Learn with Anil · APPSC AMVI (Assistant Motor Vehicle Inspector) PYQsPractise online →Subscribe ₹149

APPSC AMVI 2023 Paper 2 Automobile Engineering question paper with answers

APPSC Assistant Motor Vehicle Inspector 2023: Paper II (Automobile Engineering). Paper II: Automobile Engineering (diploma standard), computer-based test, 150 questions, 300 marks, 150 minutes, in English. Notification 12/2022 (Suppl. 08/2023) · CBT, held on 6 October 2023. All four options with the answer from APPSC's final key, plus a short explanation for every question (the first 10 here, all of them in the app).

ఏపీపీఎస్సీ అసిస్టెంట్ మోటార్ వెహికల్ ఇన్‌స్పెక్టర్ (AMVI) పేపర్-2 ఆటోమొబైల్ ఇంజనీరింగ్ 2023 ప్రశ్నపత్రం సమాధానాలతో

Attempt this paper · 148 min timerMake a topic-wise quiz

The correct answer to every question is free on this page, and so are the explanations of the first 10. For all 148 explanations, practise the paper in the app with the ₹149 All-in-One Pass, one payment for every exam on the site.

Subjects in this paper

All 148 questions

  1. Q1 · Thermodynamics & Heat Transfer · Refrigeration & Air Conditioning

    Which of the following is NOT a part of the air conditioning system used in cars?

    1. Compressor
    2. Refrigerant
    3. Turbo charger
    4. Condenser
    Show answer

    Answer: (3) Turbo charger

    A car air-conditioning system is a vapour-compression refrigeration circuit: the compressor (belt- or motor-driven), condenser, receiver-drier, expansion valve or orifice tube and evaporator, with a refrigerant such as R-134a or R-1234yf circulating through them. A turbocharger is an exhaust-driven turbine and compressor that boosts intake air pressure to raise engine power; it is part of the air-induction system, not the air conditioner.

  2. Q2 · Thermodynamics & Heat Transfer · Refrigeration & Air Conditioning

    Select the option that is true regarding the following two statements labelled Assertion (A) and Reason (R). Assertion (A): The COP of an air-conditioning plant is lower than that of an ice plant. Reason (R): The temperatures required in the ice plant are lower than those required for an air-conditioning plant.

    1. Both A and R are individually true, and R is the correct explanation of A.
    2. Both A and R are individually true, but R is not the correct explanation of A.
    3. A is true, but R is false.
    4. A is false, but R is true.
    Show answer

    Answer: (4) A is false, but R is true.

    COP falls as the evaporator temperature falls, because the compressor has to lift heat through a larger temperature difference (Carnot COP = T_L/(T_H − T_L)). An ice plant evaporates below 0 °C, while an air-conditioning plant evaporates at about 5–10 °C, so R is true. For example, with a 45 °C condenser the Carnot COP is about 7.0 at 5 °C but only 4.3 at −15 °C. Hence an air-conditioning plant has the higher COP and A is false.

  3. Q3 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Match the following points with their definitions.

    List IList II
    (A) Flash point(i) The lowest temperature at which the vapours of volatile materials ignite when an ignition source is provided
    (B) Fire point(ii) The lowest temperature at which the vapour of fuel can continue to burn for at least five seconds after the ignition has started
    C) Flash point value(iii) Always lower than the fire point
    (D) Fire point value(iv) Always higher than the flash point
    1. (A)-(ii), (B)-(iv), (C)-(iii) and (D)-(i)
    2. (A)-(i), (B)-(ii), (C)-(iii) and (D)-(iv)
    3. (A)-(ii), (B)-(iv), (C)-(i) and (D)-(iii)
    4. (A)-(iii), (B)-(i), (C)-(iv) and (D)-(ii)
    Show answer

    Answer: (2) (A)-(i), (B)-(ii), (C)-(iii) and (D)-(iv)

    The flash point is the lowest temperature at which a fuel or oil gives off enough vapour to flash momentarily when a flame is applied. The fire point is the lowest temperature at which the vapour keeps burning (for at least about five seconds) after ignition. More vapour is needed for sustained burning, so the flash point is always lower than the fire point, and the fire point is always higher than the flash point.

  4. Q4 · Engineering Mechanics & Machine Design · Machine Design

    Read the given statement and conclusions carefully and select the correct option. Statement: Self-locking screw jack means when the rotational force on the screw is removed, it will remain motionless and will not rotate backwards. Conclusions: I. Self-locking screw jacks are safer compared to hydraulic jack which is not self-locking. II. Single start trapezoidal type screws are typically self-locking. III. All screw jacks with double start lifting screws are also considered self-locking.

    1. Statement and all the conclusions I, II and III are true.
    2. Statement is incorrect, but conclusions I and II are true.
    3. Statement is true, but conclusions I, II and III are false.
    4. Only statement and conclusions I and II are true.
    Show answer

    Answer: (4) Only statement and conclusions I and II are true.

    A screw is self-locking when the friction angle is at least equal to the helix (lead) angle, so the load cannot turn it back once the effort is removed; the statement is true. Single-start square or trapezoidal screws have a small lead angle and are normally self-locking, which makes such jacks safe to leave under load (I and II). A double-start screw has twice the lead and a larger helix angle, so it is often not self-locking; III is false.

  5. Q5 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Match the following four internally reversible processes used in a four-stroke Otto cycle as shown in figure.

    List IList II
    (A) Isentropic compression(i) 2-3
    (B) Constant-volume heat addition(ii) 1-2
    (C) Isentropic expansion(iii) 4-1
    (D) Constant-volume heat rejection(iv) 3-4
    Figure for question 5
    1. (A)-(i), (B)-(ii), (C)-(iii) and (D)-(iv)
    2. (A)-(iv), (B)-(iii), (C)-(ii) and (D)-(i)
    3. (A)-(ii), (B)-(i), (C)-(iv) and (D)-(iii)
    4. (A)-(ii), (B)-(iv), (C)-(i) and (D)-(iii)
    Show answer

    Answer: (3) (A)-(ii), (B)-(i), (C)-(iv) and (D)-(iii)

    On the P–V diagram of the air-standard Otto cycle, 1–2 is isentropic (constant-entropy) compression as the volume falls, 2–3 is heat addition at constant volume (vertical rise in pressure), 3–4 is isentropic expansion (power stroke), and 4–1 is heat rejection at constant volume (vertical drop in pressure). So A–(ii), B–(i), C–(iv) and D–(iii).

  6. Q7 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Select the option that is true regarding the following two statements labelled Assertion (A) and Reason (R). Assertion (A): The C.I. engine is found to be more efficient than the S.I. engine. Reason (R): Modern C.I. engines operate on a dual-cycle, which has efficiency greater than the Otto cycle.

    1. Both A and R are individually true, and R is the correct explanation of A.
    2. Both A and R are individually true, but R is not the correct explanation of A.
    3. A is true, but R is false.
    4. A is false, but R is true.
    Show answer

    Answer: (2) Both A and R are individually true, but R is not the correct explanation of A.

    C.I. engines are more efficient mainly because they run at much higher compression ratios (about 14–22 against 8–12 for S.I. engines), with lean mixtures and no throttling losses. Modern high-speed C.I. engines are modelled by the dual (limited-pressure) cycle, which is more efficient than the Otto cycle when both work to the same peak pressure; for the same compression ratio, however, the Otto cycle is the most efficient. So R holds only for the same peak pressure; the real reason for A is the higher compression ratio, and R does not explain A.

  7. Q8 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Match the following air standard cycles with their working fluids

    List IList II
    (A) Air standard cycle(i) A mixture of air and fuel is a working fluid
    (B) Actual cycle(ii) Generation of energy by burning of fuel with air
    (iii) Air is working fluid
    (iv) No internal heat generation
    (v) This cycle is completely closed
    (vi) Energy is generated inside of the engine
    1. (A)-(iii), (iv) and (v); (B)-(i), (ii) and (vi)
    2. (A)-(i), (ii) and (vi); (B)-(iii), (iv) and (v)
    3. (A)-(ii), (i) and (iv); (B)-(iii), (v) and (vi)
    4. (A)-(i), (ii) and (iii); (B)-(iv), (v) and (vi)
    Show answer

    Answer: (1) (A)-(iii), (iv) and (v); (B)-(i), (ii) and (vi)

    The air-standard cycle is an idealisation: the working fluid is air alone, treated as a perfect gas, heat is added from an external source instead of by combustion (no internal heat generation), and the same air is recirculated in a closed cycle. In the actual engine cycle the working fluid is an air–fuel mixture, energy is released by burning the fuel with air, and this happens inside the engine cylinder.

  8. Q9 · Automobile Chassis & Transmission · Wheels & Tyres

    Which of the following statements is INCORRECT about wire wheels?

    1. This type of wheel can be used for tubed tyres only.
    2. This type of wheel is used in racing cars only now a days.
    3. Heat dissipation takes place to the surroundings by means of spokes fitted in the rim.
    4. Tubeless tyres cannot be fitted over wire wheels.
    Show answer

    Answer: (2) This type of wheel is used in racing cars only now a days.

    Wire (spoke) wheels have a hub joined to the rim by tensioned steel spokes. They are light and let air circulate past the hub and brake drum, aiding cooling, but the spoke nipples pierce the rim, so conventional wire wheels need tubed tyres. They are not confined to racing cars today: they are widely used on motorcycles and bicycles and on some vintage and sports cars, so statement (2) is the incorrect one.

  9. Q10 · Automobile Chassis & Transmission · Wheels & Tyres

    Which of the following symptoms is NOT due to low tyre pressure in a vehicle?

    1. Increase in rolling resistance
    2. Increased fuel consumption due to rolling resistance, which makes the engine work harder
    3. Uneven tread wear - the edges of the tyre wear out faster
    4. Smaller contact area with the road
    Show answer

    Answer: (4) Smaller contact area with the road

    An under-inflated tyre flexes more and flattens out, so its contact patch with the road becomes larger, not smaller. The extra flexing raises rolling resistance and heat build-up, which increases fuel consumption, and the load is carried on the shoulders, so both edges of the tread wear faster than the centre. A smaller contact patch with centre wear is a symptom of over-inflation.

  10. Q11 · Automobile Chassis & Transmission · Steering & Suspension

    Select the option that is true regarding the following two statements labelled Assertion (A) and Reason (R). Assertion (A): Caster angle is concerned with mending the angular proportions between the wheels’ vertical axis and the vertical axis of the car when viewed from the front. Reason (R): This is concerned with maintaining stability and balance while steering the car. The mechanic tends to find the fine balance between positive caster angle and negative caster angle to correct misalignment.

    1. Both A and R are individually true, and R is the correct explanation of A.
    2. Both A and R are individually true, but R is not the correct explanation of A.
    3. A is true, but R is false.
    4. A is false, but R is true.
    Show answer

    Answer: (4) A is false, but R is true.

    The tilt of the wheel from the vertical seen from the front of the car is camber, not caster, so A is false. Caster is the forward or backward tilt of the steering (kingpin) axis seen from the side. It provides directional stability and the self-centring of the steering after a turn, and adjusting caster to the correct positive or negative value is part of wheel alignment, which is what R describes.

  11. Q12 · Automobile Chassis & Transmission · Steering & Suspension

    Select the option that is true regarding the following two statements labelled Assertion (A) and Reason (R). Assertion (A): Toe is the alignment of the tyres in relation to being parallel to each other when viewed from directly above the vehicle. Tyres could face in (toe-in) or outwards (toe-out). Reason (R): Tires are ‘feathered’ when the tread is smooth on one side and sharp on the other. This is usually a sign of poor toe alignment.

    1. Both A and R are individually true, and R is the correct explanation of A.
    2. Both A and R are individually true, but R is not the correct explanation of A.
    3. A is true, but R is false.
    4. A is false, but R is true.
    Show answer

    Answer: (2) Both A and R are individually true, but R is not the correct explanation of A.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  12. Q13 · Thermodynamics & Heat Transfer · Thermodynamics

    Match the following thermodynamic systems with their properties.

    List IList II
    (A) Open system(i) The system which can exchange only energy but not mass with surroundings
    (B) Closed system(ii) The system in which neither energy nor matter can be exchanged with surroundings
    (C) Isolated system(iii) The system which can exchange both matter and energy with surroundings
    1. (A)-(i), (B)-(ii) and (C)-(iii)
    2. (A)-(iii), (B)-(ii) and (C)-(i)
    3. (A)-(iii), (B)-(i) and (C)-(ii)
    4. (A)-(ii), (B)-(i) and (C)-(iii)
    Show answer

    Answer: (3) (A)-(iii), (B)-(i) and (C)-(ii)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  13. Q14 · Thermodynamics & Heat Transfer · Thermodynamics

    Read the given statement and conclusions carefully and select the correct option. Statement (A): If there is no tendency to change the microscopic properties or inner properties of the system even when the system is isolated from surroundings, then it is considered the thermodynamic equilibrium. Conclusion: I. When any unbalanced force is absent in the system, then it is called chemical equilibrium. II. Thermal equilibrium means there is no change of any property of the system. III. If a system can undergo a chemical reaction, then it is called a chemically equilibrium system.

    1. Statement A is correct, but conclusions I, II and III are not true explanations of A.
    2. Statement A and conclusions I, II and III are individually true.
    3. Only statement A and conclusion II are true.
    4. Statement A is correct, and conclusions I, II and III are true explanations of A.
    Show answer

    Answer: (3) Only statement A and conclusion II are true.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  14. Q15 · Thermodynamics & Heat Transfer · Thermodynamics

    Select the option that is true regarding the following two statements labelled Assertion (A) and Reason (R). Assertion (A): Zeroth Law of Thermodynamics states that when two bodies are in thermal equilibrium with another third body, then the two bodies are also in thermal equilibrium with each other. Reason (R): If we take three bodies A, B and C, then if A and B are in thermal equilibrium and B and C are in thermal equilibrium separately, then A and C are also considered to be in thermal equilibrium.

    1. Both A and R are individually true, and R is the correct explanation of A.
    2. Both A and R are individually true, but R is not the correct explanation of A.
    3. A is true, but R is false.
    4. A is false, but R is true.
    Show answer

    Answer: (1) Both A and R are individually true, and R is the correct explanation of A.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  15. Q16 · Thermodynamics & Heat Transfer · Thermodynamics

    Match the following laws with their correct explanation.

    List IList II
    A) First law of thermodynamic system(i) It says that heat always moves from hotter objects to colder ones.
    (B) Second law of thermodynamic system(ii) It states that at absolute zero temperature of a system, the entropy becomes constant.
    (C) Zeroth law of thermodynamic system(iii) It states that energy cannot be created or destroyed, only converted from one form to another.
    (D) Third law of thermodynamic system(iv) If two systems are in thermal equilibrium with a third system, they must be in thermal equilibrium with each other.
    1. (A)-(i), (B)-(ii), (C)-(iii) and (D)-(iv)
    2. (A)-(iii), (B)-(i), (C)-(iv) and (D)-(ii)
    3. (A)-(ii), (B)-(iii), (C)-(i) and (D)-(iv)
    4. (A)-(iv), (B)-(iii), (C)-(ii) and (D)-(i)
    Show answer

    Answer: (2) (A)-(iii), (B)-(i), (C)-(iv) and (D)-(ii)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  16. Q17 · Thermodynamics & Heat Transfer · Thermodynamics

    Read the given statement and conclusions carefully and select the correct option. Statement (A): The Mollier diagram is a tool used by engineers to predict, theoretically, the performance of systems and installations. Conclusions: I. The Mollier diagram is also called the enthalpy (h)–entropy (s) chart. II. Typically, the Mollier chart covers pressure in the range of 1.0 to 10 bar and up to 100°C temperature and plotted for only water.

    1. Statement A is correct, and conclusions I and II are not correct explanations of A.
    2. Statement A is correct, and conclusions I and II are correct explanations of A.
    3. Statement A is correct, and conclusion I is the only correct explanation of A.
    4. Statement A correct, and conclusion II is the only correct explanation of A.
    Show answer

    Answer: (3) Statement A is correct, and conclusion I is the only correct explanation of A.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  17. Q18 · Thermodynamics & Heat Transfer · Thermodynamics

    Select the option that is true regarding the following two statements labelled Assertion (A) and Reason (R). Assertion (A): The performance of a simple Rankine cycle is not sensitive to the efficiency of the feed pump. Reason (R): The network ratio is practically unit for a Rankine cycle.

    1. Both A and R are individually true, but R is not the correct explanation of A.
    2. A is true, but R is not the correct explanation of A.
    3. A is false, but R is the correct explanation of A.
    4. Both A and R are individually true, and R is the correct explanation of A.
    Show answer

    Answer: (4) Both A and R are individually true, and R is the correct explanation of A.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  18. Q19 · Automobile Chassis & Transmission · Brakes

    Which of the following statements is INCORRECT about mechanical brakes?

    1. Brakes absorb energy and convert it to heat.
    2. The capacity of a brake depends largely on the surface area of frictional surfaces but independent of the actuation force applied.
    3. The durability of a brake or service life between maintenance depends heavily on the type of material used to line the shoe.
    4. Mechanical brakes all act by generating frictional forces as two surfaces rub against each other.
    Show answer

    Answer: (2) The capacity of a brake depends largely on the surface area of frictional surfaces but independent of the actuation force applied.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  19. Q20 · Automobile Chassis & Transmission · Brakes

    Which of the following is NOT the main part of your vehicle’s hydraulic brake system?

    1. Brake pad leaf spring
    2. Brake line
    3. Brake disc
    4. Leaf spring
    Show answer

    Answer: (4) Leaf spring

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  20. Q21 · Automobile Chassis & Transmission · Brakes

    Which of the following types of brakes is shown in the figure?

    Figure for question 21
    1. External expanding brake
    2. Internal expanding brake
    3. Centrifugal brake
    4. Hydraulic brake
    Show answer

    Answer: (2) Internal expanding brake

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  21. Q22 · Automobile Chassis & Transmission · Brakes

    What is the principle of hydraulic brake system?

    1. Zeroth law hydraulics
    2. Newton's law of friction
    3. Pascal's law pressure
    4. Fourier's law of conduction
    Show answer

    Answer: (3) Pascal's law pressure

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  22. Q23 · Automobile Chassis & Transmission · Brakes

    A braking system commonly used in heavy commercial vehicles and trucks that requires a heavy braking effort that can be applied by the driver’s leg alone is known as:

    1. Hydraulic brake system
    2. Internal expanding brake system
    3. Band brake system
    4. Air brake system
    Show answer

    Answer: (4) Air brake system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  23. Q24 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Match the following circuits of carburettor with their individual functions correctly.

    List IList II
    (A) Main circuit(i) Provides just enough fuel for fuel-efficient cruising
    (B) Idle circuit(ii) Provides just enough fuel to keep the engine idling
    (C) Power enrichment circuit(iii) Provides extra fuel when the car is going up a hill or towing a trailer
    (D) Choke(iv) Provides extra fuel when the engine is cold so that it will start
    1. (A)-(i), (B)-(ii), (C)-(iii) and (D)-(iv)
    2. (A)-(ii), (B)-(iii), (C)-(i) and (D)-(iv)
    3. (A)-(iv), (B)-(iii), (C)-(ii) and (D)-(i)
    4. (A)-(ii), (B)-(iii), (C)-(iv) and (D)-(i)
    Show answer

    Answer: (1) (A)-(i), (B)-(ii), (C)-(iii) and (D)-(iv)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  24. Q25 · Engineering Mechanics & Machine Design · Theory of Machines

    Match the following type gear trains with their functions.

    Gear typeFunctions
    (A) Simple gear train(i) The gear train in which axis of first gear and last gear is co-axial.
    (B) Compound gear train(ii) The gear train which consists of more than one gear on any shaft.
    (C) Epi-cyclic gear train(iii) The gear train in which the axis of one or more gear moves relative to the fixed axis of another gear.
    (D) Reverted gear train(iv) The gear train which consists of only one gear on each shaft.
    1. (A). - (i), (B). - (iii), (C).- (ii) and (D). - (iv)
    2. (A). - (iii), (B). - (ii), (C).- (iv) and (D). - (i)
    3. (A). - (iv), (B). - (ii), (C).- (iii) and (D). - (i)
    4. (A). - (iv), (B). - (i), (C).- (iii) and (D). - (ii)
    Show answer

    Answer: (3) (A). - (iv), (B). - (ii), (C).- (iii) and (D). - (i)

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  25. Q26 · Automobile Chassis & Transmission · Brakes

    In a master cylinder of a hydraulic brake system, the primary piston is the piston that is:

    1. near the front end of the car
    2. directly operated by the brake pedal
    3. hydraulically operated by the secondary piston
    4. operated by the return springs
    Show answer

    Answer: (2) directly operated by the brake pedal

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  26. Q28 · Automobile Chassis & Transmission · Clutch & Gearbox

    A single plate clutch has outer and inner diameters as 300 mm and 200 mm, respectively. The total force acting on the friction surface is 6000 N. If the coefficient of friction is 0.2, the power transmitted by the clutch at an angular speed of 300 rad/s is:

    1. 36 kW
    2. 90 kW
    3. 45 kW
    4. 30 kW
    Show answer

    Answer: (3) 45 kW

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  27. Q29 · Automobile Chassis & Transmission · Clutch & Gearbox

    Which of the following is NOT a type of clutch?

    1. Single plate type clutch
    2. Multiple plate clutch
    3. Centrifugal type clutch
    4. Governor type clutch
    Show answer

    Answer: (4) Governor type clutch

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  28. Q30 · Automobile Chassis & Transmission · Clutch & Gearbox

    Which of the following statements about the multi-plate clutch is INCORRECT?

    1. Multi-plate consists of a number of clutch plates.
    2. Multi-plate clutch has higher friction surface, which is a multiple of the number of clutch plates.
    3. The capacity of the multiple clutch to transmit torque however remains same as single plate clutch due to lower pressure between various friction plates.
    4. Wet multiple clutches are normally smaller in size, and the noise is also much less compared with dry clutches.
    Show answer

    Answer: (3) The capacity of the multiple clutch to transmit torque however remains same as single plate clutch due to lower pressure between various friction plates.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  29. Q31 · Materials, Manufacturing & Metrology · Metrology & Measurement

    A force transducer works on the __________.

    1. Hall effect principle
    2. Piezoelectric principle
    3. Laser principle
    4. Magneto Rheological principle
    Show answer

    Answer: (2) Piezoelectric principle

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  30. Q32 · Materials, Manufacturing & Metrology · Metrology & Measurement

    The tachogenerator is a device used to measure which of the following quantities?

    1. Force
    2. Torque
    3. Angular velocity
    4. Liquid level of the tank
    Show answer

    Answer: (3) Angular velocity

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  31. Q33 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following types of combustion chambers is NOT used in the spark ignition engine?

    1. T-head type chamber
    2. L-head chamber
    3. I-head type chamber
    4. Shallow depth chamber
    Show answer

    Answer: (4) Shallow depth chamber

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  32. Q34 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which combustion chamber is shown in the figure, and in which type of engine is it used?

    Figure for question 34
    1. Cylindrical chamber used in compression ignition engine
    2. Semi-spherical chamber used in spark ignition engine
    3. Toroidal chamber used in compression ignition engine
    4. Shallow depth combustion chamber used in spark ignition chamber
    Show answer

    Answer: (1) Cylindrical chamber used in compression ignition engine

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  33. Q35 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following types of combustion chambers is shown in the figure?

    Figure for question 35
    1. Swirl combustion chamber
    2. Shallow chamber
    3. F-head type chamber
    4. T-head type chamber
    Show answer

    Answer: (1) Swirl combustion chamber

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  34. Q36 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following operating variables is NOT affected due to ignition delay during compression ignition combustion?

    1. Injection pressure
    2. Compression temperature
    3. Air velocity in combustion chambers
    4. Suction air temperature
    Show answer

    Answer: (4) Suction air temperature

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  35. Q37 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The phenomenon of excessive turbulence increases combustion rapidly and leads to ________.

    1. high power generation
    2. low flame velocity
    3. detonation
    4. incomplete combustion
    Show answer

    Answer: (3) detonation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  36. Q38 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    The process of preparing a combustible fuel-air mixture outside the engine cylinder is known as:

    1. Knocking
    2. Vaporisation
    3. Carburation
    4. Compression
    Show answer

    Answer: (3) Carburation

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  37. Q39 · Automotive Electrical & Electronics · Lighting, Instruments & Wiring

    What is the maximum voltage range used in electrical circuits for two-wheeler vehicles?

    1. 24 V
    2. 12 V
    3. 6 V
    4. 4 V
    Show answer

    Answer: (2) 12 V

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  38. Q40 · Automotive Electrical & Electronics · Lighting, Instruments & Wiring

    What is voltage and power rating of rear, turn left signal lamp used in four-wheeler vehicles?

    1. 24 V and 12 watt
    2. 12 V and 5 watt
    3. 20 V and 10 watt
    4. 12 V and 10 watt
    Show answer

    Answer: (4) 12 V and 10 watt

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  39. Q41 · Automotive Electrical & Electronics · Starting & Ignition

    Which of the following is NOT a part of the capacitor discharge ignition unit?

    1. Charging coil
    2. Potentiometer
    3. Hall sensor
    4. Flywheel
    Show answer

    Answer: (2) Potentiometer

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  40. Q42 · Automotive Electrical & Electronics · Starting & Ignition

    An electrical device which is a combination of a distributor and generator built as one unit, making it different from the conventional distributor that creates spark energy without external voltage is known as:

    1. Voltage Regulator
    2. Alternator
    3. Capacitor Discharge Ignition
    4. Magneto
    Show answer

    Answer: (4) Magneto

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  41. Q43 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following is NOT a function of piston rings?

    1. Sealing the combustion chamber
    2. Controlling the thickness of the oil film on the cylinder wall
    3. Carrying the heat away from the cylinder into the piston
    4. Providing hydrodynamic lubrication
    Show answer

    Answer: (3) Carrying the heat away from the cylinder into the piston

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  42. Q44 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following types of piston rings located in the ring groove is closest to the crankcase?

    1. Oil ring
    2. Compression ring
    3. Wiper ring
    4. Heat transfer ring
    Show answer

    Answer: (1) Oil ring

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  43. Q45 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The piston is not parallel sided but tapered, usually with a barrel form as shown in the figure. The correct position for piston ______ measurement (point x) should be verified with the product supplier, as the exact point will vary by application.

    Figure for question 45
    1. bottom dead centre
    2. skirt diameter
    3. top dead centre
    4. Gudgeon pin thickness
    Show answer

    Answer: (2) skirt diameter

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  44. Q46 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    Which of the following manufacturing methods will produce the strongest piston using aluminium alloys?

    1. Marching processes
    2. Casting method
    3. Forging method
    4. Welding method
    Show answer

    Answer: (3) Forging method

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  45. Q47 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following parts of an engine is shown in the figure?

    Figure for question 47
    1. Piston cylinder
    2. Cylinder head
    3. Cylinder block
    4. Crankcase
    Show answer

    Answer: (3) Cylinder block

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  46. Q48 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following types of pistons is shown in the figure?

    Figure for question 48
    1. Domed piston
    2. Flat top piston
    3. Dished piston
    4. Relief valve piston
    Show answer

    Answer: (3) Dished piston

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  47. Q49 · Engineering Mechanics & Machine Design · Theory of Machines

    The maximum magnitude of the unbalanced force perpendicular to the line of stroke of an engine to cause the variation in pressure between the wheel and the rail such that the vehicle vibrates vigorously is known as:

    1. Swaying Couple
    2. Hammer Blow
    3. Resonance
    4. Natural Vibration
    Show answer

    Answer: (2) Hammer Blow

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  48. Q50 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The firing order in an engine is important because a correct firing order can cause ________.

    1. low pollution
    2. minimum vibration
    3. good air cooling
    4. low fuel consumption
    Show answer

    Answer: (2) minimum vibration

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  49. Q51 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Which of the following statements about torque tube drive is INCORRECT?

    1. The propeller shaft is enclosed by a hollow torque tube.
    2. Two universal joints are used.
    3. Load-carrying capability is very low.
    4. There is no slip joint in torque tube drive.
    Show answer

    Answer: (2) Two universal joints are used.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  50. Q52 · Automobile Chassis & Transmission · Steering & Suspension

    Which of the following steering mechanisms is shown in the figure?

    Figure for question 52
    1. Rack and pinion steering linkage
    2. Relay type steering linkage
    3. Gearbox steering linage
    4. Sliding steering linkage
    Show answer

    Answer: (1) Rack and pinion steering linkage

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  51. Q53 · Automobile Chassis & Transmission · Steering & Suspension

    Which of the following equations represents the basic condition for the steering mechanism for perfect rolling of all wheels? Consider φ = angle of inside lock; θ = angle of outside lock; b and c are the distances between real and front wheels and distance between front wheels, respectively.

    1. cot φ + cotθ = c/b
    2. cot φ − cotθ = c/b
    3. tan φ + tanθ = c/b
    4. tan φ − cotθ = c/b
    Show answer

    Answer: (2) cot φ − cotθ = c/b

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  52. Q54 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    The part of a lubrication system in piston engine whereby the crankcase sump is used as an integral oil reservoir is known as:

    1. dry sump reservoir
    2. dual lubrication sump reservoir
    3. wet sump reservoir
    4. cylinder case sump reservoir
    Show answer

    Answer: (3) wet sump reservoir

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  53. Q55 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    In which of the following types of engines is petroil lubrication system employed?

    1. Four-stroke diesel engine
    2. Four-stroke petrol engine
    3. Steam engine
    4. Two-stroke engines
    Show answer

    Answer: (4) Two-stroke engines

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  54. Q56 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which of the following types of lubrication systems is shown in the figure?

    Figure for question 56
    1. Petroil lubrication system
    2. Pressure lubrication system
    3. Pump lubrication system
    4. Dry lubrication system
    Show answer

    Answer: (2) Pressure lubrication system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  55. Q57 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    The metal fins on the internal combustion engine's cylinder head as shown in the figure are used for which of the following purposes?

    Figure for question 57
    1. To heat the air during suction stroke
    2. To dissipate the exhaust gases during exhaust stroke
    3. To increase heat dissipation rate of the cylinder head by air cooling
    4. To increase the heat dissipation rate of the cylinder head by water cooling
    Show answer

    Answer: (3) To increase heat dissipation rate of the cylinder head by air cooling

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  56. Q58 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    Which of the following types of internal combustion cooling system is shown in the figure?

    Figure for question 58
    1. Air syphon cooling system
    2. Gravitational water cooling system
    3. Buoyant syphon water cooling system
    4. Thermo-syphon water cooling system
    Show answer

    Answer: (4) Thermo-syphon water cooling system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  57. Q59 · Automobile Chassis & Transmission · Clutch & Gearbox

    A type of manual transmission system in which transmission changes occur between gears rotating at the same speed is known as:

    1. Differential transmission system
    2. Automatic transmission system
    3. Synchromesh transmission system
    4. Reverted gear transmission system
    Show answer

    Answer: (3) Synchromesh transmission system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  58. Q60 · Automobile Chassis & Transmission · Clutch & Gearbox

    Which of the following is the primary objective of an automatic transmission system?

    1. Allow the engine to operate in its narrow range of speeds while providing a wide range of output speeds.
    2. Allow the engine to operate at constant speeds while providing a wide range of output speeds.
    3. Allow the engine to operate in its wide range of speeds while providing a narrow range of output speeds.
    4. Allow the engine to operate in its wide range of speeds while providing a constant output speed.
    Show answer

    Answer: (1) Allow the engine to operate in its narrow range of speeds while providing a wide range of output speeds.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  59. Q61 · Automobile Chassis & Transmission · Clutch & Gearbox

    Which of the following statements is correct for the constant mesh gear box?

    1. It has the simplest design of gear box.
    2. It consists of helical gear.
    3. The size of the gearbox is large.
    4. It has more chance to damage the gear teeth during meshing.
    Show answer

    Answer: (2) It consists of helical gear.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  60. Q62 · Thermodynamics & Heat Transfer · Refrigeration & Air Conditioning

    Identify the odd one in terms of components of a car air conditioner.

    1. Compressor
    2. Condenser
    3. Evaporator
    4. Rectifier
    Show answer

    Answer: (4) Rectifier

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  61. Q63 · Thermodynamics & Heat Transfer · Refrigeration & Air Conditioning

    Match the columns.

    RefrigerationApplications
    (i) Domestic refrigeration(a) Holding and displaying frozen and fresh food in retail outlets
    (ii) Commercial refrigeration(b) Appliances used for keeping food in dwelling units
    (iii) Industrial refrigeration(c)Large equipment, typically 25 Kw to 30 MW
    (iv) Transport refrigeration(d) Used during transportation by road, rail, air and sea
    1. (i)-b, (ii)-c, (iii)-a, (iv)-d
    2. (i)-c, (ii)-b, (iii)-a, (iv)-d
    3. (i)-d, (ii)-b, (iii)-a, (iv)-c
    4. (i)-b, (ii)-a, (iii)-c, (iv)-d
    Show answer

    Answer: (4) (i)-b, (ii)-a, (iii)-c, (iv)-d

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  62. Q64 · Thermodynamics & Heat Transfer · Thermodynamics

    Which gas CANNOTbe used in a sterling engine?

    1. Air
    2. Hydrogen
    3. Helium
    4. Neon
    Show answer

    Answer: (4) Neon

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  63. Q65 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following options about the given assertion and reason is correct? Assertion (A): The air standard efficiency of the diesel cycle decreases as the load is increased. Reason (R): With increase of load, cut-off ratio increases.

    1. Both A and R are individually true and R is the correct explanation of A.
    2. Both A and R are individually true but R is not the correct explanation of A.
    3. A is true but R is false.
    4. A is false but R is true.
    Show answer

    Answer: (1) Both A and R are individually true and R is the correct explanation of A.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  64. Q66 · Automobile Chassis & Transmission · Steering & Suspension

    The main purpose of a wheel alignment is to:

    1. control vehicle direction
    2. stop the vehicle
    3. reduce tyre wear
    4. support vehicle weight
    Show answer

    Answer: (1) control vehicle direction / (3) reduce tyre wear

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  65. Q67 · Automobile Chassis & Transmission · Steering & Suspension

    Which of the following angles consists of the camber angle and steering axis angle?

    1. Toe-out
    2. Point of intersection
    3. Included angle
    4. Caster angle
    Show answer

    Answer: (3) Included angle

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  66. Q68 · Automobile Chassis & Transmission · Steering & Suspension

    Which of the following is a sign of bad wheel alignment?

    1. Good cornering effect
    2. Neutral steer
    3. The steering wheel returns to the centre
    4. The vehicle pulls to one side
    Show answer

    Answer: (4) The vehicle pulls to one side

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  67. Q69 · Automobile Chassis & Transmission · Steering & Suspension

    Match the columns.

    Wheel Alignment termsFunctions
    (i) Castor(a) Measures whether the front of a pair of wheels turns in or out, viewed from the front
    (ii) Camber(b) Measures the vertical tilt of the wheel
    (iii) Toe(c) Compares the steering axis to the vertical axis, when the car is viewed from the side
    (iv) Thrust(d) The imaginary line drawn perpendicular to the rear axles centre line
    1. (i) - c, (ii) - b, (iii) - a, (iv) - d
    2. (i) - d, (ii) - a, (iii) - b, (iv) - c
    3. (i) - b, (ii) - c, (iii) - d, (iv) - a
    4. (i) - c, (ii) - d, (iii) - b, (iv) - a
    Show answer

    Answer: (1) (i) - c, (ii) - b, (iii) - a, (iv) - d

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  68. Q70 · Thermodynamics & Heat Transfer · Thermodynamics

    During the throttling process ________ does not change.

    1. pressure
    2. internal energy
    3. entropy
    4. enthalpy
    Show answer

    Answer: (4) enthalpy

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  69. Q71 · Automobile Chassis & Transmission · Brakes

    In a disc brake, which component provides the pad-to-disc adjustment?

    1. Bleed screw
    2. Piston
    3. Caliper
    4. Piston seal
    Show answer

    Answer: (4) Piston seal

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  70. Q72 · Automobile Chassis & Transmission · Brakes

    Which of the following parts will face maximum wear?

    1. Brake drum
    2. Friction lining
    3. Wheel cylinders
    4. Retracting lever
    Show answer

    Answer: (2) Friction lining

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  71. Q73 · Automobile Chassis & Transmission · Brakes

    Read the given statement and conclusions carefully. Which of the given conclusions logically follow(s) from the statement? Statement: An air brake or, more formally, a compressed-air-brake system, is a type of friction brake for vehicles in which compressed air pressing on a piston is used to apply the pressure to the brake pad to stop the vehicle. Air brakes are used in large heavy vehicles. Conclusions: I) Air brakes are used in cars. II) Air brakes are used in trucks, buses, trailers and semi-trailers.

    1. Only Conclusion I follows
    2. Only Conclusion II follows
    3. Both conclusions follow
    4. Statement is true, both conclusions are false
    Show answer

    Answer: (2) Only Conclusion II follows

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  72. Q74 · Automobile Chassis & Transmission · Brakes

    What is the pressure on air brakes?

    1. 100 to 120 psi
    2. 80 to 90psi
    3. 150 to 200 psi
    4. 32 to 40 psi
    Show answer

    Answer: (1) 100 to 120 psi

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  73. Q75 · Automobile Chassis & Transmission · Brakes

    Match the columns.

    Braking TermsDefinition
    (i) Bleeding(a) Vacuum device that multiplies pedal effort
    (ii) Bluing(b) Discolouring of cast iron rotors due to heat
    (iii) Brake booster(c) Hydraulic pressure within the brake line
    (iv) Brake line pressure(d) Process of removing overheated fluid and air
    1. (i)-b, (ii)-d, (iii)-c, (iv)-a
    2. (i)-c, (ii)-a, (iii)-b, (iv)-d
    3. (i)-d, (ii)-c, (iii)-b, (iv)-a
    4. (i)-d, (ii)-b, (iii)-a, (iv)-c
    Show answer

    Answer: (4) (i)-d, (ii)-b, (iii)-a, (iv)-c

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  74. Q76 · Automobile Chassis & Transmission · Brakes

    Which of the following options about the given assertion and reason is correct? Assertion (A): Eddy current brakes use the drag force created by eddy currents as a brake to slow or stop moving objects. Reason (R): Mechanical energy is converted into resistive heat energy by the principle of energy conservation.

    1. Both A and R are correct and R is the correct explanation for A.
    2. Both A and R are correct but R is not the correct explanation for A.
    3. A is correct but R is incorrect.
    4. Both A and R are incorrect.
    Show answer

    Answer: (1) Both A and R are correct and R is the correct explanation for A.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  75. Q77 · Automobile Chassis & Transmission · Clutch & Gearbox

    Which of the following is NOT a friction clutch?

    1. Torque converter
    2. Centrifugal clutch
    3. Cone clutch
    4. Disc clutch
    Show answer

    Answer: (1) Torque converter

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  76. Q78 · Automobile Chassis & Transmission · Clutch & Gearbox

    What is the best word to describethe assembled parts of a clutch?

    1. Welded
    2. Bolted
    3. Riveted
    4. Solder
    Show answer

    Answer: (3) Riveted

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  77. Q79 · Automobile Chassis & Transmission · Clutch & Gearbox

    A clutch that consists of thin plates immersed in a bath of oil and has grooved surfaces for permitting the oil to flow through these plates is called:

    1. Multiple dry clutch
    2. Multiple wet clutch
    3. Semi-centrifugal clutch
    4. Centrifugal clutch
    Show answer

    Answer: (2) Multiple wet clutch

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  78. Q80 · Automobile Chassis & Transmission · Clutch & Gearbox

    _______ is a type of clutch used in motorcycles.

    1. Single plate
    2. Multi-plate
    3. Diaphragm
    4. Centrifugal
    Show answer

    Answer: (2) Multi-plate

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  79. Q81 · Automobile Chassis & Transmission · Clutch & Gearbox

    A pilot bearing that is worn or lacks lubricant will produce noise in the clutch when which condition exists?

    1. Transmission is in gear
    2. Clutch is disengaged
    3. Vehicle is standing still
    4. Clutch is engaged
    Show answer

    Answer: (2) Clutch is disengaged

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  80. Q82 · Automobile Chassis & Transmission · Clutch & Gearbox

    Match the columns.

    Parts NameFunctions
    (i)Torque converter(a) Produces pressure
    (ii) Input shaft(b) Actuate the bands and clutches
    (iii) Oil pump(c) Produces pressure fluid coupling that connects and disconnects the engine and transmission
    (iv) Piston and servos(d) Transfers power from torque converter to internal drive member
    1. (i)-c, (ii)-d, (iii)-a, (iv)-b
    2. (i)-d, (ii)-c, (iii)-b, (iv)-a
    3. (i)-b, (ii)-c, (iii)-d, (iv)-a
    4. (i)-b, (ii)-a, (iii)-c, (iv)-d
    Show answer

    Answer: (1) (i)-c, (ii)-d, (iii)-a, (iv)-b

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  81. Q83 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which ofthe givenstatements are correct? 1. In the SI engines, detonation occurs near the end of combustion; whereas in CI engines, knocking occurs near the beginning of combustion. 2. In SI engines, no problems are encountered on account of pre-ignition. 3. Low inlet pressure and temperature reduce knocking tendency in SI engines but increase the knocking tendency in CI engines.

    1. 1, 2 and 3
    2. Only 1 and 2
    3. Only 2 and 3
    4. Only 1 and 3
    Show answer

    Answer: (4) Only 1 and 3

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  82. Q84 · Automotive Electrical & Electronics · Batteries & Charging

    Which component is used to charge the battery driven by the engine?

    1. Condenser
    2. Rectifier
    3. Alternator
    4. Relay
    Show answer

    Answer: (3) Alternator

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  83. Q85 · Automotive Electrical & Electronics · Starting & Ignition

    The output of an ignition coil is connected to which of the following parts?

    1. Battery
    2. Ammeter
    3. Distributor cap
    4. Spark plug
    Show answer

    Answer: (3) Distributor cap

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  84. Q86 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    What is the temperature of the intake valve?

    1. 200°C to 300°C
    2. 300°C to 400°C
    3. 400°C to 500°C
    4. 500°C to 600°C
    Show answer

    Answer: (1) 200°C to 300°C

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  85. Q87 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    During a power stroke, the downward moment of the piston isdone due to which pressure or force?

    1. Fuel pressure
    2. Gas pressure
    3. Solid pressure
    4. Liquid pressure
    Show answer

    Answer: (2) Gas pressure

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  86. Q88 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Match the columns.

    IC Engine TerminologyFunction
    (i) Bore(a) Distance between TDC and BDC
    (ii) Stroke(b) Combined volume of all engines
    (iii) Engine displacement(c) SI engine
    (iv) Spark plug(d) Internal diameter of cylinder
    1. (i)-c, (ii)-d, (iii)-a, (iv)-b
    2. (i)-d, (ii)-a, (iii)-b, (iv)-c
    3. (i)-a, (ii)-b, (iii)-c, (iv)-d
    4. (i)-c, (ii)-a, (iii)-d, (iv)-b
    Show answer

    Answer: (2) (i)-d, (ii)-a, (iii)-b, (iv)-c

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  87. Q89 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Read the given statement and conclusions carefully. Which of the given conclusions logically follow(s) from the statement? Statement: A piston is a component of reciprocating engines, reciprocating pumps, gas compressors, hydraulic cylinders and pneumatic cylinders, among other similar mechanisms. Conclusions: I) It is the moving component that is contained by a cylinder and is made gas-tight by piston rings. II) Its purpose is to transfer force from expanding gas in the cylinder to the crankshaft via a piston rod.

    1. Only Conclusion I follows
    2. Only Conclusion II follows
    3. Both conclusions follow
    4. The statement is true but the conclusions are false
    Show answer

    Answer: (3) Both conclusions follow

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  88. Q90 · Engineering Mechanics & Machine Design · Theory of Machines

    In balancing of single cylinder engine, the rotating unbalance is:

    1. Completely made zero and so also the reciprocating unbalance
    2. Completely made zero and the reciprocating unbalance is partially reduced
    3. Partially reduced and the reciprocating unbalance is completely made zero
    4. Partially reduced and so also the reciprocating unbalance
    Show answer

    Answer: (2) Completely made zero and the reciprocating unbalance is partially reduced

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  89. Q91 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    The air cooling system helps to dissipate the heat from which of the following parts?

    1. Engine piston
    2. Engine crank shaft
    3. Exhaust pipe
    4. Cylinder and head fins
    Show answer

    Answer: (4) Cylinder and head fins

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  90. Q92 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What is the main purpose of a lubricant?

    1. To minimise the friction
    2. To increase the friction
    3. To increase the weariness
    4. To increase the noise
    Show answer

    Answer: (1) To minimise the friction

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  91. Q93 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Identify the INCORRECT statement related to the properties of a lubricant.

    1. It should have low viscosity.
    2. It should remain stable under changing temperatures.
    3. It should keep lubricated pans clean.
    4. It should not corrode metallic surfaces.
    Show answer

    Answer: (1) It should have low viscosity.

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  92. Q94 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Identify the multi-grade oil.

    1. SAE 10W 30
    2. SAE 25W
    3. SAE 10
    4. SAE 20W
    Show answer

    Answer: (1) SAE 10W 30

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  93. Q95 · IC Engines, Fuels & Emissions · Cooling & Lubrication

    The pressure feed lubrication system does NOT lubricate which of the following parts?

    1. Timing gears
    2. Valve rods and push rods
    3. Rocker arms
    4. Main bearings of crankshaft
    Show answer

    Answer: (2) Valve rods and push rods

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  94. Q96 · Automotive Electrical & Electronics · Lighting, Instruments & Wiring

    The temperature gauge, which is most often located on your dashboard, indicates the temperature of:

    1. lubricating oil
    2. engine cylinder
    3. jacket cooling water
    4. engine piston
    Show answer

    Answer: (3) jacket cooling water

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  95. Q97 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    ______ is typically sucked into the cylinder during the suction stroke in the fuel supply system.

    1. Diesel
    2. Air
    3. Water
    4. Oil
    Show answer

    Answer: (2) Air

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  96. Q98 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In which stroke of the petrol engine, ‘exhaust gases’ is released to the atmosphere?

    1. Exhaust stroke
    2. Power stroke
    3. Compression stroke
    4. Intake stroke
    Show answer

    Answer: (1) Exhaust stroke

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  97. Q99 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    Which of the following components of the engine system cleans the air before it enters the cylinder of the engine?

    1. Crank
    2. Piston ring
    3. Filter
    4. Spark plug
    Show answer

    Answer: (3) Filter

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  98. Q100 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    ______ atomizes the fuel and mixes it with air in an I.C. engine.

    1. Camshaft
    2. Spark plug
    3. Piston
    4. Carburetor
    Show answer

    Answer: (4) Carburetor

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  99. Q101 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    What condition does the engine require while idling in a spark ignition (SI) engine?

    1. Maximum power output
    2. Heavy load demand
    3. Overheating
    4. No power demand
    Show answer

    Answer: (4) No power demand

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  100. Q102 · IC Engines, Fuels & Emissions · Fuel Supply & Combustion

    When all the air supplied is fully utilized, a spark ignition (SI) engine produce ______?

    1. minimum power
    2. maximum power
    3. no power
    4. average power
    Show answer

    Answer: (2) maximum power

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  101. Q103 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In which type of engine, petrol is used as fuel?

    1. Steam engine
    2. Spark ignition engine
    3. Diesel engine
    4. Turbine engine
    Show answer

    Answer: (2) Spark ignition engine

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  102. Q104 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which of the following statements is correct regarding the fuel properties in an automobile system? I. The volatile fuels are always preferred due to presence of constituents providing easiness in starting of engine in cold weather. II. The vaporization of fuel immediately after the engine starts is affected by the speed with which it is warmed up.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer: (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  103. Q105 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    To get petrol from crude oil, it is primarily ______ in a refinery.

    1. filtered
    2. compressed
    3. distilled
    4. oxidized
    Show answer

    Answer: (3) distilled

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  104. Q106 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What is the primary source of most of the petrol used in automobiles?

    1. Natural gas
    2. Coal
    3. Crude oil
    4. Biofuels
    Show answer

    Answer: (3) Crude oil

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  105. Q107 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    Which method improves the antiknock qualities of the straight run gasoline by changing their molecular structure?

    1. Reforming
    2. Alkylation
    3. Cracking
    4. Polymerization
    Show answer

    Answer: (1) Reforming

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  106. Q108 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What calorific value of fuel is necessary for efficient operation in an automobile?

    1. High calorific value
    2. Low calorific value
    3. Average calorific value
    4. Fuel power does not depend upon its calorific value
    Show answer

    Answer: (1) High calorific value

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  107. Q109 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What are the primary components of LPG used as fuel in an automobile?

    1. Methane and ethane
    2. Hydrogen and helium
    3. Butane and propane
    4. Oxygen and nitrogen
    Show answer

    Answer: (3) Butane and propane

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  108. Q110 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    ______ connects the transmission main or output shaft of the gear box to the differential of the rear axle.

    1. Propeller shaft
    2. Radiator
    3. Airbags
    4. Alternator
    Show answer

    Answer: (1) Propeller shaft

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  109. Q111 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    The ‘Drive shaft’ in a vehicle is also called ______.

    1. Propeller shaft
    2. Steering wheel
    3. Seat belt
    4. Axle beam
    Show answer

    Answer: (1) Propeller shaft

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  110. Q112 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    What is provided to accommodate changes in the length of the propeller shaft?

    1. Coupling
    2. Universal joint
    3. Slip joint
    4. Drive belt
    Show answer

    Answer: (3) Slip joint

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  111. Q113 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    What is added in an automobile to provide relative motion to both the rear wheels when the vehicle is turning?

    1. Radiator
    2. Differential
    3. Gear box
    4. Steering wheel
    Show answer

    Answer: (2) Differential

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  112. Q114 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    What is that principle which is similar to the principle of ‘differential’?

    1. Spring balance
    2. Thermometer
    3. Pressure cooker
    4. Weighing beam
    Show answer

    Answer: (4) Weighing beam

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  113. Q115 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    In addition of its primary function, the ‘rear axle’ also serves as what in a vehicle’s chassis?

    1. A hydraulic pump
    2. A fuel tank
    3. A cooling system
    4. A beam subjected to a bending load
    Show answer

    Answer: (4) A beam subjected to a bending load

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  114. Q116 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Which of the following statements is correct regarding the types of rear axle of an automobile? I. Dead axles do not rotate with the wheels but the wheels rotate on it. II. Live axles are those axles which are attached to the wheel so that both of them rotate together.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer: (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  115. Q117 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Which of the following types of vehicles typically has a dead rear axle?

    1. Sports cars
    2. Horse-drawn vehicles
    3. Motorcycles
    4. Electric scooters
    Show answer

    Answer: (2) Horse-drawn vehicles

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  116. Q118 · Automobile Chassis & Transmission · Clutch & Gearbox

    ______ allows a clutch to function in a vehicle’s transmission system?

    1. Magnetic force
    2. Friction
    3. Electrical current
    4. Hydraulic pressure
    Show answer

    Answer: (2) Friction

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  117. Q119 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which process is responsible for expelling the exhaust gases from the cylinder during the exhaust stroke of the engine?

    1. Knocking
    2. Combustion
    3. Scavenging
    4. Ignition
    Show answer

    Answer: (3) Scavenging

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  118. Q120 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Exhaust gases are pushed out of the cylinder by the motion of what component in an engine?

    1. Spark plug
    2. Carburettor
    3. Piston
    4. Crankshaft
    Show answer

    Answer: (3) Piston

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  119. Q121 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    Which of the following statements is correct regarding the exhaust stroke in Four-stroke Otto Cycle Engine? I. The suction valve remains closed and exhaust valve is open. II. As the piston moves from BDC to TDC, it pushes the gases out through exhaust valves.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer: (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  120. Q122 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In a four-stroke diesel engine cycle, when does the exhaust valve typically open?

    1. At the beginning of the compression stroke
    2. Just before the end of expansion
    3. During the intake stroke
    4. At the start of the power stroke
    Show answer

    Answer: (2) Just before the end of expansion

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  121. Q123 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    What is the most important gas produced during combustion in an automobile engine that increases the atmospheric temperature?

    1. O₂
    2. CO₂
    3. N₂
    4. SO₂
    Show answer

    Answer: (2) CO₂

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  122. Q124 · IC Engines, Fuels & Emissions · Fuels, Lubricants & Emissions

    In the automobile engine, which two gases in the exhaust vary opposite to each other?

    1. SO₂ and O₂
    2. O₂ and CO
    3. CO₂ and CO
    4. SO₂ and N₂
    Show answer

    Answer: (3) CO₂ and CO

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  123. Q125 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    The exhaust of spent gases from the cylinder of an automobile engine is done so that ______.

    1. the engine can run silently
    2. fuel efficiency is improved
    3. fresh charge may be sucked in
    4. the exhaust note becomes louder
    Show answer

    Answer: (3) fresh charge may be sucked in

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  124. Q126 · IC Engines, Fuels & Emissions · Engine Fundamentals & Cycles

    In a four stroke diesel cycle engine, during which piston movement does it push gases through the exhaust valves?

    1. From TDC towards BDC
    2. From BDC towards TDC
    3. From TDC to BDC and back to TDC
    4. No piston movement required
    Show answer

    Answer: (2) From BDC towards TDC

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  125. Q127 · Motor Vehicles Act, Transport & Maintenance · Vehicle Maintenance & Testing

    What equipment is called ‘a tray on wheels for mechanics to lie down on’?

    1. Wrench
    2. Creeper
    3. Sinter
    4. Hacksaw
    Show answer

    Answer: (2) Creeper

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  126. Q128 · Automobile Chassis & Transmission · Wheels & Tyres

    Where is the tyre-tube assembly mounted in a vehicle?

    1. Over the wheel rim
    2. On the rear axle
    3. On the gear box
    4. On the differential
    Show answer

    Answer: (1) Over the wheel rim

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  127. Q129 · Automobile Chassis & Transmission · Wheels & Tyres

    ______ is the final contact point between the road and the vehicle.

    1. Gear box
    2. Tyres
    3. Wheel hubs
    4. Differential
    Show answer

    Answer: (2) Tyres

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  128. Q130 · Automobile Chassis & Transmission · Wheels & Tyres

    In an automobile, what is the ‘tread’?

    1. The engine compartment
    2. The steering wheel
    3. Automobile’s dashboard
    4. The outer portion of the tyre that makes contact with the road surface
    Show answer

    Answer: (4) The outer portion of the tyre that makes contact with the road surface

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  129. Q131 · Automobile Chassis & Transmission · Wheels & Tyres

    What are the rings that fit on the rim of the wheel and connect the tyre to the rim called?

    1. Beads
    2. Hubs
    3. Valves
    4. Axles
    Show answer

    Answer: (1) Beads

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  130. Q132 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    In an automobile system, transmission system is also called ______.

    1. Differential
    2. Gear box
    3. Power train
    4. Wheel rim
    Show answer

    Answer: (3) Power train

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  131. Q133 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    What system transmits the power developed by the engine of the automobile to the driving wheels?

    1. Brake System
    2. Transmission System
    3. Steering System
    4. Ignition System
    Show answer

    Answer: (2) Transmission System

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  132. Q134 · Automobile Chassis & Transmission · Clutch & Gearbox

    ______ enables the driver to disconnect the drive from the road wheels instantaneously and to engage drive from the engine to the road wheels gradually.

    1. Gear box
    2. Spark plug
    3. Crown wheel
    4. Clutch
    Show answer

    Answer: (4) Clutch

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  133. Q135 · Automobile Chassis & Transmission · Clutch & Gearbox

    Which of the following component in an automobile provides the necessary leverage variation between the engine and road wheels?

    1. Differential
    2. Gear box
    3. Brakes
    4. Steering wheel
    Show answer

    Answer: (2) Gear box

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  134. Q136 · Automobile Chassis & Transmission · Clutch & Gearbox

    In an automobile, under what condition is the clutch typically disengaged?

    1. When accelerating
    2. When idling at a stoplight
    3. When shifting gears
    4. Clutch is never disengaged
    Show answer

    Answer: (3) When shifting gears

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  135. Q137 · Automobile Chassis & Transmission · Clutch & Gearbox

    How should the clutch be engaged to avoid a sudden jerk?

    1. Keep it disengaged at all times
    2. Should engage gradually
    3. Only engage it when coming to a complete stop
    4. Engage it quickly
    Show answer

    Answer: (2) Should engage gradually

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  136. Q138 · Automobile Chassis & Transmission · Steering & Suspension

    What to do if steering becomes hard due to low tyre inflation?

    1. Increase the engine’s RPM
    2. Replace the whole steering wheel
    3. Inflate the tyres to the specified pressure
    4. Ignore the problem, it will correct itself
    Show answer

    Answer: (3) Inflate the tyres to the specified pressure

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  137. Q139 · Automobile Chassis & Transmission · Steering & Suspension

    In an automobile, which system’s primary function is to achieve angular motion of the front wheels to negotiate a turn?

    1. Steering system
    2. Brake system
    3. Ignition system
    4. Transmission system
    Show answer

    Answer: (1) Steering system

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  138. Q140 · Engineering Mechanics & Machine Design · Machine Design

    In an automobile, what type of stress induced in the shafts due to the transmission of torque?

    1. Bending stress
    2. Shear stress
    3. Principle stress
    4. Torsional stress
    Show answer

    Answer: (2) Shear stress

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  139. Q141 · Engineering Mechanics & Machine Design · Machine Design

    In an automobile, what type of stress induced in the shafts due to the forces acting upon machine elements like gears, pulleys etc.?

    1. Bending stress
    2. Shear stress
    3. Principle stress
    4. Hoop stress
    Show answer

    Answer: (1) Bending stress

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  140. Q142 · Engineering Mechanics & Machine Design · Machine Design

    In an automobile, what is the typical cross-sectional shape of the shaft?

    1. Circular
    2. Rectangular
    3. Triangular
    4. Tubular
    Show answer

    Answer: (4) Tubular

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  141. Q143 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    What is the primary function of a Universal Joint in the shaft of an automobile?

    1. To steer the vehicle
    2. To connect the engine to the wheels
    3. To provide power to the lights
    4. For up and down movements of the rear axle when the vehicle is running
    Show answer

    Answer: (4) For up and down movements of the rear axle when the vehicle is running

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  142. Q144 · Engineering Mechanics & Machine Design · Theory of Machines

    How can the critical whirling speed of a shaft be increased?

    1. Reducing its length
    2. Reducing its diameter
    3. Increasing its diameter
    4. Increasing its weight
    Show answer

    Answer: (3) Increasing its diameter

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  143. Q145 · Automobile Chassis & Transmission · Drive Line, Axles & Differential

    Which of the following statements is correct regarding the ‘half shafts’ of an automobile? I. It is called half shafts because it normally transmits half of the available power from the differential to the wheel to which it is connected. II. Each half shaft uses a constant velocity joint at both the inboard (differential) and outboard (wheel) end.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer: (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  144. Q146 · Automobile Chassis & Transmission · Chassis & Body

    ______ is commonly used for making the windscreen of a vehicle.

    1. Laminated safety glass
    2. Aluminium
    3. Wrought iron
    4. Plastic
    Show answer

    Answer: (1) Laminated safety glass

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  145. Q147 · Automobile Chassis & Transmission · Wheels & Tyres

    What function does ‘Sulphur’ perform in relation to tyre material in the production of rubber?

    1. Speed enhancer
    2. Vulcanizing agent
    3. Helps in better gripping on the road
    4. Helps in better turning on the road
    Show answer

    Answer: (2) Vulcanizing agent

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  146. Q148 · Automobile Chassis & Transmission · Chassis & Body

    Which of the following statements is correct regarding the materials used in body work of an automobile? I. Steel is still used in majority of the cases being the cheapest along with the case with which it can be stamped out to form various shapes. II. Thermoplastics are quite often used for components like boot coves, grills etc.

    1. Only I
    2. Only II
    3. Both I and II
    4. Neither I nor II
    Show answer

    Answer: (3) Both I and II

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  147. Q149 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    ______ is commonly used to tighten or loosen screws in a machine element of an automobile.

    1. Screw driver
    2. Pliers
    3. Reamer
    4. Sinter
    Show answer

    Answer: (1) Screw driver

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.

  148. Q150 · Materials, Manufacturing & Metrology · Manufacturing & Workshop

    What tool is used for cutting metal with a hammer in an automobile maintenance workshop?

    1. Pliers
    2. Chisels
    3. Hacksaw
    4. Solder
    Show answer

    Answer: (2) Chisels

    Explanation: open it in the practice app. It needs the ₹149 All-in-One Pass: one payment for every exam on the site.