Learn with Anil · APPSC AMVI (Assistant Motor Vehicle Inspector) PYQsPractise online →Subscribe ₹149

APPSC AMVI IC Engines, Fuels & Emissions previous year questions with answers

Every IC Engines, Fuels & Emissions question asked in the APPSC AMVI (Assistant Motor Vehicle Inspector) papers on this site, grouped by topic. Answers come from APPSC's final keys; each has a short explanation (free here for a sample, all of them in the practice app).

Practise IC Engines, Fuels & Emissions online

Engine Fundamentals & Cycles

  1. AMVI 2026 Paper 2 (Automobile) · Q5 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    For a fixed amount of heat supplied and a fixed compression ratio, the thermal efficiency of the air-standard cycle follows the order

    1. Otto > Diesel > Dual
    2. Otto > Dual > Diesel
    3. Diesel > Otto > Dual
    4. Dual > Otto > Diesel
    Show answer

    Answer: (2) Otto > Dual > Diesel

    For the same compression ratio and the same heat input, the Otto cycle adds all its heat at constant volume at the end of compression, so the gas then expands through the full ratio, rejects the least heat and is the most efficient. The Diesel cycle adds heat at constant pressure while the gas expands, so it rejects the most heat. The dual cycle adds part at constant volume and part at constant pressure and lies between: η Otto > η Dual > η Diesel.

  2. AMVI 2026 Paper 2 (Automobile) · Q6 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The Stirling cycle consists of

    1. Two isothermal and two constant pressure processes
    2. Two isothermal and two constant volume processes
    3. Two isothermal and two adiabatic processes
    4. Two adiabatic processes and one constant volume processes
    Show answer

    Answer: (2) Two isothermal and two constant volume processes

    The Stirling cycle consists of isothermal compression, constant-volume heat addition, isothermal expansion and constant-volume heat rejection. With a perfect regenerator, which stores the heat rejected at constant volume and returns it later, its efficiency equals that of the Carnot cycle working between the same temperatures. Two isothermal and two constant-pressure processes make the Ericsson cycle, and two isothermal and two adiabatic processes make the Carnot cycle.

  3. AMVI 2026 Paper 2 (Automobile) · Q7 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The diagram factor is defined as the ratio of

    1. Brake power to indicated power
    2. Indicated work done to brake work done
    3. Area of the actual indicator diagram to the area of the theoretical indicator diagram
    4. Thermal efficiency to mechanical efficiency
    Show answer

    Answer: (3) Area of the actual indicator diagram to the area of the theoretical indicator diagram

    Diagram factor = area of the actual indicator diagram ÷ area of the theoretical (hypothetical) indicator diagram, which equals the ratio of the actual to the theoretical mean effective pressure. It allows for losses such as valve throttling, heat transfer and the rounding of the diagram's corners, and it is always less than 1. The ratio of brake power to indicated power (option 1) is the mechanical efficiency.

  4. AMVI 2026 Paper 2 (Automobile) · Q22 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is an advantage of a multi-cylinder engine over a single-cylinder engine of the same total displacement ?

    1. Higher low-end torque
    2. Simpler construction and lower manufacturing costs
    3. Smoother operation with less vibration
    4. Better fuel efficiency at low power demands
    Show answer

    Answer: (3) Smoother operation with less vibration

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  5. AMVI 2026 Paper 2 (Automobile) · Q26 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    What is the typical firing order for a four-cylinder inline engine ?

    1. 1-2-3-4
    2. 1-3-2-4
    3. 1-3-4-2
    4. 4-3-2-1
    Show answer

    Answer: (3) 1-3-4-2

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  6. AMVI 2026 Paper 2 (Automobile) · Q27 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Why is the firing order of an engine so important ?

    1. It determines the engine's horsepower rating
    2. It ensures the engine's balance, efficiency and performance by distributing power strokes evenly
    3. It is a purely aesthetic choice in engine design
    4. It affects the fuel type the engine can use
    Show answer

    Answer: (2) It ensures the engine's balance, efficiency and performance by distributing power strokes evenly

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  7. AMVI 2026 Paper 2 (Automobile) · Q28 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is not a function of piston rings ?

    1. To seal high-pressure gases
    2. To help in detonation
    3. To maintain sufficient lubrication
    4. To transfer heat to the cylinder wall
    Show answer

    Answer: (2) To help in detonation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  8. AMVI 2026 Paper 2 (Automobile) · Q29 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Piston rings are commonly made from which material ?

    1. Aluminum alloy
    2. Brass
    3. Cast iron or alloy cast iron
    4. Steel
    Show answer

    Answer: (3) Cast iron or alloy cast iron

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  9. AMVI 2026 Paper 2 (Automobile) · Q30 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    During normal operation of an internal combustion engine, where is the highest temperature typically found on the piston ?

    1. Piston pin boss
    2. Skirt of the piston
    3. Top ring groove
    4. Center of the piston crown
    Show answer

    Answer: (4) Center of the piston crown

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  10. AMVI 2026 Paper 2 (Automobile) · Q84 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The efficiency of an Otto Cycle is 60% and γ = 1.5. What is the compression ratio ?

    1. 4.25
    2. 5.25
    3. 6.25
    4. 7.25
    Show answer

    Answer: (3) 6.25

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  11. AMVI 2026 Paper 2 (Automobile) · Q85 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Mean effective pressure of the Otto Cycle is

    1. Inversely proportional to pressure ratio
    2. Directly proportional to pressure ratio
    3. Proportional to square root of pressure ratio
    4. Does not vary with pressure ratio
    Show answer

    Answer: (2) Directly proportional to pressure ratio

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  12. AMVI 2026 Paper 2 (Automobile) · Q103 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The top ring nearest to the piston crown is known as

    1. Compression ring
    2. Oil ring
    3. Scrapper ring
    4. Groove ring
    Show answer

    Answer: (1) Compression ring

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  13. AMVI 2026 Paper 2 (Automobile) · Q104 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    For reducing wear and eliminate scuffling, the piston rings are

    1. Lubricated
    2. Made of cast iron
    3. Provided with stepped groove
    4. Plated with chromium or cadmium
    Show answer

    Answer: (4) Plated with chromium or cadmium

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  14. AMVI 2026 Paper 2 (Automobile) · Q105 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    IC engine pistons are usually made of

    1. Cast Steel
    2. Forged Steel
    3. Phosphor Bronze
    4. Aluminium Alloy
    Show answer

    Answer: (4) Aluminium Alloy

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  15. AMVI 2026 Paper 2 (Automobile) · Q139 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The carbon accumulation in an engine cylinder results in

    1. Increase of effective compression ratio
    2. Increase of volumetric efficiency
    3. Increase of clearance volume
    4. Increase of ignition time
    Show answer

    Answer: (1) Increase of effective compression ratio

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  16. AMVI 2026 Paper 2 (Automobile) · Q140 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Due to which of the following reasons the piston rings are plated with chromium, cadmium or phosphate ?

    1. To prevent clogging
    2. To improve heat transfer
    3. To reduce wear and eliminate scuffing
    4. To improve surface finish
    Show answer

    Answer: (3) To reduce wear and eliminate scuffing

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  17. AMVI 2023 Paper 2 (Automobile) · Q5 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Match the following four internally reversible processes used in a four-stroke Otto cycle as shown in figure.

    List IList II
    (A) Isentropic compression(i) 2-3
    (B) Constant-volume heat addition(ii) 1-2
    (C) Isentropic expansion(iii) 4-1
    (D) Constant-volume heat rejection(iv) 3-4
    Figure for question 5
    1. (A)-(i), (B)-(ii), (C)-(iii) and (D)-(iv)
    2. (A)-(iv), (B)-(iii), (C)-(ii) and (D)-(i)
    3. (A)-(ii), (B)-(i), (C)-(iv) and (D)-(iii)
    4. (A)-(ii), (B)-(iv), (C)-(i) and (D)-(iii)
    Show answer

    Answer: (3) (A)-(ii), (B)-(i), (C)-(iv) and (D)-(iii)

    On the P–V diagram of the air-standard Otto cycle, 1–2 is isentropic (constant-entropy) compression as the volume falls, 2–3 is heat addition at constant volume (vertical rise in pressure), 3–4 is isentropic expansion (power stroke), and 4–1 is heat rejection at constant volume (vertical drop in pressure). So A–(ii), B–(i), C–(iv) and D–(iii).

  18. AMVI 2023 Paper 2 (Automobile) · Q7 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Select the option that is true regarding the following two statements labelled Assertion (A) and Reason (R). Assertion (A): The C.I. engine is found to be more efficient than the S.I. engine. Reason (R): Modern C.I. engines operate on a dual-cycle, which has efficiency greater than the Otto cycle.

    1. Both A and R are individually true, and R is the correct explanation of A.
    2. Both A and R are individually true, but R is not the correct explanation of A.
    3. A is true, but R is false.
    4. A is false, but R is true.
    Show answer

    Answer: (2) Both A and R are individually true, but R is not the correct explanation of A.

    C.I. engines are more efficient mainly because they run at much higher compression ratios (about 14–22 against 8–12 for S.I. engines), with lean mixtures and no throttling losses. Modern high-speed C.I. engines are modelled by the dual (limited-pressure) cycle, which is more efficient than the Otto cycle when both work to the same peak pressure; for the same compression ratio, however, the Otto cycle is the most efficient. So R holds only for the same peak pressure; the real reason for A is the higher compression ratio, and R does not explain A.

  19. AMVI 2023 Paper 2 (Automobile) · Q8 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Match the following air standard cycles with their working fluids

    List IList II
    (A) Air standard cycle(i) A mixture of air and fuel is a working fluid
    (B) Actual cycle(ii) Generation of energy by burning of fuel with air
    (iii) Air is working fluid
    (iv) No internal heat generation
    (v) This cycle is completely closed
    (vi) Energy is generated inside of the engine
    1. (A)-(iii), (iv) and (v); (B)-(i), (ii) and (vi)
    2. (A)-(i), (ii) and (vi); (B)-(iii), (iv) and (v)
    3. (A)-(ii), (i) and (iv); (B)-(iii), (v) and (vi)
    4. (A)-(i), (ii) and (iii); (B)-(iv), (v) and (vi)
    Show answer

    Answer: (1) (A)-(iii), (iv) and (v); (B)-(i), (ii) and (vi)

    The air-standard cycle is an idealisation: the working fluid is air alone, treated as a perfect gas, heat is added from an external source instead of by combustion (no internal heat generation), and the same air is recirculated in a closed cycle. In the actual engine cycle the working fluid is an air–fuel mixture, energy is released by burning the fuel with air, and this happens inside the engine cylinder.

  20. AMVI 2023 Paper 2 (Automobile) · Q43 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is NOT a function of piston rings?

    1. Sealing the combustion chamber
    2. Controlling the thickness of the oil film on the cylinder wall
    3. Carrying the heat away from the cylinder into the piston
    4. Providing hydrodynamic lubrication
    Show answer

    Answer: (3) Carrying the heat away from the cylinder into the piston

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  21. AMVI 2023 Paper 2 (Automobile) · Q44 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following types of piston rings located in the ring groove is closest to the crankcase?

    1. Oil ring
    2. Compression ring
    3. Wiper ring
    4. Heat transfer ring
    Show answer

    Answer: (1) Oil ring

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  22. AMVI 2023 Paper 2 (Automobile) · Q45 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The piston is not parallel sided but tapered, usually with a barrel form as shown in the figure. The correct position for piston ______ measurement (point x) should be verified with the product supplier, as the exact point will vary by application.

    Figure for question 45
    1. bottom dead centre
    2. skirt diameter
    3. top dead centre
    4. Gudgeon pin thickness
    Show answer

    Answer: (2) skirt diameter

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  23. AMVI 2023 Paper 2 (Automobile) · Q47 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following parts of an engine is shown in the figure?

    Figure for question 47
    1. Piston cylinder
    2. Cylinder head
    3. Cylinder block
    4. Crankcase
    Show answer

    Answer: (3) Cylinder block

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  24. AMVI 2023 Paper 2 (Automobile) · Q48 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following types of pistons is shown in the figure?

    Figure for question 48
    1. Domed piston
    2. Flat top piston
    3. Dished piston
    4. Relief valve piston
    Show answer

    Answer: (3) Dished piston

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  25. AMVI 2023 Paper 2 (Automobile) · Q50 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The firing order in an engine is important because a correct firing order can cause ________.

    1. low pollution
    2. minimum vibration
    3. good air cooling
    4. low fuel consumption
    Show answer

    Answer: (2) minimum vibration

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  26. AMVI 2023 Paper 2 (Automobile) · Q65 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following options about the given assertion and reason is correct? Assertion (A): The air standard efficiency of the diesel cycle decreases as the load is increased. Reason (R): With increase of load, cut-off ratio increases.

    1. Both A and R are individually true and R is the correct explanation of A.
    2. Both A and R are individually true but R is not the correct explanation of A.
    3. A is true but R is false.
    4. A is false but R is true.
    Show answer

    Answer: (1) Both A and R are individually true and R is the correct explanation of A.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  27. AMVI 2023 Paper 2 (Automobile) · Q86 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    What is the temperature of the intake valve?

    1. 200°C to 300°C
    2. 300°C to 400°C
    3. 400°C to 500°C
    4. 500°C to 600°C
    Show answer

    Answer: (1) 200°C to 300°C

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  28. AMVI 2023 Paper 2 (Automobile) · Q87 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    During a power stroke, the downward moment of the piston isdone due to which pressure or force?

    1. Fuel pressure
    2. Gas pressure
    3. Solid pressure
    4. Liquid pressure
    Show answer

    Answer: (2) Gas pressure

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  29. AMVI 2023 Paper 2 (Automobile) · Q88 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Match the columns.

    IC Engine TerminologyFunction
    (i) Bore(a) Distance between TDC and BDC
    (ii) Stroke(b) Combined volume of all engines
    (iii) Engine displacement(c) SI engine
    (iv) Spark plug(d) Internal diameter of cylinder
    1. (i)-c, (ii)-d, (iii)-a, (iv)-b
    2. (i)-d, (ii)-a, (iii)-b, (iv)-c
    3. (i)-a, (ii)-b, (iii)-c, (iv)-d
    4. (i)-c, (ii)-a, (iii)-d, (iv)-b
    Show answer

    Answer: (2) (i)-d, (ii)-a, (iii)-b, (iv)-c

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  30. AMVI 2023 Paper 2 (Automobile) · Q89 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Read the given statement and conclusions carefully. Which of the given conclusions logically follow(s) from the statement? Statement: A piston is a component of reciprocating engines, reciprocating pumps, gas compressors, hydraulic cylinders and pneumatic cylinders, among other similar mechanisms. Conclusions: I) It is the moving component that is contained by a cylinder and is made gas-tight by piston rings. II) Its purpose is to transfer force from expanding gas in the cylinder to the crankshaft via a piston rod.

    1. Only Conclusion I follows
    2. Only Conclusion II follows
    3. Both conclusions follow
    4. The statement is true but the conclusions are false
    Show answer

    Answer: (3) Both conclusions follow

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  31. AMVI 2023 Paper 2 (Automobile) · Q98 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In which stroke of the petrol engine, ‘exhaust gases’ is released to the atmosphere?

    1. Exhaust stroke
    2. Power stroke
    3. Compression stroke
    4. Intake stroke
    Show answer

    Answer: (1) Exhaust stroke

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  32. AMVI 2023 Paper 2 (Automobile) · Q103 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In which type of engine, petrol is used as fuel?

    1. Steam engine
    2. Spark ignition engine
    3. Diesel engine
    4. Turbine engine
    Show answer

    Answer: (2) Spark ignition engine

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  33. AMVI 2023 Paper 2 (Automobile) · Q119 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which process is responsible for expelling the exhaust gases from the cylinder during the exhaust stroke of the engine?

    1. Knocking
    2. Combustion
    3. Scavenging
    4. Ignition
    Show answer

    Answer: (3) Scavenging

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  34. AMVI 2023 Paper 2 (Automobile) · Q120 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Exhaust gases are pushed out of the cylinder by the motion of what component in an engine?

    1. Spark plug
    2. Carburettor
    3. Piston
    4. Crankshaft
    Show answer

    Answer: (3) Piston

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  35. AMVI 2023 Paper 2 (Automobile) · Q121 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following statements is correct regarding the exhaust stroke in Four-stroke Otto Cycle Engine? I. The suction valve remains closed and exhaust valve is open. II. As the piston moves from BDC to TDC, it pushes the gases out through exhaust valves.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer: (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  36. AMVI 2023 Paper 2 (Automobile) · Q122 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In a four-stroke diesel engine cycle, when does the exhaust valve typically open?

    1. At the beginning of the compression stroke
    2. Just before the end of expansion
    3. During the intake stroke
    4. At the start of the power stroke
    Show answer

    Answer: (2) Just before the end of expansion

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  37. AMVI 2023 Paper 2 (Automobile) · Q125 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The exhaust of spent gases from the cylinder of an automobile engine is done so that ______.

    1. the engine can run silently
    2. fuel efficiency is improved
    3. fresh charge may be sucked in
    4. the exhaust note becomes louder
    Show answer

    Answer: (3) fresh charge may be sucked in

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  38. AMVI 2023 Paper 2 (Automobile) · Q126 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In a four stroke diesel cycle engine, during which piston movement does it push gases through the exhaust valves?

    1. From TDC towards BDC
    2. From BDC towards TDC
    3. From TDC to BDC and back to TDC
    4. No piston movement required
    Show answer

    Answer: (2) From BDC towards TDC

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  39. AMVI 2019 Paper 2 (Automobile) · Q4 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    __________ is the compression ratio for positive ignition (PI) engine.

    Show answer

    Answer: 6 to 10

    Positive (spark) ignition engines are usually given compression ratios of about 6 to 10, because a higher ratio raises the temperature and pressure of the end gas and causes knock (detonation) with ordinary petrol. Compression ignition (diesel) engines use about 16 to 22, since they need hot compressed air for self-ignition of the fuel. Modern petrol engines with knock sensors and direct injection often run above 10:1.

  40. AMVI 2019 Paper 2 (Automobile) · Q11 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The process of cleaning the cylinder, after the expansion stroke, is called

    Show answer

    Answer: Scavenging

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  41. AMVI 2019 Paper 2 (Automobile) · Q16 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The ratio of the actual volume of gas taken into the cylinder during suction stroke to the piston displacement volume is called

    Show answer

    Answer: Volumetric efficiency

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  42. AMVI 2019 Paper 2 (Automobile) · Q17 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Morse test is used to calculate __________

    Show answer

    Answer: Brake Power

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  43. AMVI 2019 Paper 2 (Automobile) · Q19 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Usually crankcase is made of -------

    Show answer

    Answer: both Aluminium and Cast iron

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  44. AMVI 2019 Paper 2 (Automobile) · Q20 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Inside a cylinder, dissociation is __________ temperature.

    Show answer

    Answer: Increases with

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  45. AMVI 2019 Paper 2 (Automobile) · Q35 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The Indicated power of an engine is __________ the brake power

    Show answer

    Answer: >

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  46. AMVI 2019 Paper 2 (Automobile) · Q36 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Petrol car engine has four cylinders of 75 mm bore and 85 mm stroke with 8 compression ratios, __________ is the cubic capacity of the engine

    Show answer

    Answer: 376

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  47. AMVI 2019 Paper 2 (Automobile) · Q38 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    4 cylinder in-line engine has a __________ firing order

    Show answer

    Answer: 1-3-4-2

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  48. AMVI 2019 Paper 2 (Automobile) · Q41 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    __________ torque is required to produce 500 HP at 3000 rpm

    Show answer

    Answer: 1187 N-m

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  49. AMVI 2019 Paper 2 (Automobile) · Q57 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The volumetric efficiency of the SI engine is comparatively

    Show answer

    Answer: Lower than CI engine

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  50. AMVI 2019 Paper 2 (Automobile) · Q58 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Working cycle of a 4- stroke engine is complete in

    Show answer

    Answer: Two revolution of the crankshaft

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  51. AMVI 2019 Paper 2 (Automobile) · Q66 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The end of the connecting rod is attached to the piston using

    Show answer

    Answer: Wrist pin and Piston pin

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  52. AMVI 2019 Paper 2 (Automobile) · Q80 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    For same maximum pressure and output, which of the following sequence of cycle is correct?

    Show answer

    Answer: Diesel cycle, Dual cycle, Otto cycle

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  53. AMVI 2019 Paper 2 (Automobile) · Q89 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In a four stroke SI engine --------- is compressed.

    Show answer

    Answer: Air and Fuel

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  54. AMVI 2019 Paper 2 (Automobile) · Q92 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Bad Scavenging gives

    Show answer

    Answer: Low mean indicated pressure

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  55. AMVI 2019 Paper 2 (Automobile) · Q94 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following statement is correct for Opposed piston diesel engine?

    Show answer

    Answer: Combustion chamber is located between the pistons

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  56. AMVI 2019 Paper 2 (Automobile) · Q96 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The firing order in an inline six-cylinder engine is

    Show answer

    Answer: All of the given options

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  57. AMVI 2019 Paper 2 (Automobile) · Q112 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is a method to determine the friction power of an engine?

    Show answer

    Answer: All of the given options

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  58. AMVI 2019 Paper 2 (Automobile) · Q118 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    During suction stroke, the in-cylinder pressure is

    Show answer

    Answer: < 1.013 bar

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  59. AMVI 2019 Paper 2 (Automobile) · Q123 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The brake power of an IC engine having speed 1500 rpm with torque 20 Nm is:

    Show answer

    Answer: 1000 π watts

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

Fuel Supply & Combustion

  1. AMVI 2026 Paper 2 (Automobile) · Q23 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The primary function of a pre-whirl chamber is to

    1. Increase the engine's compression ratio
    2. Create a high-velocity, swirling motion to improve fuel-air mixing
    3. Cool the incoming air charge
    4. Allow for the use of a high-pressure common-rail fuel system
    Show answer

    Answer: (2) Create a high-velocity, swirling motion to improve fuel-air mixing

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  2. AMVI 2026 Paper 2 (Automobile) · Q24 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following factors increases the ignition delay period in a CI engine ?

    1. Increased compression ratio
    2. Increased air turbulence
    3. Supercharging
    4. Lower cetane number fuel
    Show answer

    Answer: (4) Lower cetane number fuel

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  3. AMVI 2026 Paper 2 (Automobile) · Q25 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following factors can increase the tendency of knocking in a Compression Ignition (CI) engine ?

    1. A longer ignition delay period
    2. Using a fuel with a higher cetane number
    3. A lower compression ratio
    4. A lower temperature of the unburnt fuel-air mixture
    Show answer

    Answer: (1) A longer ignition delay period

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  4. AMVI 2026 Paper 2 (Automobile) · Q31 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which type of injection is considered the most accurate ?

    1. Throttle body injection
    2. Manifold injection
    3. Direct injection
    4. Port injection
    Show answer

    Answer: (3) Direct injection

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  5. AMVI 2026 Paper 2 (Automobile) · Q32 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    What is the purpose of the venturi in a carburetor ?

    1. To increase the fuel flow
    2. To decrease the pressure and draw fuel into the airstream
    3. To regulate the amount of air entering the engine
    4. To provide a consistent air-fuel ratio
    Show answer

    Answer: (2) To decrease the pressure and draw fuel into the airstream

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  6. AMVI 2026 Paper 2 (Automobile) · Q33 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    What is the purpose of internal baffles inside a fuel tank ?

    1. To increase the tank's volume
    2. To reduce fuel sloshing during movement
    3. To allow for easier fuel delivery
    4. To help the fuel pump run cooler
    Show answer

    Answer: (2) To reduce fuel sloshing during movement

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  7. AMVI 2026 Paper 2 (Automobile) · Q97 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    In a C.I. engine squish is created

    1. towards end of compression stroke
    2. at the end of suction stroke
    3. at the beginning of suction stroke
    4. during combustion
    Show answer

    Answer: (1) towards end of compression stroke

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  8. AMVI 2026 Paper 2 (Automobile) · Q98 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Detonation in S.I. engines occurs due to

    1. Preignition of charge before the spark
    2. Sudden ignition of charge before the spark
    3. Autoignition of the charge after the spark is struck
    4. Non availability of fuel
    Show answer

    Answer: (3) Autoignition of the charge after the spark is struck

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  9. AMVI 2026 Paper 2 (Automobile) · Q101 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    In C.I. engines knocking tendency increases with

    1. Increases in compression ratio
    2. Increasing inlet temperature of air
    3. Decrease in compression ratio
    4. Increasing the coolant temperature
    Show answer

    Answer: (3) Decrease in compression ratio

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  10. AMVI 2026 Paper 2 (Automobile) · Q102 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    In C.I. engines with increase in compression ratio the delay period

    1. Increases
    2. Decreases
    3. First increases and then decreases
    4. Remains unaffected
    Show answer

    Answer: (2) Decreases

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  11. AMVI 2026 Paper 2 (Automobile) · Q106 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The venturi in carburetor results in

    1. Decrease in air velocity
    2. Increase in air velocity
    3. Decrease in fuel flow
    4. Increase in manifold vacuum
    Show answer

    Answer: (2) Increase in air velocity

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  12. AMVI 2026 Paper 2 (Automobile) · Q107 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Precise petrol injection system is

    1. Direct injection
    2. Sequential injection
    3. Throttle body injection
    4. Port injection
    Show answer

    Answer: (3) Throttle body injection

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  13. AMVI 2026 Paper 2 (Automobile) · Q108 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The fuel injection pressure in solid injection system is around

    1. Less than 10 bar
    2. 10 – 20 bar
    3. 30 – 50 bar
    4. 200 – 250 bar
    Show answer

    Answer: (4) 200 – 250 bar

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  14. AMVI 2026 Paper 2 (Automobile) · Q109 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    ________ regulates the pressure strokes in the fuel injection pump of a diesel engine.

    1. Pump shaft
    2. Control rack
    3. Lift of plunger
    4. Needle valve
    Show answer

    Answer: (2) Control rack

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  15. AMVI 2023 Paper 2 (Automobile) · Q24 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Match the following circuits of carburettor with their individual functions correctly.

    List IList II
    (A) Main circuit(i) Provides just enough fuel for fuel-efficient cruising
    (B) Idle circuit(ii) Provides just enough fuel to keep the engine idling
    (C) Power enrichment circuit(iii) Provides extra fuel when the car is going up a hill or towing a trailer
    (D) Choke(iv) Provides extra fuel when the engine is cold so that it will start
    1. (A)-(i), (B)-(ii), (C)-(iii) and (D)-(iv)
    2. (A)-(ii), (B)-(iii), (C)-(i) and (D)-(iv)
    3. (A)-(iv), (B)-(iii), (C)-(ii) and (D)-(i)
    4. (A)-(ii), (B)-(iii), (C)-(iv) and (D)-(i)
    Show answer

    Answer: (1) (A)-(i), (B)-(ii), (C)-(iii) and (D)-(iv)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  16. AMVI 2023 Paper 2 (Automobile) · Q33 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following types of combustion chambers is NOT used in the spark ignition engine?

    1. T-head type chamber
    2. L-head chamber
    3. I-head type chamber
    4. Shallow depth chamber
    Show answer

    Answer: (4) Shallow depth chamber

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  17. AMVI 2023 Paper 2 (Automobile) · Q34 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which combustion chamber is shown in the figure, and in which type of engine is it used?

    Figure for question 34
    1. Cylindrical chamber used in compression ignition engine
    2. Semi-spherical chamber used in spark ignition engine
    3. Toroidal chamber used in compression ignition engine
    4. Shallow depth combustion chamber used in spark ignition chamber
    Show answer

    Answer: (1) Cylindrical chamber used in compression ignition engine

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  18. AMVI 2023 Paper 2 (Automobile) · Q35 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following types of combustion chambers is shown in the figure?

    Figure for question 35
    1. Swirl combustion chamber
    2. Shallow chamber
    3. F-head type chamber
    4. T-head type chamber
    Show answer

    Answer: (1) Swirl combustion chamber

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  19. AMVI 2023 Paper 2 (Automobile) · Q36 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following operating variables is NOT affected due to ignition delay during compression ignition combustion?

    1. Injection pressure
    2. Compression temperature
    3. Air velocity in combustion chambers
    4. Suction air temperature
    Show answer

    Answer: (4) Suction air temperature

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  20. AMVI 2023 Paper 2 (Automobile) · Q37 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The phenomenon of excessive turbulence increases combustion rapidly and leads to ________.

    1. high power generation
    2. low flame velocity
    3. detonation
    4. incomplete combustion
    Show answer

    Answer: (3) detonation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  21. AMVI 2023 Paper 2 (Automobile) · Q38 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The process of preparing a combustible fuel-air mixture outside the engine cylinder is known as:

    1. Knocking
    2. Vaporisation
    3. Carburation
    4. Compression
    Show answer

    Answer: (3) Carburation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  22. AMVI 2023 Paper 2 (Automobile) · Q83 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which ofthe givenstatements are correct? 1. In the SI engines, detonation occurs near the end of combustion; whereas in CI engines, knocking occurs near the beginning of combustion. 2. In SI engines, no problems are encountered on account of pre-ignition. 3. Low inlet pressure and temperature reduce knocking tendency in SI engines but increase the knocking tendency in CI engines.

    1. 1, 2 and 3
    2. Only 1 and 2
    3. Only 2 and 3
    4. Only 1 and 3
    Show answer

    Answer: (4) Only 1 and 3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  23. AMVI 2023 Paper 2 (Automobile) · Q97 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    ______ is typically sucked into the cylinder during the suction stroke in the fuel supply system.

    1. Diesel
    2. Air
    3. Water
    4. Oil
    Show answer

    Answer: (2) Air

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  24. AMVI 2023 Paper 2 (Automobile) · Q99 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following components of the engine system cleans the air before it enters the cylinder of the engine?

    1. Crank
    2. Piston ring
    3. Filter
    4. Spark plug
    Show answer

    Answer: (3) Filter

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  25. AMVI 2023 Paper 2 (Automobile) · Q100 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    ______ atomizes the fuel and mixes it with air in an I.C. engine.

    1. Camshaft
    2. Spark plug
    3. Piston
    4. Carburetor
    Show answer

    Answer: (4) Carburetor

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  26. AMVI 2023 Paper 2 (Automobile) · Q101 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    What condition does the engine require while idling in a spark ignition (SI) engine?

    1. Maximum power output
    2. Heavy load demand
    3. Overheating
    4. No power demand
    Show answer

    Answer: (4) No power demand

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  27. AMVI 2023 Paper 2 (Automobile) · Q102 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    When all the air supplied is fully utilized, a spark ignition (SI) engine produce ______?

    1. minimum power
    2. maximum power
    3. no power
    4. average power
    Show answer

    Answer: (2) maximum power

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  28. AMVI 2019 Paper 2 (Automobile) · Q6 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    One kg of hydrogen requires __________ kg of oxygen to produce ---- kg water.

    Show answer

    Answer: 8,9

    The combustion equation is 2H₂ + O₂ → 2H₂O. By mass, 4 kg of hydrogen combines with 32 kg of oxygen to form 36 kg of water. Dividing by 4, 1 kg of hydrogen needs 8 kg of oxygen and produces 9 kg of water. This 9 kg per kg figure is used to find the water in the products when working out the higher and lower calorific values of a fuel.

  29. AMVI 2019 Paper 2 (Automobile) · Q12 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following is an advantage of a compression swirl?

    Show answer

    Answer: All of the given options

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  30. AMVI 2019 Paper 2 (Automobile) · Q13 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    In a 4- stroke compression ignition (CI), the fuel is injected about

    Show answer

    Answer: 15° before top dead centre

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  31. AMVI 2019 Paper 2 (Automobile) · Q15 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    In S.I. engine, Raising the coolant temperature__________

    Show answer

    Answer: Decreases delay period

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  32. AMVI 2019 Paper 2 (Automobile) · Q18 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    __________ is not an integral part of a carburettor

    Show answer

    Answer: Fuel Pump

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  33. AMVI 2019 Paper 2 (Automobile) · Q44 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    __________ (TBFI) are a substitution of electromechanical replacement for the carburettor

    Show answer

    Answer: Throttle Body Fuel Injector

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  34. AMVI 2019 Paper 2 (Automobile) · Q59 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Stoichiometric fuel- air ratio of a gasoline is

    Show answer

    Answer: 1: 15

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  35. AMVI 2019 Paper 2 (Automobile) · Q65 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Carburettor is commonly used in

    Show answer

    Answer: Spark Ignition (S.I.)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  36. AMVI 2019 Paper 2 (Automobile) · Q90 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Incomplete combustion is a result of?

    Show answer

    Answer: Cool metal surfaces of the combustion chamber and Imperfect mixture ratio

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  37. AMVI 2019 Paper 2 (Automobile) · Q95 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The delay period in petrol engine is __________ compared to diesel engine

    Show answer

    Answer: Long

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  38. AMVI 2019 Paper 2 (Automobile) · Q110 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The path taken by the petrol is

    Show answer

    Answer: Fuel tank- Float Chamber-Jets- Throat

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  39. AMVI 2019 Paper 2 (Automobile) · Q115 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Relative fuel air ratio is?

    Show answer

    Answer: Actual F/A to Stoichiometric F/A

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  40. AMVI 2019 Paper 2 (Automobile) · Q119 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Choke is used to provide

    Show answer

    Answer: Rich mixture during idling condition

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  41. AMVI 2019 Paper 2 (Automobile) · Q128 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following is a component of a Fuel supply system of diesel engine?

    Show answer

    Answer: All of the given options

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  42. AMVI 2019 Paper 2 (Automobile) · Q135 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The type of fuel injection system in which fuel is injected at each intake port

    Show answer

    Answer: multi-point system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  43. AMVI 2019 Paper 2 (Automobile) · Q143 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Increase in jacket water temperature __________ the delay period

    Show answer

    Answer: Decreases

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

Cooling & Lubrication

  1. AMVI 2026 Paper 2 (Automobile) · Q37 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which type of lubrication system is most commonly used in two-stroke engines ?

    1. Splash lubrication system
    2. Wet sump lubrication system
    3. Pressure lubrication system
    4. Mist lubrication system
    Show answer

    Answer: (4) Mist lubrication system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  2. AMVI 2026 Paper 2 (Automobile) · Q38 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which of the following is a component of a pressure lubrication system ?

    1. Scoop on the connecting rod
    2. Oil mixed with fuel
    3. Oil pump that forces oil through channels
    4. Oil splashed onto components from a reservoir
    Show answer

    Answer: (3) Oil pump that forces oil through channels

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  3. AMVI 2026 Paper 2 (Automobile) · Q39 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which of the following is a key advantage of the liquid cooling system ?

    1. It is very cheap
    2. It provides even cooling throughout the engine
    3. It is dependent only on the supply of water
    4. It absorbs a considerable amount of power from the engine
    Show answer

    Answer: (2) It provides even cooling throughout the engine

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  4. AMVI 2026 Paper 2 (Automobile) · Q40 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    In an air-cooled engine, what component helps to increase the surface area for heat dissipation ?

    1. Radiator fan
    2. Pressure cap
    3. Extended fins
    4. Circulating air
    Show answer

    Answer: (3) Extended fins

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  5. AMVI 2026 Paper 2 (Automobile) · Q113 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Friction that occurs between the layers of oil film is called

    1. Viscous friction
    2. Greasy friction
    3. Dry friction
    4. Boundary friction
    Show answer

    Answer: (1) Viscous friction

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  6. AMVI 2026 Paper 2 (Automobile) · Q114 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    The main purpose of thermostat in an engine cooling system is to

    1. Allow the engine to warm quickly
    2. Prevent the coolant from boiling
    3. Pressurise the system
    4. Indicate to the driver the coolant temperature
    Show answer

    Answer: (1) Allow the engine to warm quickly

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  7. AMVI 2023 Paper 2 (Automobile) · Q54 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    The part of a lubrication system in piston engine whereby the crankcase sump is used as an integral oil reservoir is known as:

    1. dry sump reservoir
    2. dual lubrication sump reservoir
    3. wet sump reservoir
    4. cylinder case sump reservoir
    Show answer

    Answer: (3) wet sump reservoir

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  8. AMVI 2023 Paper 2 (Automobile) · Q55 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    In which of the following types of engines is petroil lubrication system employed?

    1. Four-stroke diesel engine
    2. Four-stroke petrol engine
    3. Steam engine
    4. Two-stroke engines
    Show answer

    Answer: (4) Two-stroke engines

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  9. AMVI 2023 Paper 2 (Automobile) · Q56 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which of the following types of lubrication systems is shown in the figure?

    Figure for question 56
    1. Petroil lubrication system
    2. Pressure lubrication system
    3. Pump lubrication system
    4. Dry lubrication system
    Show answer

    Answer: (2) Pressure lubrication system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  10. AMVI 2023 Paper 2 (Automobile) · Q57 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    The metal fins on the internal combustion engine's cylinder head as shown in the figure are used for which of the following purposes?

    Figure for question 57
    1. To heat the air during suction stroke
    2. To dissipate the exhaust gases during exhaust stroke
    3. To increase heat dissipation rate of the cylinder head by air cooling
    4. To increase the heat dissipation rate of the cylinder head by water cooling
    Show answer

    Answer: (3) To increase heat dissipation rate of the cylinder head by air cooling

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  11. AMVI 2023 Paper 2 (Automobile) · Q58 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which of the following types of internal combustion cooling system is shown in the figure?

    Figure for question 58
    1. Air syphon cooling system
    2. Gravitational water cooling system
    3. Buoyant syphon water cooling system
    4. Thermo-syphon water cooling system
    Show answer

    Answer: (4) Thermo-syphon water cooling system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  12. AMVI 2023 Paper 2 (Automobile) · Q91 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    The air cooling system helps to dissipate the heat from which of the following parts?

    1. Engine piston
    2. Engine crank shaft
    3. Exhaust pipe
    4. Cylinder and head fins
    Show answer

    Answer: (4) Cylinder and head fins

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  13. AMVI 2023 Paper 2 (Automobile) · Q95 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    The pressure feed lubrication system does NOT lubricate which of the following parts?

    1. Timing gears
    2. Valve rods and push rods
    3. Rocker arms
    4. Main bearings of crankshaft
    Show answer

    Answer: (2) Valve rods and push rods

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  14. AMVI 2019 Paper 2 (Automobile) · Q113 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which of the following is an important function of a lubrication system?

    Show answer

    Answer: All of the given options

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  15. AMVI 2019 Paper 2 (Automobile) · Q126 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    In engine __________ requires lubrication

    Show answer

    Answer: All of the given options

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  16. AMVI 2019 Paper 2 (Automobile) · Q127 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Methods of Water Cooling is

    Show answer

    Answer: All of the given options

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

Fuels, Lubricants & Emissions

  1. AMVI 2026 Paper 2 (Automobile) · Q18 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which statement correctly compares flash point and fire point ?

    1. The fire point is always lower than the flash point.
    2. The flash point and fire point are the same temperature.
    3. The fire point is typically higher than the flash point.
    4. The flash point is higher than fire point.
    Show answer

    Answer: (3) The fire point is typically higher than the flash point.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  2. AMVI 2026 Paper 2 (Automobile) · Q19 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following fuels has the highest calorific value ?

    1. Wood
    2. Coal
    3. LPG
    4. Petrol
    Show answer

    Answer: (3) LPG

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  3. AMVI 2026 Paper 2 (Automobile) · Q21 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following is the chemical that is used as the reference standard for a Cetane number of 100 ?

    1. Heptane
    2. Octane
    3. Hexadecane (Cetane)
    4. Naphthalene
    Show answer

    Answer: (3) Hexadecane (Cetane)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  4. AMVI 2026 Paper 2 (Automobile) · Q60 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What is the impact of high concentrations of pollutants like sulfur dioxide on the environment ?

    1. Causes a cooling effect in the atmosphere
    2. Is the primary cause of acid rain
    3. Do not cause the formation of smog
    4. Neutralizes acid in water bodies
    Show answer

    Answer: (2) Is the primary cause of acid rain

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  5. AMVI 2026 Paper 2 (Automobile) · Q61 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What is a major exhaust emission from CI (diesel) engines compared to SI (petrol) engines ?

    1. Carbon Monoxide (CO)
    2. Particulates
    3. Sulphur
    4. Unburnt Hydrocarbons (HC)
    Show answer

    Answer: (2) Particulates

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  6. AMVI 2026 Paper 2 (Automobile) · Q62 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following factors increases the tendency for NOₓ formation in an SI engine ?

    1. Decreasing the air-fuel ratio
    2. Increasing the peak combustion temperature
    3. Increasing the ignition delay
    4. Lowering the engine’s compression ratio
    Show answer

    Answer: (2) Increasing the peak combustion temperature

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  7. AMVI 2026 Paper 2 (Automobile) · Q63 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Odor emissions from diesel engines are mainly caused by

    1. Oxides of nitrogen (NOₓ)
    2. Carbon monoxide (CO)
    3. Particulate matter (soot)
    4. Unburnt or partially burnt hydrocarbons, including aldehydes
    Show answer

    Answer: (4) Unburnt or partially burnt hydrocarbons, including aldehydes

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  8. AMVI 2026 Paper 2 (Automobile) · Q64 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Aldehydes in diesel engine exhaust are a type of

    1. Sulfur oxide compound
    2. Particulate matter
    3. Unburnt hydrocarbon (HC)
    4. Inert gas
    Show answer

    Answer: (3) Unburnt hydrocarbon (HC)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  9. AMVI 2026 Paper 2 (Automobile) · Q65 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following operating conditions is a primary cause for high NOₓ emissions in a diesel engine ?

    1. Low combustion temperature
    2. Insufficient oxygen supply
    3. High combustion pressure and temperature with sufficient reaction time
    4. Delayed injection timing
    Show answer

    Answer: (3) High combustion pressure and temperature with sufficient reaction time

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  10. AMVI 2026 Paper 2 (Automobile) · Q66 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Diesel engine exhaust primarily contains which forms of nitrogen oxides ?

    1. N₂O and NO₂
    2. N₂O₄ and N₂O₃
    3. Pure N₂ and O₂
    4. NO and NO₂
    Show answer

    Answer: (4) NO and NO₂

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  11. AMVI 2026 Paper 2 (Automobile) · Q89 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Flash point and fire point are characteristics primarily related to the

    1. Low-temperature behaviour of the fuel
    2. High-temperature behaviour and volatility of the fuel
    3. Purity of the fuel
    4. Viscosity of the fuel
    Show answer

    Answer: (2) High-temperature behaviour and volatility of the fuel

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  12. AMVI 2026 Paper 2 (Automobile) · Q90 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    The fire point of a fuel is the lowest temperature at which its vapor will continue to burn for at least how many seconds after ignition ?

    1. 1 second
    2. 2 seconds
    3. 4 seconds
    4. 5 seconds
    Show answer

    Answer: (4) 5 seconds

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  13. AMVI 2026 Paper 2 (Automobile) · Q99 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    The ratings of C.I. engine fuel is given by

    1. Octane Number
    2. Performance Number
    3. Cetane Number
    4. Bearing Number
    Show answer

    Answer: (3) Cetane Number

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  14. AMVI 2026 Paper 2 (Automobile) · Q100 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Bomb Calorimeter is used to find the calorific value of ________ fuel.

    1. Solid
    2. Gaseous
    3. Solid and gaseous
    4. Nuclear
    Show answer

    Answer: (3) Solid and gaseous

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  15. AMVI 2026 Paper 2 (Automobile) · Q112 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Detergents are oil additives used to

    1. Reduce viscosity
    2. Increase fire point
    3. Prevent sludge formation
    4. Prevent foaming
    Show answer

    Answer: (3) Prevent sludge formation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  16. AMVI 2026 Paper 2 (Automobile) · Q141 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Carbon Monoxide emission from S.I. engine are higher when the engine is

    1. Idling
    2. Cruising
    3. Accelerating
    4. Decelerating
    Show answer

    Answer: (1) Idling

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  17. AMVI 2026 Paper 2 (Automobile) · Q142 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Orsat flue gas analysis gives

    1. Mass analysis of wet products of combustion
    2. Volumetric analysis of dry products of combustion
    3. Mass analysis of dry products of combustion
    4. Volumetric analysis of wet products of combustion
    Show answer

    Answer: (2) Volumetric analysis of dry products of combustion

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  18. AMVI 2026 Paper 2 (Automobile) · Q143 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Flame Ionisation Detector is used for measuring

    1. CO
    2. HC
    3. NOₓ
    4. CO₂
    Show answer

    Answer: (2) HC

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  19. AMVI 2026 Paper 2 (Automobile) · Q144 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Chemiluminescence technique is used to measure

    1. NOₓ
    2. CO
    3. CO₂
    4. Smoke intensity
    Show answer

    Answer: (1) NOₓ

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  20. AMVI 2026 Paper 2 (Automobile) · Q145 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Non-dispersive infra-red analyser is widely accepted instrument for measuring

    1. NOₓ
    2. HC
    3. CO
    4. CO₂
    Show answer

    Answer: (3) CO

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  21. AMVI 2023 Paper 2 (Automobile) · Q3 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Match the following points with their definitions.

    List IList II
    (A) Flash point(i) The lowest temperature at which the vapours of volatile materials ignite when an ignition source is provided
    (B) Fire point(ii) The lowest temperature at which the vapour of fuel can continue to burn for at least five seconds after the ignition has started
    C) Flash point value(iii) Always lower than the fire point
    (D) Fire point value(iv) Always higher than the flash point
    1. (A)-(ii), (B)-(iv), (C)-(iii) and (D)-(i)
    2. (A)-(i), (B)-(ii), (C)-(iii) and (D)-(iv)
    3. (A)-(ii), (B)-(iv), (C)-(i) and (D)-(iii)
    4. (A)-(iii), (B)-(i), (C)-(iv) and (D)-(ii)
    Show answer

    Answer: (2) (A)-(i), (B)-(ii), (C)-(iii) and (D)-(iv)

    The flash point is the lowest temperature at which a fuel or oil gives off enough vapour to flash momentarily when a flame is applied. The fire point is the lowest temperature at which the vapour keeps burning (for at least about five seconds) after ignition. More vapour is needed for sustained burning, so the flash point is always lower than the fire point, and the fire point is always higher than the flash point.

  22. AMVI 2023 Paper 2 (Automobile) · Q92 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What is the main purpose of a lubricant?

    1. To minimise the friction
    2. To increase the friction
    3. To increase the weariness
    4. To increase the noise
    Show answer

    Answer: (1) To minimise the friction

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  23. AMVI 2023 Paper 2 (Automobile) · Q93 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Identify the INCORRECT statement related to the properties of a lubricant.

    1. It should have low viscosity.
    2. It should remain stable under changing temperatures.
    3. It should keep lubricated pans clean.
    4. It should not corrode metallic surfaces.
    Show answer

    Answer: (1) It should have low viscosity.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  24. AMVI 2023 Paper 2 (Automobile) · Q94 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Identify the multi-grade oil.

    1. SAE 10W 30
    2. SAE 25W
    3. SAE 10
    4. SAE 20W
    Show answer

    Answer: (1) SAE 10W 30

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  25. AMVI 2023 Paper 2 (Automobile) · Q104 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following statements is correct regarding the fuel properties in an automobile system? I. The volatile fuels are always preferred due to presence of constituents providing easiness in starting of engine in cold weather. II. The vaporization of fuel immediately after the engine starts is affected by the speed with which it is warmed up.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer: (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  26. AMVI 2023 Paper 2 (Automobile) · Q105 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    To get petrol from crude oil, it is primarily ______ in a refinery.

    1. filtered
    2. compressed
    3. distilled
    4. oxidized
    Show answer

    Answer: (3) distilled

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  27. AMVI 2023 Paper 2 (Automobile) · Q106 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What is the primary source of most of the petrol used in automobiles?

    1. Natural gas
    2. Coal
    3. Crude oil
    4. Biofuels
    Show answer

    Answer: (3) Crude oil

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  28. AMVI 2023 Paper 2 (Automobile) · Q107 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which method improves the antiknock qualities of the straight run gasoline by changing their molecular structure?

    1. Reforming
    2. Alkylation
    3. Cracking
    4. Polymerization
    Show answer

    Answer: (1) Reforming

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  29. AMVI 2023 Paper 2 (Automobile) · Q108 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What calorific value of fuel is necessary for efficient operation in an automobile?

    1. High calorific value
    2. Low calorific value
    3. Average calorific value
    4. Fuel power does not depend upon its calorific value
    Show answer

    Answer: (1) High calorific value

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  30. AMVI 2023 Paper 2 (Automobile) · Q109 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What are the primary components of LPG used as fuel in an automobile?

    1. Methane and ethane
    2. Hydrogen and helium
    3. Butane and propane
    4. Oxygen and nitrogen
    Show answer

    Answer: (3) Butane and propane

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  31. AMVI 2023 Paper 2 (Automobile) · Q123 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What is the most important gas produced during combustion in an automobile engine that increases the atmospheric temperature?

    1. O₂
    2. CO₂
    3. N₂
    4. SO₂
    Show answer

    Answer: (2) CO₂

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  32. AMVI 2023 Paper 2 (Automobile) · Q124 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    In the automobile engine, which two gases in the exhaust vary opposite to each other?

    1. SO₂ and O₂
    2. O₂ and CO
    3. CO₂ and CO
    4. SO₂ and N₂
    Show answer

    Answer: (3) CO₂ and CO

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  33. AMVI 2019 Paper 2 (Automobile) · Q14 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    A cetane number of C₁₀H₇CH₃is __________

    Show answer

    Answer: 0

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  34. AMVI 2019 Paper 2 (Automobile) · Q28 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    The following is the chemical formula of is o-octane

    Show answer

    Answer: C₈H₁₈

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  35. AMVI 2019 Paper 2 (Automobile) · Q37 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    The calorific value of diesel is about

    Show answer

    Answer: 42.5 MJ/kg

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  36. AMVI 2019 Paper 2 (Automobile) · Q40 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    The specific gravity of the engine lube oils varies between __________

    Show answer

    Answer: 0.85 to 0.96

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  37. AMVI 2019 Paper 2 (Automobile) · Q42 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    In a vehicle, Permeation through the walls of plastics tanks is controlled by __________

    Show answer

    Answer: All of the given options

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  38. AMVI 2019 Paper 2 (Automobile) · Q43 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Diesel NOₓ is __________ with cetane number and __________ as aromatic content is lowered

    Show answer

    Answer: increases, decreases

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  39. AMVI 2019 Paper 2 (Automobile) · Q45 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Complete a catalytic reaction: NO + CO = __________ + CO₂

    Show answer

    Answer: ½ N₂

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  40. AMVI 2019 Paper 2 (Automobile) · Q46 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following material is not used in three way catalytic converter as a catalyst?

    Show answer

    Answer: Iron

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  41. AMVI 2019 Paper 2 (Automobile) · Q47 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    __________ is used to control the particulates from a diesel engine

    Show answer

    Answer: Diesel Particulate Filter

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  42. AMVI 2019 Paper 2 (Automobile) · Q72 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Incomplete combustion is responsible for

    Show answer

    Answer: Unburned Hydrocarbon

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  43. AMVI 2019 Paper 2 (Automobile) · Q74 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following is a not a Diesel smoke?

    Show answer

    Answer: Green smoke

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  44. AMVI 2019 Paper 2 (Automobile) · Q75 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Researcher wants to decrease a NOx in SI engine then, Air fuel ratio is

    Show answer

    Answer: < 13:1 and >17:1

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  45. AMVI 2019 Paper 2 (Automobile) · Q76 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Commonly, source of pollutants from a vehicle is

    Show answer

    Answer: All of the given options

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  46. AMVI 2019 Paper 2 (Automobile) · Q77 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    The inherent oxygen content in gasoline is

    Show answer

    Answer: 0 %

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  47. AMVI 2019 Paper 2 (Automobile) · Q91 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Cloud point of a fuel is

    Show answer

    Answer: Temperature at which it solidifies

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  48. AMVI 2019 Paper 2 (Automobile) · Q93 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Viscosity of a lubrication oil is

    Show answer

    Answer: decreases with increase in temperature

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  49. AMVI 2019 Paper 2 (Automobile) · Q97 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Exhaust have 2000 ppm NOx concentration then, NOx in % is

    Show answer

    Answer: 0.2

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  50. AMVI 2019 Paper 2 (Automobile) · Q111 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    SAE stands for

    Show answer

    Answer: Society of Automotive Engineers

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  51. AMVI 2019 Paper 2 (Automobile) · Q114 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    NOₓ can be control by

    Show answer

    Answer: All of the given options

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  52. AMVI 2019 Paper 2 (Automobile) · Q116 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    EGR stands for

    Show answer

    Answer: Exhaust Gas Recirculation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  53. AMVI 2019 Paper 2 (Automobile) · Q117 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following is a function of detergent engine oil additive?

    Show answer

    Answer: Control of high temperature deposits

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  54. AMVI 2019 Paper 2 (Automobile) · Q134 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Exhaust gas products in case of complete combustion are:

    Show answer

    Answer: carbon dioxide and water

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  55. AMVI 2019 Paper 2 (Automobile) · Q136 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    At temperature higher than __________ nitrogen reacts with oxygen and forms NOₓ

    Show answer

    Answer: 1000 ⁰C

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  56. AMVI 2019 Paper 2 (Automobile) · Q137 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Measurement of exhaust emissions, just after starting the engine from cold, gives a higher than specification reading. The reason for this is:

    Show answer

    Answer: the temperature of the catalyst is low

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  57. AMVI 2019 Paper 2 (Automobile) · Q141 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    NMHC stands for

    Show answer

    Answer: Non-methane hydrocarbon

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  58. AMVI 2019 Paper 2 (Automobile) · Q142 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    General formula of olefin is

    Show answer

    Answer: CₙH₂ₙ

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.