APPSC AMVI Engineering Mechanics & Machine Design previous year questions with answers
Every Engineering Mechanics & Machine Design question asked in the APPSC AMVI (Assistant Motor Vehicle Inspector) papers on this site, grouped by topic. Answers come from APPSC's final keys; each has a short explanation (free here for a sample, all of them in the practice app).
Practise Engineering Mechanics & Machine Design onlineEngineering Mechanics
A body slides down a 45° inclined plane in twice the time it would take on a frictionless surface. What is the coefficient of kinetic friction, μₖ ?
- 0.33
- 0.75
- 0.5
- 1.0
Show answer
Answer: (2) 0.75
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
What force would be required to slide it down if the coefficient of friction between body and plane is 0.3 ?
- 0 kg
- 2 kg
- 3 kg
- 5 kg
Show answer
Answer: (1) 0 kg
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Fluid friction between two lubricated surfaces are due to
Show answer
Answer: Viscosity and Oiliness
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Coefficient of Friction is,__________
Show answer
Answer: limiting friction (F) / Normal reaction (R_N) between the two bodies
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following is not the unit of a power?
Show answer
Answer: kcal/kg sec
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Strength of Materials
What is the primary factor that distinguishes the torsional shear stress distribution in a solid shaft compared to a hollow shaft of the same outer diameter, when subjected to the same torque ?
- Shear stress is zero at the center of both shafts
- Shear stress is maximum at the center of the hollow shaft but zero at the center of the solid shaft
- Shear stress is zero at the inner surface of the hollow shaft but uniform across the solid shaft
- Shear stress is highest at the outer surface of the hollow shaft, while the solid shaft's stress increases linearly from the center to the outer surface
Show answer
Answer: (4) Shear stress is highest at the outer surface of the hollow shaft, while the solid shaft's stress increases linearly from the center to the outer surface
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
For a solid shaft under pure torsion, how does the angle of twist (θ) change if the shaft's length (L) is doubled, while the polar moment of inertia (J) and modulus of rigidity (G) remain constant ?
- It remains the same
- It is halved
- It doubles
- It is quadrupled
Show answer
Answer: (3) It doubles
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
1 MPa (Mega Pascal): __________ N/mm²
Show answer
Answer: 1 ×10^0
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
__________ is correct expression for Poisson’s ratio
Show answer
Answer: Lateral strain / Longitudinal strain
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Hook’s law holds good up to
Show answer
Answer: Elastic Limit
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Normal Strain may be
Show answer
Answer: All of the given options
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
__________ is the property by virtue of which certain material return back to their original position after the removal of the external force
Show answer
Answer: Elasticity
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The dimensions of Young’s modulus of elasticity are given by
Show answer
Answer: M¹L⁻¹T⁻²
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Modulus of rigidity is defined as the ratio of
Show answer
Answer: Shear stress to shear strain
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The relationship between modulus of elasticity E, bulk modulus K and Poisson’s Ratio μ = is,
Show answer
Answer: E = 3K (1 - 2μ)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Two shafts A and B are made of the same material. The diameter of the shaft A is twice as that of shaft B. The power transmitted by the shaft A will be __________ of shaft B.
Show answer
Answer: Eight times
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Section modulus Z is expresses as, where, I = Moment of inertia of the cross- section about the neutral axis, Y = Distance from the neutral axis to the extreme fibre
Show answer
Answer: I/Y
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The maximum energy that can be stored in a body due to external loading up to the elastic limit is called
Show answer
Answer: proof resilience
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Theory of Machines
The radial distance from the pitch circle to the root of the tooth is known as the
- Addendum
- Clearance
- Dedendum
- Whole depth
Show answer
Answer: (3) Dedendum
In gear terminology the dedendum is the radial distance from the pitch circle to the root (dedendum) circle, while the addendum is the radial distance from the pitch circle to the tip (addendum) circle. The whole depth is addendum plus dedendum. Clearance is the radial gap between the tip of a tooth and the root of the mating gear, equal to the dedendum minus the addendum.
What is the correct mathematical formula for the module of a gear ? (Where D is the pitch circle diameter and N is the number of teeth)
- D/N
- D/(2N)
- 2D/N
- 3D/N
Show answer
Answer: (1) D/N
The module m is the pitch circle diameter divided by the number of teeth, m = D/N, usually expressed in millimetres. It is the reciprocal of the diametral pitch (N/D). The circular pitch is π times the module, p = πD/N = πm, and two gears can mesh only if they have the same module. For example, a gear with a pitch circle diameter of 100 mm and 50 teeth has a module of 2 mm.
In a simple gear train, how is the driven gear's motion related to the driver gear if there is an odd number of gears ?
- Opposite direction
- Same direction
- Does not depends on gear ratio
- Depends on gear ratio
Show answer
Answer: (2) Same direction
Each external mesh reverses the direction of rotation. With an odd number of gears in a simple train (for example driver, one idler and driven) there is an even number of meshes, so the driven gear turns in the same direction as the driver; with an even number of gears it turns the opposite way. Idlers change only the direction, not the speed ratio, which depends only on the teeth of the driver and the driven gear.
In an epicyclic gear train, what is the purpose of the arm (or carrier) ?
- It is a fixed, stationary gear
- It carries the planet gears and rotates
- It is the primary output shaft
- It fixes the sun gear's position
Show answer
Answer: (2) It carries the planet gears and rotates
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The unbalanced mass in a single-cylinder engine is balanced by counteracting the centrifugal force of the disturbing mass with the centrifugal force of a balancing mass. This is done for which of the following ?
- Dynamic balancing
- Neither static nor dynamic balancing
- Both static and dynamic balancing
- Static balancing
Show answer
Answer: (4) Static balancing
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The primary unbalanced force in a single-cylinder engine is maximum when the crank angle (θ) is
- 0° and 90°
- 0° and 180°
- 90° and 180°
- 180° and 360°
Show answer
Answer: (2) 0° and 180°
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
What is the purpose of a balancing mass in a single-cylinder engine ?
- To increase the speed of the engine
- To balance the rotating parts and reduce vibration
- To provide torque to the engine
- To reduce the engine's stroke
Show answer
Answer: (2) To balance the rotating parts and reduce vibration
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The product of diametral pitch (P) and circular pitch (p) is
- π
- 2π
- 1
- 0
Show answer
Answer: (1) π
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The train value of a gear train is
- equal to velocity ratio of a gear train
- reciprocal of velocity ratio of a gear train
- always greater than unity
- always less than unity
Show answer
Answer: (2) reciprocal of velocity ratio of a gear train
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A screw jack has square threads and the lead angle of the thread is α. The screw jack will be self locking when the coefficient of friction (μ) is
- μ > tan α
- μ = sin α
- μ = cot α
- μ = cosec α
Show answer
Answer: (1) μ > tan α
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The primary unbalanced force is maximum when the angle of inclination of the crank with the line of stroke is
- 60°
- 90°
- 180°
- 360°
Show answer
Answer: (3) 180°
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The partial balancing means
- Balancing partially the revolving masses
- Balancing partially the reciprocating masses
- Best balancing of engines
- All of the above
Show answer
Answer: (2) Balancing partially the reciprocating masses
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Match the following type gear trains with their functions.
Gear type Functions (A) Simple gear train (i) The gear train in which axis of first gear and last gear is co-axial. (B) Compound gear train (ii) The gear train which consists of more than one gear on any shaft. (C) Epi-cyclic gear train (iii) The gear train in which the axis of one or more gear moves relative to the fixed axis of another gear. (D) Reverted gear train (iv) The gear train which consists of only one gear on each shaft. - (A). - (i), (B). - (iii), (C).- (ii) and (D). - (iv)
- (A). - (iii), (B). - (ii), (C).- (iv) and (D). - (i)
- (A). - (iv), (B). - (ii), (C).- (iii) and (D). - (i)
- (A). - (iv), (B). - (i), (C).- (iii) and (D). - (ii)
Show answer
Answer: (3) (A). - (iv), (B). - (ii), (C).- (iii) and (D). - (i)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The maximum magnitude of the unbalanced force perpendicular to the line of stroke of an engine to cause the variation in pressure between the wheel and the rail such that the vehicle vibrates vigorously is known as:
- Swaying Couple
- Hammer Blow
- Resonance
- Natural Vibration
Show answer
Answer: (2) Hammer Blow
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
In balancing of single cylinder engine, the rotating unbalance is:
- Completely made zero and so also the reciprocating unbalance
- Completely made zero and the reciprocating unbalance is partially reduced
- Partially reduced and the reciprocating unbalance is completely made zero
- Partially reduced and so also the reciprocating unbalance
Show answer
Answer: (2) Completely made zero and the reciprocating unbalance is partially reduced
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
How can the critical whirling speed of a shaft be increased?
- Reducing its length
- Reducing its diameter
- Increasing its diameter
- Increasing its weight
Show answer
Answer: (3) Increasing its diameter
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
__________ is used to connect non-intersecting and non-parallel shafts
Show answer
Answer: Spiral gears
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The diametral pitch of a gear is given by, Where, D=Pitch circle diameter T= Number of teeth,
Show answer
Answer: T/D
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Contact ratio is known as __________
Show answer
Answer: Length of arc of contact / the circular pitch of a gear
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Mitre gears are used for
Show answer
Answer: equal speed
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
In worm and wheel, the shaft axes are
Show answer
Answer: Perpendicular to each other
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The number of teeth on each of the two equal spur gears in mesh are 35 and the module is 6 mm then, __________ is the circular pitch.
Show answer
Answer: 18.8
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
In a screw jack, the effort required to lift the load S is __________ Where, A = Helix angle, and B = Angle of friction
Show answer
Answer: P = S tan (A+ B)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Machine Design
When a shaft experiences both a bending moment (M) and torque (T) simultaneously, what is the nature of the stresses induced ?
- Only shear stress due to torque is present
- Only normal stress due to bending is present
- Only shear stress due to bending is present
- Both normal stress (from bending) and shear stress (from torque) are developed in the shaft
Show answer
Answer: (4) Both normal stress (from bending) and shear stress (from torque) are developed in the shaft
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A screw is considered self-locking if
- The friction angle is less than the lead angle
- The friction angle is greater than the lead angle
- The friction angle is equal to the lead angle
- The friction angle is half the lead angle
Show answer
Answer: (2) The friction angle is greater than the lead angle
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
What is the primary function of a screw jack ?
- To convert linear motion into rotary motion
- To convert rotary motion into linear motion to lift or lower heavy loads
- To measure the pitch of a screw
- To create a locking mechanism for a nut
Show answer
Answer: (2) To convert rotary motion into linear motion to lift or lower heavy loads
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A single reduction gear of 120 kW with a pinion 250 mm pitch circle diameter and 650 r.p.m. is supported in bearings on either side. Calculate the torque transmitted in N-m.
- 1765
- 1675
- 1567
- 1176
Show answer
Answer: (1) 1765
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The shaft may be assumed to be made of mild steel with an allowable shear stress of 42 MPa. Determine the torque transmitted by the shaft, neglecting the bending moment on the shaft in N-m.
- 80 mm
- 90 mm
- 70 mm
- 50 mm
Show answer
Answer: (4) 50 mm
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Which of the following loading is considered for the design of axles ?
- Bending moment only
- Twisting moment only
- Combined bending moment and torsion
- Combined action of bending moment, twisting moment and axial thrust
Show answer
Answer: (1) Bending moment only
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
When a shaft is subjected to a bending moment M and a twisting moment T, then the equivalent twisting moment is equal to
- M + T
- M² + T²
- √(M² + T²)
- √(M² − T²)
Show answer
Answer: (3) √(M² + T²)
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Screws used for power transmission should have
- low efficiency
- high efficiency
- very fine threads
- strong teeth
Show answer
Answer: (2) high efficiency
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
A single dry plate clutch is to be designed to transmit 7.5 kW at 900 r.p.m. Find the diameter of the shaft.
- 21.6 mm
- 26.6 mm
- 32.6 mm
- 36.6 mm
Show answer
Answer: (1) 21.6 mm
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Read the given statement and conclusions carefully and select the correct option. Statement: Self-locking screw jack means when the rotational force on the screw is removed, it will remain motionless and will not rotate backwards. Conclusions: I. Self-locking screw jacks are safer compared to hydraulic jack which is not self-locking. II. Single start trapezoidal type screws are typically self-locking. III. All screw jacks with double start lifting screws are also considered self-locking.
- Statement and all the conclusions I, II and III are true.
- Statement is incorrect, but conclusions I and II are true.
- Statement is true, but conclusions I, II and III are false.
- Only statement and conclusions I and II are true.
Show answer
Answer: (4) Only statement and conclusions I and II are true.
A screw is self-locking when the friction angle is at least equal to the helix (lead) angle, so the load cannot turn it back once the effort is removed; the statement is true. Single-start square or trapezoidal screws have a small lead angle and are normally self-locking, which makes such jacks safe to leave under load (I and II). A double-start screw has twice the lead and a larger helix angle, so it is often not self-locking; III is false.
In an automobile, what type of stress induced in the shafts due to the transmission of torque?
- Bending stress
- Shear stress
- Principle stress
- Torsional stress
Show answer
Answer: (2) Shear stress
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
In an automobile, what type of stress induced in the shafts due to the forces acting upon machine elements like gears, pulleys etc.?
- Bending stress
- Shear stress
- Principle stress
- Hoop stress
Show answer
Answer: (1) Bending stress
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
In an automobile, what is the typical cross-sectional shape of the shaft?
- Circular
- Rectangular
- Triangular
- Tubular
Show answer
Answer: (4) Tubular
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
__________ is the advantage of gear drive as compared to belt, rope and chain drives
Show answer
Answer: All of the given options
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Nominal diameter and core diameter of the screw thread is denoted by d₀ and dc respectively, then the mean diameter of the screw is given by __________
Show answer
Answer: (d0 + dc)/2
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
The capacity of a brake depends upon __________
Show answer
Answer: All of the given options
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.
Factor of safety is defined as
Show answer
Answer: Ultimate stress / Permissible stress
Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.