacity
    2. To increase the torque transmission capacity
    3. To operate as a wet clutch only
    4. To increase the overall size of the clutch
    Show answer

    Answer: (2) To increase the torque transmission capacity

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  50. Q50 · Automobile Chassis & Transmission · Brakes

    In a disc brake, which component is responsible for applying pressure to the pads ?

    1. Brake drum
    2. Piston in the caliper
    3. Brake fluid
    4. Bleed screw
    Show answer

    Answer: (2) Piston in the caliper

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  51. Q51 · Automobile Chassis & Transmission · Brakes

    What is the main advantage of disc brakes over drum brakes ?

    1. They are generally less expensive
    2. They are less prone to brake fade due to better heat dissipation
    3. They are simpler in design and require less maintenance
    4. They are more effective when the vehicle is in reverse gear
    Show answer

    Answer: (2) They are less prone to brake fade due to better heat dissipation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  52. Q52 · Automobile Chassis & Transmission · Brakes

    Which of these is an advantage of hydraulic brakes over mechanical brakes ?

    1. They require more pedal effort for the same braking effect
    2. They require less pedal effort for the same braking effect
    3. They only provide uniform braking force to one wheel
    4. They are less effective at high speeds
    Show answer

    Answer: (2) They require less pedal effort for the same braking effect

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  53. Q53 · Automobile Chassis & Transmission · Brakes

    Which vehicle type typically uses air brakes due to their size and weight ?

    1. Passenger cars
    2. Motorcycles
    3. Trucks, buses and semi-trailers
    4. Electric scooters
    Show answer

    Answer: (3) Trucks, buses and semi-trailers

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  54. Q54 · Automobile Chassis & Transmission · Steering & Suspension

    When a vehicle turns, the inner front wheel must

    1. Turn at a smaller angle than the outer wheel
    2. Turn at the same angle as the outer wheel
    3. Turn at a greater angle than the outer wheel
    4. Have a negative steering angle
    Show answer

    Answer: (3) Turn at a greater angle than the outer wheel

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  55. Q55 · Automobile Chassis & Transmission · Steering & Suspension

    The condition for correct steering is that all four wheels of a vehicle must

    1. Turn at the same angle
    2. Turn about the same instantaneous center
    3. Have the same turning radius
    4. Be perfectly aligned at all times
    Show answer

    Answer: (2) Turn about the same instantaneous center

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  56. Q56 · Automobile Chassis & Transmission · Steering & Suspension

    What is the primary function of the Ackermann steering mechanism ?

    1. To make all four wheels turn at the same angle
    2. To achieve true rolling by ensuring the wheels turn at different angles when cornering
    3. To provide power steering assist to the driver
    4. To improve fuel efficiency
    Show answer

    Answer: (2) To achieve true rolling by ensuring the wheels turn at different angles when cornering

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  57. Q57 · Automotive Electrical & Electronics · Batteries & Charging

    What is the function of the alternator in a vehicle ?

    1. To provide the initial power to start the engine
    2. To recharge the battery and power the electrical accessories
    3. To convert electrical energy to mechanical energy
    4. To regulate the oil pressure
    Show answer

    Answer: (2) To recharge the battery and power the electrical accessories

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  58. Q58 · Automotive Electrical & Electronics · Batteries & Charging

    Which component converts mechanical energy into electrical energy to charge the battery and power the electrical system ?

    1. Starter motor
    2. Alternator
    3. Regulator
    4. Ignition coil
    Show answer

    Answer: (2) Alternator

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  59. Q59 · Automotive Electrical & Electronics · Lighting, Instruments & Wiring

    What is the purpose of a relay in an automotive electrical circuit ?

    1. To reduce the voltage in the circuit
    2. To increase the resistance of the circuit
    3. To act as a remote-controlled switch, allowing a low-current circuit to control a high-current circuit
    4. To store electrical charge for later use
    Show answer

    Answer: (3) To act as a remote-controlled switch, allowing a low-current circuit to control a high-current circuit

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  60. Q60 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What is the impact of high concentrations of pollutants like sulfur dioxide on the environment ?

    1. Causes a cooling effect in the atmosphere
    2. Is the primary cause of acid rain
    3. Do not cause the formation of smog
    4. Neutralizes acid in water bodies
    Show answer

    Answer: (2) Is the primary cause of acid rain

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  61. Q61 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What is a major exhaust emission from CI (diesel) engines compared to SI (petrol) engines ?

    1. Carbon Monoxide (CO)
    2. Particulates
    3. Sulphur
    4. Unburnt Hydrocarbons (HC)
    Show answer

    Answer: (2) Particulates

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  62. Q62 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following factors increases the tendency for NOₓ formation in an SI engine ?

    1. Decreasing the air-fuel ratio
    2. Increasing the peak combustion temperature
    3. Increasing the ignition delay
    4. Lowering the engine’s compression ratio
    Show answer

    Answer: (2) Increasing the peak combustion temperature

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  63. Q63 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Odor emissions from diesel engines are mainly caused by

    1. Oxides of nitrogen (NOₓ)
    2. Carbon monoxide (CO)
    3. Particulate matter (soot)
    4. Unburnt or partially burnt hydrocarbons, including aldehydes
    Show answer

    Answer: (4) Unburnt or partially burnt hydrocarbons, including aldehydes

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  64. Q64 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Aldehydes in diesel engine exhaust are a type of

    1. Sulfur oxide compound
    2. Particulate matter
    3. Unburnt hydrocarbon (HC)
    4. Inert gas
    Show answer

    Answer: (3) Unburnt hydrocarbon (HC)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  65. Q65 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following operating conditions is a primary cause for high NOₓ emissions in a diesel engine ?

    1. Low combustion temperature
    2. Insufficient oxygen supply
    3. High combustion pressure and temperature with sufficient reaction time
    4. Delayed injection timing
    Show answer

    Answer: (3) High combustion pressure and temperature with sufficient reaction time

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  66. Q66 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Diesel engine exhaust primarily contains which forms of nitrogen oxides ?

    1. N₂O and NO₂
    2. N₂O₄ and N₂O₃
    3. Pure N₂ and O₂
    4. NO and NO₂
    Show answer

    Answer: (4) NO and NO₂

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  67. Q67 · Thermodynamics & Heat Transfer · Refrigeration & Air Conditioning

    What is the function of the condenser in an automotive air-conditioning system ?

    1. It cools the refrigerant
    2. It compresses the refrigerant
    3. It expands the refrigerant
    4. It removes moisture from the refrigerant
    Show answer

    Answer: (1) It cools the refrigerant

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  68. Q68 · Thermodynamics & Heat Transfer · Refrigeration & Air Conditioning

    What is the purpose of the recirculating mode in a car’s air-conditioning ?

    1. To pull in outside air
    2. To increase the use of the AC system
    3. To recycle air already inside the cabin
    4. To turn the AC system off
    Show answer

    Answer: (3) To recycle air already inside the cabin

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  69. Q69 · Automobile Chassis & Transmission · Steering & Suspension

    The outward or inward tilt of a wheel from the vertical is known as

    1. Caster
    2. Toe
    3. Camber
    4. Kingpin inclination
    Show answer

    Answer: (3) Camber

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  70. Q70 · Automobile Chassis & Transmission · Steering & Suspension

    Which of the following steering geometry components is the lateral inward tilt of the steering axis from the vertical ?

    1. Caster angle
    2. Camber
    3. Kingpin inclination
    4. Toe-in
    Show answer

    Answer: (3) Kingpin inclination

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  71. Q71 · Automobile Chassis & Transmission · Steering & Suspension

    A vehicle set with “toe-out” on the front wheels will typically exhibit which handling characteristic ?

    1. Increased straight-line stability at high speeds
    2. Slower and smoother steering response
    3. Enhanced steering sensitivity and quicker turn-in to corners
    4. Reduced tyre wear over time
    Show answer

    Answer: (3) Enhanced steering sensitivity and quicker turn-in to corners

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  72. Q72 · Automobile Chassis & Transmission · Wheels & Tyres

    Where will an underinflated tyre wear the tread most ?

    1. Near the center
    2. Near the edge (both edges)
    3. In the cross direction
    4. Evenly across the surface
    Show answer

    Answer: (2) Near the edge (both edges)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  73. Q73 · Automobile Chassis & Transmission · Wheels & Tyres

    Grooves (tread) are made in the tyres of vehicles to

    1. Allow the tyre to fit the rim better
    2. Make the tyre look more appealing
    3. Improve traction and grip on the road, especially in wet conditions
    4. Reduce the weight of the tyre
    Show answer

    Answer: (3) Improve traction and grip on the road, especially in wet conditions

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  74. Q74 · Materials, Manufacturing & Metrology · Engineering Materials

    Which of the following is a common crystal structure for metals ?

    1. Simple Cubic
    2. Body-Centered Cubic (BCC)
    3. Octagonal
    4. Triangular
    Show answer

    Answer: (2) Body-Centered Cubic (BCC)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  75. Q75 · Materials, Manufacturing & Metrology · Engineering Materials

    Which of the following non-ferrous metals is known for its high electrical and thermal conductivity ?

    1. Lead
    2. Zinc
    3. Aluminum
    4. Tin
    Show answer

    Answer: (3) Aluminum

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  76. Q76 · Materials, Manufacturing & Metrology · Engineering Materials

    Which element is the main component in ferrous metals ?

    1. Zinc
    2. Tin
    3. Copper
    4. Iron
    Show answer

    Answer: (4) Iron

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  77. Q77 · Materials, Manufacturing & Metrology · Engineering Materials

    The ability of a material to be drawn into wires is called

    1. Malleability
    2. Ductility
    3. Toughness
    4. Hardness
    Show answer

    Answer: (2) Ductility

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  78. Q78 · Materials, Manufacturing & Metrology · Metrology & Measurement

    A thermocouple is a type of transducer used to measure

    1. Force
    2. Pressure
    3. Displacement
    4. Temperature
    Show answer

    Answer: (4) Temperature

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  79. Q79 · Automotive Electrical & Electronics · Electronics, Sensors & ECU

    An automatic cruise control system in a car is an example of a

    1. Open-loop system
    2. Closed-loop system
    3. Simple control system
    4. Feedforward control system
    Show answer

    Answer: (2) Closed-loop system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  80. Q80 · Materials, Manufacturing & Metrology · Metrology & Measurement

    Which of the following is commonly used in automobiles and other applications to measure force or weight by converting it into an electrical signal ?

    1. Thermistor
    2. Load cell (Force Transducer)
    3. Thermocouple
    4. Potentiometer
    Show answer

    Answer: (2) Load cell (Force Transducer)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  81. Q81 · Thermodynamics & Heat Transfer · Thermodynamics

    What is the highest possible theoretical efficiency of a heat engine operating with a hot reservoir of furnace gases at 2100 °C when the cooling water available is at 15 °C ?

    1. 0.678 or 67.8%
    2. 0.778 or 77.8%
    3. 0.878 or 87.8%
    4. 0.978 or 97.8%
    Show answer

    Answer: (3) 0.878 or 87.8%

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  82. Q82 · Thermodynamics & Heat Transfer · Thermodynamics

    The specific volume of water when heated at 0 °C

    1. First increases and then decreases
    2. First decreases and then increases
    3. Increases steadily
    4. Decreases steadily
    Show answer

    Answer: (2) First decreases and then increases

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  83. Q83 · Thermodynamics & Heat Transfer · Thermodynamics

    What is the value of absolute zero scale of temperature ?

    1. 273 °C
    2. 273 °K
    3. − 273 °K
    4. 0° K
    Show answer

    Answer: (4) 0° K

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  84. Q84 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The efficiency of an Otto Cycle is 60% and γ = 1.5. What is the compression ratio ?

    1. 4.25
    2. 5.25
    3. 6.25
    4. 7.25
    Show answer

    Answer: (3) 6.25

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  85. Q85 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Mean effective pressure of the Otto Cycle is

    1. Inversely proportional to pressure ratio
    2. Directly proportional to pressure ratio
    3. Proportional to square root of pressure ratio
    4. Does not vary with pressure ratio
    Show answer

    Answer: (2) Directly proportional to pressure ratio

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  86. Q86 · Engineering Mechanics & Machine Design · Theory of Machines

    The product of diametral pitch (P) and circular pitch (p) is

    1. π
    2. 2π
    3. 1
    4. 0
    Show answer

    Answer: (1) π

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  87. Q87 · Engineering Mechanics & Machine Design · Machine Design

    A single reduction gear of 120 kW with a pinion 250 mm pitch circle diameter and 650 r.p.m. is supported in bearings on either side. Calculate the torque transmitted in N-m.

    1. 1765
    2. 1675
    3. 1567
    4. 1176
    Show answer

    Answer: (1) 1765

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  88. Q88 · Engineering Mechanics & Machine Design · Theory of Machines

    The train value of a gear train is

    1. equal to velocity ratio of a gear train
    2. reciprocal of velocity ratio of a gear train
    3. always greater than unity
    4. always less than unity
    Show answer

    Answer: (2) reciprocal of velocity ratio of a gear train

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  89. Q89 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Flash point and fire point are characteristics primarily related to the

    1. Low-temperature behaviour of the fuel
    2. High-temperature behaviour and volatility of the fuel
    3. Purity of the fuel
    4. Viscosity of the fuel
    Show answer

    Answer: (2) High-temperature behaviour and volatility of the fuel

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  90. Q90 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    The fire point of a fuel is the lowest temperature at which its vapor will continue to burn for at least how many seconds after ignition ?

    1. 1 second
    2. 2 seconds
    3. 4 seconds
    4. 5 seconds
    Show answer

    Answer: (4) 5 seconds

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  91. Q91 · Engineering Mechanics & Machine Design · Machine Design

    A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The shaft may be assumed to be made of mild steel with an allowable shear stress of 42 MPa. Determine the torque transmitted by the shaft, neglecting the bending moment on the shaft in N-m.

    1. 80 mm
    2. 90 mm
    3. 70 mm
    4. 50 mm
    Show answer

    Answer: (4) 50 mm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  92. Q92 · Engineering Mechanics & Machine Design · Machine Design

    Which of the following loading is considered for the design of axles ?

    1. Bending moment only
    2. Twisting moment only
    3. Combined bending moment and torsion
    4. Combined action of bending moment, twisting moment and axial thrust
    Show answer

    Answer: (1) Bending moment only

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  93. Q93 · Engineering Mechanics & Machine Design · Machine Design

    When a shaft is subjected to a bending moment M and a twisting moment T, then the equivalent twisting moment is equal to

    1. M + T
    2. M² + T²
    3. √(M² + T²)
    4. √(M² − T²)
    Show answer

    Answer: (3) √(M² + T²)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  94. Q94 · Engineering Mechanics & Machine Design · Machine Design

    Screws used for power transmission should have

    1. low efficiency
    2. high efficiency
    3. very fine threads
    4. strong teeth
    Show answer

    Answer: (2) high efficiency

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  95. Q95 · Engineering Mechanics & Machine Design · Theory of Machines

    A screw jack has square threads and the lead angle of the thread is α. The screw jack will be self locking when the coefficient of friction (μ) is

    1. μ > tan α
    2. μ = sin α
    3. μ = cot α
    4. μ = cosec α
    Show answer

    Answer: (1) μ > tan α

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  96. Q96 · Engineering Mechanics & Machine Design · Engineering Mechanics

    What force would be required to slide it down if the coefficient of friction between body and plane is 0.3 ?

    1. 0 kg
    2. 2 kg
    3. 3 kg
    4. 5 kg
    Show answer

    Answer: (1) 0 kg

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  97. Q97 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    In a C.I. engine squish is created

    1. towards end of compression stroke
    2. at the end of suction stroke
    3. at the beginning of suction stroke
    4. during combustion
    Show answer

    Answer: (1) towards end of compression stroke

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  98. Q98 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Detonation in S.I. engines occurs due to

    1. Preignition of charge before the spark
    2. Sudden ignition of charge before the spark
    3. Autoignition of the charge after the spark is struck
    4. Non availability of fuel
    Show answer

    Answer: (3) Autoignition of the charge after the spark is struck

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  99. Q99 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    The ratings of C.I. engine fuel is given by

    1. Octane Number
    2. Performance Number
    3. Cetane Number
    4. Bearing Number
    Show answer

    Answer: (3) Cetane Number

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  100. Q100 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Bomb Calorimeter is used to find the calorific value of ________ fuel.

    1. Solid
    2. Gaseous
    3. Solid and gaseous
    4. Nuclear
    Show answer

    Answer: (3) Solid and gaseous

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  101. Q101 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    In C.I. engines knocking tendency increases with

    1. Increases in compression ratio
    2. Increasing inlet temperature of air
    3. Decrease in compression ratio
    4. Increasing the coolant temperature
    Show answer

    Answer: (3) Decrease in compression ratio

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  102. Q102 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    In C.I. engines with increase in compression ratio the delay period

    1. Increases
    2. Decreases
    3. First increases and then decreases
    4. Remains unaffected
    Show answer

    Answer: (2) Decreases

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  103. Q103 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The top ring nearest to the piston crown is known as

    1. Compression ring
    2. Oil ring
    3. Scrapper ring
    4. Groove ring
    Show answer

    Answer: (1) Compression ring

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  104. Q104 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    For reducing wear and eliminate scuffling, the piston rings are

    1. Lubricated
    2. Made of cast iron
    3. Provided with stepped groove
    4. Plated with chromium or cadmium
    Show answer

    Answer: (4) Plated with chromium or cadmium

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  105. Q105 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    IC engine pistons are usually made of

    1. Cast Steel
    2. Forged Steel
    3. Phosphor Bronze
    4. Aluminium Alloy
    Show answer

    Answer: (4) Aluminium Alloy

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  106. Q106 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The venturi in carburetor results in

    1. Decrease in air velocity
    2. Increase in air velocity
    3. Decrease in fuel flow
    4. Increase in manifold vacuum
    Show answer

    Answer: (2) Increase in air velocity

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  107. Q107 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Precise petrol injection system is

    1. Direct injection
    2. Sequential injection
    3. Throttle body injection
    4. Port injection
    Show answer

    Answer: (3) Throttle body injection

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  108. Q108 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The fuel injection pressure in solid injection system is around

    1. Less than 10 bar
    2. 10 – 20 bar
    3. 30 – 50 bar
    4. 200 – 250 bar
    Show answer

    Answer: (4) 200 – 250 bar

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  109. Q109 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    ________ regulates the pressure strokes in the fuel injection pump of a diesel engine.

    1. Pump shaft
    2. Control rack
    3. Lift of plunger
    4. Needle valve
    Show answer

    Answer: (2) Control rack

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  110. Q110 · Engineering Mechanics & Machine Design · Theory of Machines

    The primary unbalanced force is maximum when the angle of inclination of the crank with the line of stroke is

    1. 60°
    2. 90°
    3. 180°
    4. 360°
    Show answer

    Answer: (3) 180°

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  111. Q111 · Engineering Mechanics & Machine Design · Theory of Machines

    The partial balancing means

    1. Balancing partially the revolving masses
    2. Balancing partially the reciprocating masses
    3. Best balancing of engines
    4. All of the above
    Show answer

    Answer: (2) Balancing partially the reciprocating masses

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  112. Q112 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Detergents are oil additives used to

    1. Reduce viscosity
    2. Increase fire point
    3. Prevent sludge formation
    4. Prevent foaming
    Show answer

    Answer: (3) Prevent sludge formation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  113. Q113 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Friction that occurs between the layers of oil film is called

    1. Viscous friction
    2. Greasy friction
    3. Dry friction
    4. Boundary friction
    Show answer

    Answer: (1) Viscous friction

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  114. Q114 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    The main purpose of thermostat in an engine cooling system is to

    1. Allow the engine to warm quickly
    2. Prevent the coolant from boiling
    3. Pressurise the system
    4. Indicate to the driver the coolant temperature
    Show answer

    Answer: (1) Allow the engine to warm quickly

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  115. Q115 · Automobile Chassis & Transmission · Clutch & Gearbox

    Two advantages of using helical gears rather than spur gears in a transmission are

    1. Strength and cost
    2. Strength and less end thrust
    3. Noise level and strength
    4. Noise level and economy
    Show answer

    Answer: (3) Noise level and strength

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  116. Q116 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    The adjustment for backlash in a differential is provided between

    1. Crown wheel and sun gear
    2. Sun gear and planet gear
    3. Crown wheel and the drive pinion
    4. Crown wheel and planet gear
    Show answer

    Answer: (3) Crown wheel and the drive pinion

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  117. Q117 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Central portion of the propeller shaft is made from

    1. steel shaft
    2. gun metal shaft
    3. steel tube
    4. cast iron rod
    Show answer

    Answer: (3) steel tube

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  118. Q118 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    The smallest gears inside the differential casing are

    1. pinion gears
    2. sun gears
    3. side gears
    4. ring gears
    Show answer

    Answer: (1) pinion gears

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  119. Q119 · Automobile Chassis & Transmission · Steering & Suspension

    The primary function of a ball and socket joint is to

    1. Allow rotation in one plane only
    2. Allow linear motion only
    3. Allow movement in almost all directions
    4. Restrict all movements
    Show answer

    Answer: (3) Allow movement in almost all directions

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  120. Q120 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Two-piece propeller shaft requires

    1. One universal joint
    2. A centre support bearing
    3. The shaft to be solid
    4. None of the above
    Show answer

    Answer: (2) A centre support bearing

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  121. Q121 · Engineering Mechanics & Machine Design · Machine Design

    A single dry plate clutch is to be designed to transmit 7.5 kW at 900 r.p.m. Find the diameter of the shaft.

    1. 21.6 mm
    2. 26.6 mm
    3. 32.6 mm
    4. 36.6 mm
    Show answer

    Answer: (1) 21.6 mm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  122. Q122 · Automobile Chassis & Transmission · Clutch & Gearbox

    In case of a multiple disc clutch, if n₁ are the number of discs on the driving shaft and n₂ are the number of the discs on the driven shaft, then the number of pairs of contact surfaces will be

    1. n₁ + n₂
    2. n₁ + n₂ − 1
    3. n₁ + n₂ + 1
    4. n₁ − n₂ − 1
    Show answer

    Answer: (2) n₁ + n₂ − 1

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  123. Q123 · Automobile Chassis & Transmission · Clutch & Gearbox

    The coefficient of friction for the clutch facing is approximately

    1. 0.1
    2. 0.4
    3. 0.8
    4. 1.2
    Show answer

    Answer: (2) 0.4

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  124. Q124 · Automobile Chassis & Transmission · Clutch & Gearbox

    The maximum value of axial force at the clutch which a driver can apply while driving without getting fatigued is approximately

    1. 10N
    2. 100N
    3. 500N
    4. 5000N
    Show answer

    Answer: (2) 100N

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  125. Q125 · Automobile Chassis & Transmission · Brakes

    In drum type brakes the fluid on releasing return to the master cylinder due to the action of the piston returns spring and

    1. bypass port
    2. wheel cylinder spring
    3. compensating port
    4. brake shoe retractor spring
    Show answer

    Answer: (2) wheel cylinder spring

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  126. Q126 · Automobile Chassis & Transmission · Brakes

    The hand brake usually operates on

    1. Rear wheels
    2. Front wheels
    3. Right side wheels
    4. Left side wheels
    Show answer

    Answer: (1) Rear wheels

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  127. Q127 · Automobile Chassis & Transmission · Brakes

    What is the efficiency of hydraulic braking system ?

    1. 20% – 30%
    2. 40% – 50%
    3. 65% – 75%
    4. About 90%
    Show answer

    Answer: (4) About 90%

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  128. Q128 · Automobile Chassis & Transmission · Brakes

    ________ is not a part of hydraulic braking system.

    1. Wheel Cylinder
    2. Master Cylinder
    3. Steering Mechanism
    4. Brake Pedal
    Show answer

    Answer: (3) Steering Mechanism

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  129. Q129 · Automobile Chassis & Transmission · Brakes

    The brake employed in cars are usually operated

    1. mechanically
    2. hydraulically
    3. by means of engine vacuum
    4. by compressed air
    Show answer

    Answer: (2) hydraulically

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  130. Q130 · Automobile Chassis & Transmission · Brakes

    Fading of brake occurs

    1. at high speed
    2. at low speed
    3. during continuous application
    4. when brake lining
    Show answer

    Answer: (3) during continuous application

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  131. Q131 · Automobile Chassis & Transmission · Brakes

    The brake bleeding process removes from the system

    1. Air
    2. Vacuum
    3. Excess fluid
    4. Excess pressure
    Show answer

    Answer: (1) Air

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  132. Q132 · Automobile Chassis & Transmission · Steering & Suspension

    The steering ratio for manual steering of cars is approximately

    1. 5
    2. 15
    3. 50
    4. 100
    Show answer

    Answer: (2) 15

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  133. Q133 · Automobile Chassis & Transmission · Steering & Suspension

    The turning circle for a car is approximately

    1. 1 metre
    2. 2 metres
    3. 10 metres
    4. 30 metres
    Show answer

    Answer: (3) 10 metres

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  134. Q134 · Automobile Chassis & Transmission · Steering & Suspension

    A vehicle has a wheelbase (L) of 2 meters and a wheel track (W, distance between front wheel pivots) of 1.5 meters. Calculate the required turning angle for the outer front wheel (ϕ) if the inner front wheel is steered to an angle (θ) of 30 degrees.

    1. Approximately 25 degrees
    2. Approximately 22 degrees
    3. Approximately 20 degrees
    4. Approximately 28 degrees
    Show answer

    Answer: (2) Approximately 22 degrees

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  135. Q135 · Automotive Electrical & Electronics · Starting & Ignition

    Three components of primary ignition circuit are

    1. Contact breaker, condenser and distributor cap
    2. Contact breaker, ignition coil and spark plugs
    3. Contact breaker, ignition switch and condenser
    4. Contact breaker, ignition switch and rotor
    Show answer

    Answer: (3) Contact breaker, ignition switch and condenser

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  136. Q136 · Automotive Electrical & Electronics · Starting & Ignition

    The contact breaker points are opened by the cam and closed by the

    1. Same cam
    2. Centrifugal force
    3. Magnetic force
    4. Spring tension
    Show answer

    Answer: (4) Spring tension

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  137. Q137 · Automotive Electrical & Electronics · Lighting, Instruments & Wiring

    The two quantities used for specifying electrical wire are

    1. The colour and length
    2. The length and diameter
    3. The diameter and number of strands
    4. The colour and diameter
    Show answer

    Answer: (3) The diameter and number of strands

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  138. Q138 · Automotive Electrical & Electronics · Batteries & Charging

    The frequency of a vibrating contact type for d.c. generator is

    1. 20 per second
    2. 200 per second
    3. 20 per minute
    4. 200 per minute
    Show answer

    Answer: (2) 200 per second

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  139. Q139 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The carbon accumulation in an engine cylinder results in

    1. Increase of effective compression ratio
    2. Increase of volumetric efficiency
    3. Increase of clearance volume
    4. Increase of ignition time
    Show answer

    Answer: (1) Increase of effective compression ratio

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  140. Q140 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Due to which of the following reasons the piston rings are plated with chromium, cadmium or phosphate ?

    1. To prevent clogging
    2. To improve heat transfer
    3. To reduce wear and eliminate scuffing
    4. To improve surface finish
    Show answer

    Answer: (3) To reduce wear and eliminate scuffing

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  141. Q141 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Carbon Monoxide emission from S.I. engine are higher when the engine is

    1. Idling
    2. Cruising
    3. Accelerating
    4. Decelerating
    Show answer

    Answer: (1) Idling

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  142. Q142 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Orsat flue gas analysis gives

    1. Mass analysis of wet products of combustion
    2. Volumetric analysis of dry products of combustion
    3. Mass analysis of dry products of combustion
    4. Volumetric analysis of wet products of combustion
    Show answer

    Answer: (2) Volumetric analysis of dry products of combustion

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  143. Q143 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Flame Ionisation Detector is used for measuring

    1. CO
    2. HC
    3. NOₓ
    4. CO₂
    Show answer

    Answer: (2) HC

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  144. Q144 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Chemiluminescence technique is used to measure

    1. NOₓ
    2. CO
    3. CO₂
    4. Smoke intensity
    Show answer

    Answer: (1) NOₓ

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  145. Q145 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Non-dispersive infra-red analyser is widely accepted instrument for measuring

    1. NOₓ
    2. HC
    3. CO
    4. CO₂
    Show answer

    Answer: (3) CO

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  146. Q146 · Materials, Manufacturing & Metrology · Engineering Materials

    What is depth of hardened layer by flame hardening of steel wheel ?

    1. 0.15 mm
    2. 0.8 mm
    3. 0.35 mm
    4. 1.2 mm
    Show answer

    Answer: (2) 0.8 mm

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  147. Q147 · Materials, Manufacturing & Metrology · Engineering Materials

    By what process maximum hardness is obtained for a steel part ?

    1. Carburizing
    2. Nitriding
    3. Cyaniding
    4. Same hardness in all processes
    Show answer

    Answer: (2) Nitriding

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  148. Q148 · Materials, Manufacturing & Metrology · Engineering Materials

    The ratio of E of a whisker of mild steel to E of a bulk material is

    1. 4
    2. 5
    3. 40
    4. 50
    Show answer

    Answer: (2) 5

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  149. Q149 · Thermodynamics & Heat Transfer · Refrigeration & Air Conditioning

    Which of the following is a possible reason for flushing an A/C condenser ?

    1. To replace the old refrigerant with new refrigerant
    2. To remove sludge and debris
    3. To remove moisture
    4. To improve cooling efficiency
    Show answer

    Answer: (2) To remove sludge and debris

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  150. Q150 · Automobile Chassis & Transmission · Wheels & Tyres

    The disadvantage of radial ply tyre compared to cross ply tyre is

    1. uncomfortable tried at low speeds
    2. uncomfortable ride at high speeds
    3. higher corning power
    4. lower rolling resistance
    Show answer

    Answer: (1) uncomfortable tried at low speeds

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.